$14 Orange Pi R1 Allwinner H2+ Board Comes with Two Ethernet Ports, 256 MB RAM

Shenzhen Xunlong has introduced the new Orange Pi R1 board with Allwinner H2+ quad core Cortex A7 processor that’s a bit different from their other models, as it includes two 10/100M Ethernet port, and should be suitable for intelligent controllers, or simple IoT gateways.

Click to Enlarge

Orange Pi R1 board specifications:

  • SoC – Allwinner H2(+) quad core Cortex A7 processor @ 1.2 GHz with Mali-400MP2 GPU
  • System Memory – 256 DDR RAM
  • Storage – micro SD card slot, 16 MB SPI flash
  • Connectivity – 2x 10/100M Ethernet (including on via RTL8152B USB to Ethernet) + 802.11 b/g/n WiFi (Realtek RTL8189ETV) with u.FL antenna connector and external antenna
  • USB – 1x micro USB OTG port
  • Expansion headers
    • Unpopulated 26-pin “Raspberry Pi B+” header
    • 13-pin header with headphone, 2x USB 2.0, TV out, microphone and IR receiver signals
  • Debugging – 3-pin header for serial console
  • Power Supply – 5V via micro USB port
  • Dimensions – 60 x 45 mm

Since it’s based on the same Allwinner H2+ processor as on Orange Pi Zero board, the extra Ethernet port is implemented via USB, and the I/O headers looks to be the same, it should be possible to run Armbian images on the board without that many modifications. The board may not be the best solution for small router, as there are already many cheap OpenWrt compatible routers that should do the job just as well, but thanks to the expansion header, it may make a useful intelligent controller or ModBus gateway to manage relays, sensors, robots, etc…

Potential Use Case for Orange Pi R1 Boards – Source: MGate MB3170 Product Page

If you have the kind of cascaded setup above, the 16MB SPI flash could save you the use of micro SD card, with network boot either from the control PC (if it is always on), or one of the Orange Pi R1 fitted with a micro SD card.

Orange Pi R1 board is sold for $13.90 plus shipping ($17.29 in total here) on Aliexpress.

Thanks to Anton for the tip

Share this:

Support CNX Software! Donate via cryptocurrencies, become a Patron on Patreon, or purchase goods on Amazon or Aliexpress

ROCK Pi 4C Plus
Subscribe
Notify of
guest
The comment form collects your name, email and content to allow us keep track of the comments placed on the website. Please read and accept our website Terms and Privacy Policy to post a comment.
16 Comments
oldest
newest
LBO
LBO
6 years ago

Why always using so low RAM?! :/

proggerbg
proggerbg
6 years ago

LBO :
Why always using so low RAM?! :/

256 MB is plenty

Rogan
Rogan
6 years ago

In my opinion, they would have done better to have started with the Orange Pi Zero Plus, and replaced the RTL8211E with a RTL8363SB, and simply attached two GbE ports to that. As a switch, it should be functional even if the OS crashes (apart from needing initial setup, perhaps?), but reduces the packet forwarding load on the CPU, especially for the unit closest to the start of the daisy chain!

And the OS could reconfigure that as desired for VLAN’s, etc, if controlled forwarding is actually desired.

TLS
TLS
6 years ago

How did they manage to confuse the Wi-Fi module with the Ethernet chip? That’s a real rookie mistake…

tkaiser
tkaiser
6 years ago

@TLS Yes, annoying. But based on past experiences we should be able to trust in the information provided by the picture. That’s 16 MB SPI NOR flash (making it possible to run something like *Wrt/LEDE on it without additional storage) and RTL8152B. I picked up a NanoPi NEO yesterday, booted with Armbian’s legacy kernel (3.4.113), attached an RTL8152 dongle to it and now run an infite iperf3 test against another machine to get an idea about stability with the old kernel. With mainline kernel RTL8152B/8153 should have no issues and both should be even supported by mainline u-boot. On a… Read more »

Megous
Megous
6 years ago

@tkaiser
USB OTG is already activated and works well with the 4.13 mainline kernel. For networking it’s best to use the 4.13 mainline kernel as it contains better ethernet driver than my older kernel branches, which had problems with crashing under heavy load (on gigabit ethernet boards), when the kernel was not able to allocate packet buffers. (it would panic instead of dropping the packet)

TC
TC
6 years ago

16MB SPI… Time for a board bring-up in LEDE forums, right?

theguyuk
theguyuk
6 years ago

@proggerbg
If you can trust Aliexpress order numbers the Orange Pi Zero H2+ 512 out sells the 256 by nearly 3 times the amount of 256 sales.

theguyuk
theguyuk
6 years ago
Mario
Mario
6 years ago

Hi! I have just ordered a OPi R1. I have been googling a lot to figure out how to connect a monitor to the device (preferably via HDMI), but without success. I saw some references to an expansion board, but when I googled for that I only found expansion boards for OPi Zero. Would anyone in this forum be able to help me? Thanks in advance. Regards, Mario

capcoding
capcoding
4 years ago

except Nano Pi R1 is way more expensive $29 without SD card or any flash, adding a $8 SD card and shipping you’re looking at $29+$8+$8=$45, that’s enough to buy some decent openwrt routers already.

Not Sure
Not Sure
4 years ago

For OpenWrt like “firmware” 256M sure is enough (if the WiFi would be capable enough, which often is not the case of the onboard WiFi of some ARMboards…) but with a bit more it would make a nice FreedomBox.
I’d like to find small systems I can throw at my neighbours to get them meshed… but 802.11s (mesh point) is one of the 1st features these onboard WiFi chips are lacking…

Khadas VIM4 SBC