diy News - Page 10 of 14 - CNX Software

February 4, 2019 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Spare TV Box Board Sold for MXQ-4Q / MXQPro DIY Repairs

Once somebody asked me if spare TV box boards were available for purchase since his TV box died after a few months, and he wanted to repair it himself without having to purchase another complete TV box. Usually, such boards are not sold, except maybe on Alibaba, where you may or may not have to purchase in quantities. So I basically told him it would be hard to find, and buying a new or second hand TV box would be a better option. But I was recently made aware that at least one seller was offering spare TV box boards for MXQ-4Q and MXQPro on Aliexpress for $20.61 shipped in order to let people repair their boxes themselves. If your goal is to repair a TV box, I can only think of two reasons for buying a spare TV box board: saving money and/or reducing electronics waste. MXQ-4Q and MXQPro […]

January 15, 2019 by Jean-Luc Aufranc (CNXSoft) - No Comments

XinaBox’s xChips Enable Modular Electronics for Makers & STEM Education

So today, I decided to have a look a 96Boards website to see if there was anything new from the community, and I came accross “X in a Box B901“, an “☒CHIP is designed to interface with the 96 Boards, such as the Dragonboard 410c. This provides an interface to support the ☒CHIP ecosystem, adding support for many additional sensors etc…” I had no idea what it was all about, so obviously I had to investigate. Xinabox (X in a Box) is an ecosystem of modular electronics boards used for developing, making products and learning. There are now over 70 modular xChip” with cores/CPUs, sensors, power, communication, output, and storage. They are interconnected together without wires, soldering, breadboards, and adapters are provided for Raspberry Pi, 96Boards, and other development boards. xChips can be sorted into 8 categories: Cores – MCU/CPI cores based on Microchip ATMega328P, SAMD21, ESP8266, or ESP32 with […]

December 4, 2018December 4, 2018 by Jean-Luc Aufranc (CNXSoft) - 17 Comments

Up2Stream WiFi Audio Receiver Module Targets DIY Wireless Speakers

If you own a set of very good speakers, and are interested in making them smarter, Arylic Up2Stream WiFi audio receiver module may be a solution to look into. The module allows to make your own DIY wireless speakers by adding WiFi connectivity, and features such as multiroom, AirPlay, DLNA streaming, Spotify, and Internet radio streaming. Up2Stream (WA31) hardware specifications: SoC – MediaTek MT7688AN MIPS processor @ up to 580 MHz System Memory – 64MB DDR2 Storage – 16MB flash Connectivity – 2.4GHz 802.11 b/g/n 1T1R WiFi up to 150 Mbps with 5 dBi I-PEX antenna Audio – 24-bit / 192 KHz decoding, 20 Hz – 20KHz frequency range, 4-pin speaker connector with 2.0mm pitch USB – 1x USB 2.0 port port Power Supply – 5VDC / 1A via 2-pin header (2.0mm pitch) Power Consumption – 160 to 320 mA Dimensions – 55.21 x 41.37mm The module ships with a […]

October 26, 2018October 26, 2018 by Jean-Luc Aufranc (CNXSoft) - 10 Comments

$94 MAKERphone DIY Mobile Phone Supports MicroPython, Arduino IDE, and Scratch (Crowdfunding)

If you ever wanted to buy a mobile phone that you can assemble yourself, RePhone Kit Ctreate going for $59 is a nice option, but in truth it does not exactly look like your typical phone with its almost square shape. It’s also good to have more option, that’s exactly what MAKERphone is offering with a DIY mobile phone targeting the educational market. Beside the educational value of the assembly also involving some soldering skills depending on the selected kit, kids will be able to learn to program the phone with MicroPython, the Arduino IDE (C language), and/or Scratch visual programming. MAKERphone kit content and specifications: MAKERphone circuit board with 8x user LEDs for backlight (and special effects), 4-way mechanical joystick, 12-button numeric keypad, A, B, C, D, E, and F buttons, DS3231 RTC chip, vibrator… Main microcomputer module based on Espressif Systems ESP32 WiSoC with 802.11 b/g/n WiFi, Bluetooth […]

September 19, 2018June 19, 2019 by Karl Johnson - 33 Comments

Genmitsu CNC 3018-PRO CNC Router Review – Part 1: Build & First Etches

Hey Karl here. Today we are going to look at something a little different. I am writing about my experiences with building Genmitsu 3018 CNC router upgraded version provided by Sainsmart for this review. While waiting on the unit to arrive I did some research and found that there are several different versions on the market labeled CNC xxxx. The xxxx represent the build volume in the x and y. So the one I was sent has a 300x180mm build volume. The 3018 is called upgraded because the new mounting for the X and Y rods and lead screws. On the previous version these had to be mounted and manually aligned which from what I read can be a pain. Building Genmitsu CNC 3018-PRO CNC Router The build went very well. The 3018 user manual was mostly pictures but they called out anything that might be questionable. I had been […]

September 8, 2018September 8, 2018 by Jean-Luc Aufranc (CNXSoft) - 9 Comments

How to Make a Low Cost DIY SD Card Duplicator

If you have to duplicate many SD cards for example to boot Raspbian on multiple Raspberry Pi board, one option is buy one of those SD card duplicators, but the problem is that they are not really cheap, for example the Systor 1-to-7 cards model sells for $540. Bob Brown, a retired senior lecturer, is now teaching K-12 students how to get started with Raspberry Pi boards, and must prepare bootable SD cards for his class. In order to save time, a duplicator would have been nice, but the price is too high, so instead he went with a DIY solution. You’ll first need some hardware, including a powered USB hub with the number of cards you want to duplicate, and corresponding SD card reader, and a larger micro SD card to hold Raspbian and/or other operating systems (optional, only for Raspberry Pi based duplicator). Mr. Brown made a 10-port […]

July 30, 2018July 30, 2018 by Jean-Luc Aufranc (CNXSoft) - 9 Comments

Raspberry Pi 3 based Retro Arcade Game Console Sells for under $250

When it comes to retro-gaming for the Raspberry Pi 3 board, there’s no lack of option with firmware like RetroPie or Lakka, a few off-the-self accessories like USB or Bluetooth gamepad, a an HDMI monitor, you can get started in no time. However, if you want to make a retro arcade game console, it may take some more efforts, as you’d normally have have to design the case yourself, source the buttons and controls, the display, extra electronics and so on. But the “DIY classic retro arcade game console” based on Raspberry Pi 3 board currently sold on Banggood for $247.99 should make things much easier, as it’s supposed to be plug and play, while still offering the option to add or remove games, and mess around with the hardware if you wish to. Banggood did not provide the full technical details, but here’s what we know about the specifications: […]

July 11, 2018July 11, 2018 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

This Soldering Pen Board with Audio Jack Supports Weller RT Tips

The 3.5mm audio jack may be slowly disappearing from new mobile phones, but I’ve recently discovered they were also used in some soldering irons such as the upcoming TS80 USB soldering iron succeeding TS100 model. I initially thought it was a custom design from the maker of TSxxx soldering irons, but this morning I’ve come across the “RT Soldering Pen” board which also features a 3.5mm (audio) jack and can be used to make your own soldering iron by 3D printing your own enclosure, adding some power source, and inserting one of the many Weller RT tips available into the jack. RT soldering pen board specifications: MCU – STMicro STM32F031 Arm Cortex-M0 micro-controller Display – 0.91″ OLED display with 128×32 resolution Compatible with all Weller RT tips with 3.5mm jack. Set-point temperature – 20°C – 400°C with about +/-5°C accuracy (calibration is planed) Maximum measurable temperature – 500°C Heating speed […]