Category: Processors

Posted on by Jean-Luc Aufranc (CNXSoft) - 240 Comments on Giveaway Week – ESP32 PICO Kit v3 Boards

Giveaway Week – ESP32 PICO Kit v3 Boards

I don’t have one, but eight boards to give away to four winners (2 each) with Espressif Systems ESP32 PICO Kit v3 board based on ESP32-PICO-D4 SIP, an all-in one package with ESP32, 4MB SPI flash, crystal oscillator, and passive components, which allows for smaller boards. The board is very similar to any other ESP32 boards, and software compatible, but it’s just quite thinner, and easier to work with on breadboards. Since I had already played with Arduino Core and Espruino (JavaScript) on other boards, I used one of the 10 boards provided by Espressif to play with Micropyhon on ESP32. Each winner will get two ESP32 PICO Core board in order to make it worthwhile with regards to shipping costs. To enter the draw simply leave a comment below. Other rules are as follows: Only one entry per contest. I will filter out entries with the same IP and/or […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 6 Comments on SAMA5D2 Based SiPs Combine ARM Cortex-A5 Processor With Up to 128MB DDR2

SAMA5D2 Based SiPs Combine ARM Cortex-A5 Processor With Up to 128MB DDR2

Atmel SAMA5D2 ARM Cortex-A5 processor was released about two years ago with extended temperature range and lower power consumption compared to previous SAMAD5 processors, with the new SoC still targeting industrial Internet of Things (IIoT), wearables and point of sale applications. In recent years, we’ve seen companies packing main components into systems-in-package (SiP) with products such as Octavo Systems OSD3358 and Espressif Systems ESP32-PICO-D4 with integrate an existing processor with memory, storage, and/or PMIC. Microchip (previously Atmel) has now done the same for their SAMA5D2 processors with SiPs combining the Cortex A5 SoC with DDR2 memory. Four SAMA5D2 SiPs have been launched: ATSAMA5D225C-D1M based on ATSAMA5D22C MPU with extra SD/SDIO, QSPI, FLEXCOMs (2x), I2S, and timers (2x) and: 128 Mb (16 MB) DDR2 DRAM 90 Peripheral I/Os 196 BGA Package Designed for RTOS/bare metal development ATSAMA5D27C-D5M based on ATSAMA5D27C MPU with: 512 Mb (64 MB) DDR2 DRAM 128 Peripheral I/Os […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 6 Comments on $50 Waveshare Compute Module IO Board Plus is Designed for Raspberry Pi CM3/CM3L Compute Modules

$50 Waveshare Compute Module IO Board Plus is Designed for Raspberry Pi CM3/CM3L Compute Modules

Raspberry Pi Compute Module CM3L and CM3 are fairy inexpensive at $25 and $30 respectively, but if you want to get the complete development kit with Compute Module IO Board, CM3 and CM3L modules, and accessories you’ll need to spend around $150 plus shipping. A cheaper option might be Waveshare “Compute Module IO Board Plus for Raspberry Pi CM3, CM3L” with many of the same features as the original Compute Module IO board, plus some extras like terminal blocks for ADC/DAC or RTC battery, which I first found on DX for $49.95 including shipping. Waveshare Compute Module IO Board Plus specifications: Compute Module socket for Raspberry Pi CM3/CM3L I/O headers 40-pin Raspberry Pi GPIO header (3) GPIO header for all pins exposed by the modules (2) Arduino headers for shields (10) 10-bit ADC/16-bit DAC screw terminals (11) 3x 5-pin sensor interface (13) 1-WIRE interface, for connecting single-bus devices like DS18B20 […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 31 Comments on $15 Banana Pi M2 Zero Board is a Raspberry Pi Zero W Clone with a Quad Core Processor

$15 Banana Pi M2 Zero Board is a Raspberry Pi Zero W Clone with a Quad Core Processor

Many development boards have followed Raspberry Pi 2/3 form factor in recent years, including Hardkernel ODROID-C2 and Pine64 ROCK64, but so far I had not seen any boards leveraging Raspberry Pi Zero (W) form factor. SinoVoIP will change that, as they’ve just launched Banana Pi M2 Zero (aka BPI-Zero) board powered by Allwinner H2+ quad core processor, leveraging Raspberry Pi Zero W form factor, and now selling on Aliexpress for $15 plus shipping. Banana Pi M2 Zero specifications: SoC – Allwinner H2+ quad core Cortex A7 processor @ up to 1 GHz with Mali 400MP2 System Memory – 512 MB DDR3 Storage – micro SD card slot up to 64GB Video/Audio Output – mini HDMI Connectivity – 802.11 b/g/n WiFi and Bluetooth LE (AP6212 module with options for AP6181, AP6335) Camera – 1x MIPI CSI connector supporting 8-bit YUV422 CMOS sensor, CCIR656 protocol for NTSC and PAL, 5MP camera, 1080p […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 13 Comments on NanoPi Duo Quick Start Guide – Ubuntu, Breadboard, Mini Shield & mSATA SSD

NanoPi Duo Quick Start Guide – Ubuntu, Breadboard, Mini Shield & mSATA SSD

As far as I know NanoPi Duo is the only quad core ARM Linux development board that can fit on a breadboard. We’ve already seen it’s much smaller than Raspberry Pi Zero, and the company offer a mini shield exposing USB ports, Ethernet, a few I/Os, and an mSATA slot in in NanoPi Duo Starter Kit Review – Part 1: Unboxing and Assembly. I’ve finally played with it this week-end, and will report what I had to do to blink a LED when connected to breadboard, and my experience using the mini shield with  an mSATA SSD, WiFi connectivity, and cooling under load. Flashing Ubuntu 16.04.2 firmware image to NanoPi Duo As with many other Allwinner development boards, you should first check if Armbian is available for the board. NanoPi Duo is not supported, but it’s said to work with Orange Pi Zero image minus support for WiFi. Since the […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 179 Comments on Giveaway Week – NanoPi NEO NAS Kit with NEO 2 Board

Giveaway Week – NanoPi NEO NAS Kit with NEO 2 Board

Time has come to organize another giveaway week. I used to mainly give away TV boxes, but due to recent regulations that will not be possible anymore, and instead this giveaway week will include Linux and IoT development boards, and other accessories. I’ll start with NanoPi NEO NAS Kit v1.2. NanoPi NEO NAS Kit v1.2 is a low cost kit NanoPi NEO or NEO 2 board that takes a 2.5″ hard drive. I’ve tested it with NanoPi NEO 2 board and OpenMediaVault, and found to perform optimally for this type of device (USB 2.0 to SATA), with SAMBA reads & writes achieving 40 MB/s. The hardware given away includes the NAS Kit v1.2 and a NanoPi NEO 2 board. You’ll just need to add a micro SD card with the OMV image, a hard drive, and a 12V/2A (or greater) power supply. To enter the draw simply leave a comment […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 4 Comments on Intel Speech Enabling Developer Kit Works with Alexa Voice Service, Raspberry Pi 3 Board

Intel Speech Enabling Developer Kit Works with Alexa Voice Service, Raspberry Pi 3 Board

We’ve known Intel has been working on Quark S1000 “Sue Creek” processor for voice recognition for several months. S1000 SoC is based on two Tensilica LX6 with HiFi3 DSP, some speech recognition accelerators, and up to 8x microphones interfaces which allows it to perform speech recognition locally. The solution can also be hooked to an application processor via SPI, I2S and USB (optional) when cloud based voice recognition is needed. Intel has recently introduced their Speech Enabling Developer Kit working with Amazon Alexa Voice Service (AVS) featuring a “dual DSP with inference engine” – which must be Quark S1000 – and an 8-mic array. The kit also includes a 40-pin cable to connect to the Raspberry Pi 3 board. Intel only provided basic specifications for the kit: Intel’s dual DSP with inference engine Intel 8-mic circular array High-performance algorithms for acoustic echo cancellation, noise reduction, beamforming and custom wake word […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 2 Comments on Emcraft Releases Linux BSP for NXP i.MX RT1050 Cortex M7 Evaluation Board

Emcraft Releases Linux BSP for NXP i.MX RT1050 Cortex M7 Evaluation Board

NXP iMX RT series is a family of ARM Cortex M7 processors clocked at 600 MHz, making the solution a “crossover embedded processor” bridging the gap between real-time capabilities of micro-controllers and the performance of application processors. This week, NXP provided some benchmark numbers for i.MX RT1050 processor, which delivers a CoreMark score of 3020, DMIPS of 1284, and 20ns interrupt latency at 600 MHz, which means it could be a good candidate for embedded Linux, and Emcraft Systems has just released a uCLinux BSP for the NXP i.MX RT1050 EVK board. The BSP features U-Boot v2017.09-rc1, Linux Kernel 4.5 with relevant device drivers such as key I/O interfaces, Wi-Fi, SD card, LCD, etc…, and GNU development tools such as a GCC 4.7 toolchain, GDB, and so on. The company has made a demo with a GUI application designed with Crank Software’s Storyboard Suite, and running in Linux on the […]