Atmel SAM D20 MCU Family Features ARM Cortex M0+ Core

Atmel has just announced its SAM D20 family of embedded Flash micro-controllers based on ARM Cortex-M0+ processor core, designed for low power applications such as home automation, consumer, smart metering and industrial applications.

Atmel SAMD20 Xplained PRO Evaluation Kit
Atmel SAM D20 Xplained Pro Evaluation Kit

The key features of Atmel SAM D20 MCUs are as follows:

  • Cortex M0+ @ 48MHz, 2.14 Coremark/MHz
  • Single-cycle IO access, supporting a pin toggling frequency up to 24 MHz
  • Eight-channel event system
  • Peripherals:
    • Four to six serial communication modules (SERCOM) configurable as UART/USART, SPI or I2C
    • Up to eight 16-bit Timer/Counters
    • Peripheral touch controller (PTC) that supports up to 256 channels and supports buttons, sliders, wheels, and proximity
    • Real Time Clock (RTC) and calendar with leap year correction
    • 12-bit 350ksps ADC and 10-bit DAC
  • Power Consumption:
    • <150µA/MHz
    • <2µA RAM retention and RTC
    • Options between internal and external oscillators and on-the-fly clock switching

The family supports features 14 new devices available in 32-, 48- and 64-pin package options with 16 to 256KB of Flash memory, and 2 to 32KB RAM.

Atmel_SAM_D20_Block_Diagram
Atmel SAMD20 Block Diagram

SAM D20 series is supported by the same Atmel Studio and Atmel Software Framework used for Atmel AVR MCUs. The company also providesSAM D20 Xplained Pro evaluation kit (Pictured at the top of this post) with the following specifications:

  • SAMD20J18 microcontroller (64-pin package, 32KB SRAM, 256KB flash)
  • One mechanical reset button
  • One mechanical user pushbutton (wake-up, bootloader entry or general purpose)
  • One yellow user LED
  • 32.768kHz crystal
  • 3 Xplained Pro extension headers
  • Program/debug interface for external targets
  • Embedded Debugger
    • Auto-ID for board identification in Atmel Studio 6.1
    • One yellow status LED
    • One green board power LED
    • Symbolic debug of complex data types including scope information
    • Programming and debugging
    • Data Gateway Interface: SPI, I²C, 4 GPIOs
    • Virtual COM port (CDC)
  • USB powered
  • Supported with application examples in Atmel Software Framework

The Xplained PRO kit also comes pre-loaded with software that can be re-programmed, debugged and prototyped without any additional tools.

Samples of 128KB 32-pin, and 256KB 48-and 64 pin products are available in QFN and QFP packages now with pricing starting at $1.02 USD for 1K units of the 16KB, 32-pin QFN package. SAM D20 Xplained Pro kit can be purchased for $39 from Atmel Store.

Further information is available on Atmel SAM D20 microsite, and you may want to read “An intelligent remote control with Atmel’s SAM D20 under the hood” blog post to see a practical application using SAM D20 MCU.

Share this:

Support CNX Software! Donate via cryptocurrencies, become a Patron on Patreon, or purchase goods on Amazon or Aliexpress

ROCK Pi 4C Plus
Subscribe
Notify of
guest
The comment form collects your name, email and content to allow us keep track of the comments placed on the website. Please read and accept our website Terms and Privacy Policy to post a comment.
2 Comments
oldest
newest
renw0rp
renw0rp
10 years ago

One question – why Atmel dev boards are kind of expensive? STMicroelectronics has their Discovery kits priced much more aggressively. For example: Cortex-M3+ accelerometer+gyro/compass for ~$17 or Cortex-M4 (they don’t call them M4F coz all of their M4s have FPU) with DAC, digital microphone and accelerometer for ~$15 Also STM states their Cortex-M3 from “ultra low power” line is quite efficient, getting the job done much faster then M0 (there is big difference in the architecture: M0 is von Neuman, other Cortex-es are Harvard) and then it can switch to one of lower power modes; also some job, like putting… Read more »

Khadas VIM4 SBC