Makerfabs MaTouch ESP32-P4 TFTTouch 10.1 MIPI with 4G LTE is an ESP32-P4 + ESP32-C6-based display development platform for HMI edge AI, and connected embedded applications. The development board features a 10.1-inch IPS LCD, very similar to those of Seeed Studio’s reTerminal D1001, Waveshare ESP32-P4-WIFI6-Touch-LCD, and CrowPanel Advanced 7-inch displays.
However, what makes it unique compared to other devices is that it also features a SIM7670G 4G LTE modem with a SIM card slot, an RJ45 Ethernet jack, and a 2MP camera. The HMI display also comes with microphone and speaker connectors, a microSD card slot, various USB interfaces, lithium battery support, and two 2.54 mm pitch GPIO expansion headers exposing UART, I2C, SPI, and other peripheral interfaces. All these features make it suitable for HMI, edge AI, and connected embedded applications.
Makerfabs MaTouch ESP32-P4 10.1-inch 4G LTE specifications:
- SoC – Espressif Systems ESP32-P4NRW32
- CPU
- Dual-core 32-bit RISC-V HP (High-performance) CPU @ up to 400 MHz with AI instructions extension and single-precision FPU
- Single-RISC-V LP (Low-power) MCU core @ up to 40 MHz
- Memory
- 768 KB HP L2MEM (for dual-core CPU), 32 KB LP SRAM, 8 KB TCM (for LP MCU core)
- 32MB PSRAM
- Storage – 128 KB HP ROM, 16 KB LP ROM
- GPU – 2D Pixel Processing Accelerator (PPA)
- VPU – H.264 and JPEG codecs support
- CPU
- Storage
- 16MB QSPI NOR Flash
- MicroSD card slot
- Display
- 10.1-inch IPS LCD, 1280×800 resolution
- MIPI DSI interface (JD9365 LCD driver)
- 10-point capacitive touchscreen (GSL3680 touch driver)
- Camera – 2MP MIPI camera (SC2336) supporting up to 1920×1080 resolution
- Audio – Onboard microphone, speaker output header via ES8311 audio codec and NS4150 audio amplifier
- Networking
- Wireless – ESP32-C6
- 2.4 GHz WiFi 6
- Bluetooth 5.x LE
- 802.15.4 radio for Zigbee, Thread, and Matter
- Wired Networking – 10/100Mbps Ethernet via IP101GRI PHY
- Cellular
- SIMCom SIM7670G 4G LTE Cat 1 module with Nano SIM card slot
- 4G LTE antenna
- Wireless – ESP32-C6
- USB – 6x USB Type-C ports
- USB-TTL (CH340K via USB to UART chipset)
- USB-NATIVE
- USB-CDC/JTAG
- USB-OTG
- USB-DEVICE
- USB-LTE (dedicated to the SIM7670G cellular module)
- Expansion – 2x 40-pin headers exposing 26x GPIOs, 3.3V, 5V, and GND
- Misc
- Power ON/OFF switch
- Reset and Boot buttons
- Power LED, Status RGB LED
- PCF8563T RTC with CR1220 battery support for timed interrupt wake-up
- Power Supply
- 5.0V (4.0V~5.25V) via USB Type-C port
- 2,500 mAh battery (2-pin lithium battery connector with TP4056 charging IC)
- Dimensions – TBD
On the software side, Makerfabs mentions support for the ESP-IDF framework, the Arduino IDE, and PlatformIO, as well as the LVGL graphics library for designing complex, fluid user interfaces. The new 4G LTE ESP32-P4 display shares the same GitHub repository as the earlier “Matouch_ESP32-P4_TFT_with_Touch_10_1” without cellular connectivity. We could only find generic ESP-IDF samples and PDF schematics there, so if you want to use Arduino, you’re on your own… The documentation is also shared between the two displays; it includes a 4G LTE HTTP section explaining how to send AT commands to control the modem with the ESPBrookesia firmware.
The MaTouch ESP32-P4 10.1-inch MIPI HMI display development board with 4G LTE is sold on the Makerfabs store for $79.80. The board comes pre-installed in a basic enclosure, and the kit includes the 32GB MicroSD card.
Debashis Das is a technical content writer and embedded engineer with over five years of experience in the industry. With expertise in Embedded C, PCB Design, and SEO optimization, he effectively blends difficult technical topics with clear communication
Support CNX Software! Donate via cryptocurrencies, become a Patron on Patreon, or purchase goods on Amazon or Aliexpress. We also use affiliate links in articles to earn commissions if you make a purchase after clicking on those links.
