Category: Processors

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on PocketCHIP Hackable & Portable Linux Game Console Can Be Pre-ordered for $49

PocketCHIP Hackable & Portable Linux Game Console Can Be Pre-ordered for $49

If you are interested in portable game consoles to run emulator, but can’t quite justify paying hundreds of dollars for device like Pyra or GPD Win, and Android game consoles don’t exactly fit your needs or match your expectations, PocketC.H.I.P based on the $9 C.H.I.P board, and part of the original Kickstarter campaign could be an interesting option, as it is now available for pre-order for $49. PocketCHIP specifications: SoC – Allwinner R8 Cortex A8 processor @ 1 GHz with Mali-400 GPU System Memory – 512 MB RAM Storage – 4GB NAND flash Display – 420 x 272 LED backlit display Keyboard – QWERTY keyboard Connectivity – 802.11 b/g/n Wi-Fi + Bluetooth 4.0 Video Output – 3.5mm jack for composite video and audio (HDMI and VGA available via adapters) USB – 1x USB host port, 1x micro USB OTG port Expansion – Through holes on the top giving access to […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 11 Comments on Olimex A20-OLinuXino-LIME2-eMMC Board Replaces NAND by eMMC Flash for Better Performance & Reliability

Olimex A20-OLinuXino-LIME2-eMMC Board Replaces NAND by eMMC Flash for Better Performance & Reliability

A20-OLinuXino-LIME boards are the most popular development board sold by Olimex, likely thanks to reasonable pricing, and Allwinner A20 is one of the rare low cost processor to features an actual SATA interface and Gigabit Ethernet support. The company has now launched a new version A20-OLinuXino-LIME2-eMMC, based on A20-OLinuXino-LIME2-4GB, but replacing the NAND flash by an eMMC flash that should offer both better performance and reliability. A20-OLinuXino-LIME2-eMMC specifications: SoC – Allwinner A20 dual-core ARM Cortex-A7 CPU @ 1.0 GHz  with dual-core Mali 400 GPU System Memory – 1GB DDR3 Storage – 4GB eMMC flash (Micron), SATA data and power connectors, micro SD slot, 2KB EEPROM for MAC address and custom data Connectivity – Gigabit Ethernet Video Output – HDMI up to 1080p60 USB – 2x USB 2.0 host ports with power control and current limiter, 1x micro USB-OTG with power control and current limiter Expansion – 160 GPIOs on four […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 8 Comments on Arduino UNO WiFi Board Combines Atmel ATmega328P MCU with ESP8266 SoC

Arduino UNO WiFi Board Combines Atmel ATmega328P MCU with ESP8266 SoC

Arduino.org (Arduino Srl) has launched Arduino UNO WiFi board, bringing Arduino (Atmel ATMega328P MCU) and ESP8266 together, and adding WiFi to the popular Arduino UNO board, while keeping all existing interfaces and headers. Arduino UNO WiFi (A000133) board specifications: Arduino part MCU – Atmel ATmega328 8-bit AVR MCU @ 16 MHz with 32 KB flash Memory, 2KB SRAM, 1KB EEPROM Digital I/O pins – 14, with 6 PWM and UART Analog Input Pins – 6 DC Current per I/0 –  40 mA Misc – Reset button Operating Voltage – 5 V ESP8266 part SoC – Expressif ESP8266EX Tensilica Xtensa LX106 processor @ 80 MHz Storage – 4MB SPI flash Connectivity – 802.11 b/g/n WiFi @ 2.4 GHz, wake up time < 2 ms; Antenna: PCB and IPX Misc – Bootloader button, WiFi LED Operating Voltage – 3.3 V Common specs USB – 1x USB device port Input Voltage – 5-12 […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on Orbitty is a $175 Carrier Board for Nvidia Jetson TX1 System-on-Module

Orbitty is a $175 Carrier Board for Nvidia Jetson TX1 System-on-Module

Connect Tech had already launched Astro carrier board for Nvidia Tegra X1 based Jetson TX1 CPU module, which they also integrated into Rosie Military Grade Embedded mini PC. Since them the Canadian company had also introduced a low cost “Elroy” carrier board , and more recently, a third cheaper baseboard called Orbitty selling for  $175 and up, and including Gigabit Ethernet, USB 3.0 & 2.0 ports, HDMI, and more. Orbitty (ASG003) carrier board specifications: Compatibility – Nvidia Jetson TX1 system-on-module Storage – micro SD slot Video & Audio Output – 1x HDMI Connectivity – Gigabit Ethernet (RJ45) USB – 1x USB 3.0 port, 1x micro USB 2.0 OTG port Expansion Header – 20-pin header with 2x 3.3V UART, I2C, 4x GPIO, etc… Power Supply – 9 to 19V DC via terminal block Dimensions – 87 x 50mm Operating Temperature – -40°C to +85°C The carrier board targets robotics and unmanned […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 26 Comments on Pyra Open Source Debian Handheld Computer & Game Console is Now Available for Pre-order

Pyra Open Source Debian Handheld Computer & Game Console is Now Available for Pre-order

The development of Pyra open source portable gaming console started in 2014, and after over two years of hard work, the developers are now ready to take pre-order of the Texas Instruments OMAP 5 powered device running Debian Linux. Pyra handheld specifications have changed a little bit since the announcement two years ago: SoC – Texas Instruments OMAP 5432 SoC with 2x ARM Cortex-A15 @ 1.7Ghz with NEON SIMD, 2x ARM Cortex-M4, Imagination Technologies PowerVR SGX544-MP2 GPU for 3D graphic, and Vivante GC320 GPU for 2D graphics System Memory – 2GB or 4GB RAM Storage – 32 GB eMMC flash, 2x SDXC card slot, 1x internal micro SDXC card slot Display – 720p 5″ LCD with resistive touchscreen Video Output – micro HDMI Audio I/O – High-quality speakers, analog volume wheel, headset port, built-in Mic Gaming controls – D-Pad, 4x shoulder buttons, 6x face buttons, 2x accurate analog controls with […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 1 Comment on Wandboard Development Boards Get Android 6.0 Marshmallow Support

Wandboard Development Boards Get Android 6.0 Marshmallow Support

Wandboard development boards powered by Freescale i.MX6 Solo, Dual and Quad Cortex A9 processors were released over 3 years ago with Android 4.1 Jelly Bean. Contrary to many other boards that don’t get an updated version, Wandboard boards got support for Android 4.4 Kitkat, Android 5.x Lollipop, and now the community has recently released Android 6.0 Marshmallow. You can try the Android 6.0 SD card image as follows:

Where /dev/sdX is the device for your SD card. If you can remember the first Jellybean release had separate images for each version of the board, but thanks to device tree implementation, a single image is now released with all three versions. The full source code is also available in a 5.0 GB tarball. Since Freescale, now NXP, i.MX6 processors will be available until November 2022, we can most probably expect a few more Android releases for the board. Jean-Luc Aufranc […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 5 Comments on Electrodragon WiFi IoT Relay Includes ESP8266 Module, AC Power, and Enclosure for $6

Electrodragon WiFi IoT Relay Includes ESP8266 Module, AC Power, and Enclosure for $6

Thanks to ESP8266, the cost of WiFi relays has dramatically come down, but so far, I could not find an all-in-one solution with ESP8266, relay, AC power and enclosure, and for example I’m still using NodeMCU board, a relay board, a USB power supply, and put all that into a plastic jar in order to control a water pump. It works but it’s not ideal, and solutions like Wemos D1 mini with relay shield improves things further, but Electrodragon has come with a connect-and-play WiFi IoT relay that integrates everything including the case for $6 + shipping. Wifi IoT Relay Board Based on ESP8266: WiFi module – ESP-12F based on Espressif ESP8266EX WiSoC Relays – 2x Songle SRD-05VDC-SL-C relays supporting 125VAC/10A, 250VAC/10A, 30VDC/10A, 28VDC/10A Input/Output – 3x terminal blocks for relay and power Expansion – 12-pin header with Rx/Tx,  GPIO4, Btn2, GPIO15, 5V/GND,  ADC, GPIO5, Btn1, OUTPUT1, and 3V3 Debugging […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 24 Comments on Setup Guide & Mini Review of BQ Aquaris M10 Ubuntu Edition Tablet from a Developer’s Perspective

Setup Guide & Mini Review of BQ Aquaris M10 Ubuntu Edition Tablet from a Developer’s Perspective

BQ Aquaris M10 UBuntu Edition is the first officially supported Ubuntu tablet on the market. Blu, a frequent commenter on this blog, has purchased the Full HD version, and in the guest post below, shares his experience setting up the device for development purpose, before shortly providing his overall impressions about the tablet itself. Quick introduction Ever since I had to retire my trusty-but-ancient ARM notebook (a Genesi Efika iMX51) I’ve been looking for a new ARM notebook or perhaps a 2-in-1 device, that I could use for development on the go. The basic requirements are long battery life, passive cooling and reasonable price. Also, Just Enough Power™ for running vim, a couple of toolchains (gcc/clang with gold) and, well, enough grunt to run my coding experiments. Naturally, BQ M10 Ubuntu Edition immediately got my attention to the extent of me placing an order, which got delivered this past week. […]