Elfin-EW11 is a compact WiFi to RS485 unit with Modbus TCP support

Elfin EW11 Wifi to RS485 unit

Elfin EW11/EW11A is a small WiFi to RS485 unit with Modbus TCP/IP support that works either in the 5 to 18V DC (EW11) or the 5 to 36V DC (EW11A) input range. The WiFi to RS485 adapter is offered with either an internal or external WiFi antenna, the RS485 interface is exposed through an RJ45 port, and an RJ45 to terminal block cable is usually included, as well as a DIN Rail mount. Elfin EW11/EW11A specifications: MCU (I’m not sure which one is used, and the specs depend on where you look..) Unnamed Arm Cortex-M3 microcontroller @ 96 MHz with 2MB flash, 128KB SRAM (on the product page) OR Unnamed microcontroller @ up to 160MHz with 2MB flash, 352KB SRAM (on Aliexpress) Networking Wireless  – 2.4 GHz WiFi 4 with up to WPA2PSK security, station, AP, or station+AP modes; internal or external WiFi antenna depending on the model. Wired – […]

Arduino-programmable EtherCAT master runs FreeDOS on Vortex86EX2 x86 processor

EtherCAT Master RS485 Arduino

ICOP QEC-M-01 is an EtherCAT master system running FreeDOS based on DM&P Vortex86EX2 dual-core x86 processor. It is programmable with an industrial Arduino IDE – the 86Duino IDE – that supports an EtherCAT API for real-time field monitoring and big data collection. The system can be used for industrial automation applications that require precise timing and it can monitor the hardware’s voltage, current, and temperature to calculate/estimate carbon emissions for industrial manufacturing to assist in the tracking of a factory’s carbon footprint. ICOP QEC-M-01 specifications: SoC – DM&P Vortex86EX2 dual-core processor with the Master core clocked up to 600MHz and the Slave core up to 400MHz System Memory – 1GB or 2GB DDR3 Storage – 32MB SPI Flash, MicroSD card, optional eMMC flash Networking Gigabit Ethernet RJ45 port 2x 10/100Mbps Ethernet RJ45 ports for EtherCAT master with support for CANopen over EtherCAT (CoE), File Access over EtherCAT (FoE), Distributed Clocks […]

Raspberry Pi CM4 based 7-inch industrial Panel PC takes IO board with RS232, 12V-24V inputs and outputs

Raspberry Pi CM4 industrial panel PC

The ComfilePi CPi-C070WR4C is a 7-inch industrial Panel PC powered by a Raspberry Pi CM4 module with GPIO, RS-232, RS-485, and I2C interfaces as well as the ability to add two more RS232 interfaces and several 12V-24V DC inputs and outputs through an I/O board connected to the GPIO port of the panel PC. The new panel PC is an update to the ComfilePi Industrial Touch Panel PC introduced with a Raspberry Pi CM3 module in 2017. Besides upgrading to a more powerful Raspberry Pi Compute Module 4,  COMFILE also makes use of an RS-485 port that utilizes a full UART interface that does not exhibit the limitations of the mini-UART interface, and also added the CP-IO13-4C I/O board for even more expansion capabilities. ComfilePi CPi-C070WR4C specifications: SoM – Raspberry Pi Compute Module 4 with SoC – Broadcom BCM2711 quad-core Arm Cortex-A72 processor @ 1.5GHz with VideoCore Vi GPU supporting […]

EDATEC CM4 Industrial – An Raspberry Pi CM4 computer for IIoT, automation, and industrial control

EDATEC Raspberry Pi CM4 Industrial Computer Carrier board

EDATEC CM4 Industrial is both a Raspberry Pi CM4 carrier board and a computer for industrial IoT, control, and automation that expands on the company’s CM4 Sensing and CM4 Nano solutions with more features and interfaces. The system notably offers two RS485, one RS232, three analog inputs, two digital inputs, and one relay output through terminal blocks, as well as optional WiFi, Bluetooth, and 4G LTE + GPS connectivity, and a wide DC voltage range of 8V to 36V. EDATEC CM4 Industrial specifications: SoM – Raspberry Pi CM4 module with SoC – Broadcom BCM2711 quad-core Arm Cortex-A72 processor @ 1.5GHz with VideoCore Vi GPU supporting OpenGLES 3.1, Vulkan 1.x, H.265 (HEVC) (up to 4Kp60 decode), H.264 (up to 1080p60 decode, 1080p30 encode) System Memory – 1GB, 2GB, 4GB, or 8GB LPDDR4-3200 SDRAM Storage Optional 8GB/16GB/32GB eMMC flash for system boot MicroSD card slot for booting the system on a Raspberry […]

LILYGO T-RSC3 ESP32-C3 board features isolated RS232 & RS485 interfaces, 5 to 24V DC input

ESP32-C3 board with RS232 and RS485

LILYGO T-RSC3 is a relatively compact ESP32-C3 board with WiFi 4 and Bluetooth LE 5.0 connectivity, support for RS232 and RS485 communication protocols through a DB9 connector and a terminal connector respectively, and a wide 5V to 24V DC power input. LILYGO had already made an ESP32 board with CAN Bus and RS485 interfaces called the T-CAN485, but without any isolation. The new T-RSC3 offers both RS232 and RS485 interfaces, but no CAN Bus, protected by isolated transceiver modules that should make it safer to use in industrial environments. LILYGO T-RSC3 board specifications: Wireless module – Espressif Systems ESP32-C3-MINI-1U module with ESP32-C3 RISC-V microcontroller @ 160 MHz with 400 KB SRAM, 2.4 GHz WiFi 4, Bluetooth 5.0 LE & Mesh, 4MB flash, and a u.FL antenna connector Industrial control interfaces RS232 via DB9 connector, RSM232MT5V isolated transceiver with 3000V isolation, 4.75~5.25V input, 5V/50mA output, baud rate from 1200 to 256,000 […]

UP Xtreme i12 Edge mini PC features Alder Lake-P SoC up to Intel Core i7-1270PE

UP Xtreme i12 Edge mini PC

AAEON has just launched the UP Xtreme i12 Edge mini PC based on the company’s UP Xtreme i12 SBC equipped with an Intel Core i7-1270PE and other Alder Lake processors, up to 32GB LPDDR5 memory, and support for two M.2 NVMe SSD as well as SATA storage The Xtreme i12 Edge is the successor of the Xtreme i11 Edge Compute Enabling Kit powered by a choice of Intel Tiger Lake processors. It also comes with 2.5GbE and GbE networking, one USB4 port, several USB 3.2 Gen2 ports, HDMI and DisplayPort video outputs, plus some COM ports and a terminal block for GPIOs. UP Xtreme i12 Edge mini PC specifications: Alder Lake-P SoC (One or the other) Intel Core i7-1270PE 12-core/16-thread processor @ 3.30GHz / 4.50GHz (Turbo) with 96EU Intel Xe graphics – PBP: 28W, up to 64W MTP Intel Core i5-1250PE 12-core/16-thread processor @ 3.20GHz / 4.40GHz (Turbo) with 80EU […]

EDATEC CM4 Sensing industrial computer offers CAN bus, RS485, and RS232 interfaces

Edatec CM4 Sensing

EDATEC CM4 Sensing is a compact industrial computer based on the Raspberry Pi Compute Module 4 (CM4) with multiple RS485, RS232, and CAN bus interfaces, an HDMI port, two USB ports, Gigabit Ethernet, and optional WiFi, Bluetooth, and/or 4G LTE connectivity. The industrial mini PC can operate in the -25 to 70°C temperature range, supports 8 to 28V DC wide voltage input, includes an RTC, and the single board computer also features a MIPI DSI interface to connect the official Raspberry Pi 7-inch display as well as an FPC interface with HDMI and USB touch.   EDATEC CM4 Sensing specifications: SoM – Raspberry Pi CM4 module with Broadcom BCM2711 quad-core Cortex-A72 SoC, 1GB to 8GB LPDDR4 RAM, and up to 32GB eMMC flash Storage – MicroSD card socket for data storage. It can work with the eMMC flash on the CM4 module Display I/F 1x HDMI 2.0 Type-A port up […]

Forlinx FET-MX9352-C – An NXP i.MX 9352 system-on-module for industrial AIoT applications

Forlinx FET-MX9352-C System-on-Module

Forlinx FET-MX9352-C is a system-on-module based on NXP i.MX 9352 dual Cortex-A55 processor with Cortex-M33 real-time core and a 0.5 TOPS AI accelerator that can be used for industrial control, IoT gateways, medical equipment, and various applications requiring machine learning acceleration. The FET-MX9352-C follows last week’s announcement of the iWave Systems iW-RainboW-G50M OSM module and SBC with a choice of NXP i.MX 93 processors. The Forlinx module comes with two board-to-board connectors instead of solderable pads and can be found in the OK-MX9352-C single board computer with dual GbE, various display and camera interfaces, RS485 and CAN Bus, etc… FET-MX9352-C i.MX 9352 system-on-module Specifications: SoC – NXP i.MX 9352 with 2x Arm Cortex-A55 cores @ up to 1.7GHz (commercial) or 1.5 GHz (industrial), Cortex-M33 real-time core @ 250 MHz, 0.5 TOPS Arm Ethos U65 microNPU System Memory – 1GB/2GB LPDDR4 RAM Storage – 8GB eMMC flash 2x high-density 100-pin board-to-board […]

EDATEC Raspberry Pi 5 fanless case