solar News - CNX Software - Embedded Systems News

April 19, 2024 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

ESP32-S3 PowerFeather board supports up to 18V DC for solar panel input

The ESP32-S3 PowerFeather board is an Adafruit Feather-shaped ESP32-S3 WiFi and BLE IoT board that can be powered by a Li-Ion or LiPo battery and supports up to 18V DC input for direct connection to a solar panel. The developer told CNX Software that the main differentiating factor from other ESP32-S3 development boards was “its extensive power management and monitoring features” with a wide DC input range, supply and battery monitoring, and battery protection features. ESP32-S3 PowerFeather specifications: ESP32-S3-WROOM-1-N8R2 MCU – ESP32-S3 dual-core Tensilica LX7 up to 240 MHz with 512KB SRAM, 16 KB RTC SRAM Memory – 2MB QSPI PSRAM Storage – 8MB QSPI flash Wireless – WiFi 4 and Bluetooth 5 LE + Mesh; PCB antenna USB – 1x USB-C 1.1 OTG port for power and programming Expansion 2x 16-pin 2.54 mm pitch headers with 23x multi-function GPIO: UART, I2C, SPI, I2S, SDIO, PWM, CAN, RMT, Camera, LCD […]

February 6, 2024February 6, 2024 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

Solar power manager module supports 6V-24V input range, battery charging, MPTT function, and outputs 5V/3A

Waveshare Solar Power Manager Module (D) is a compact power module for solar panels with support for 6V to 24V input, MPTT (Maximum Power Point Tracking), and battery charging. It outputs 5V up to 3A via a USB-C port or terminal block and should be suitable for a range of projects. A few weeks ago, we wrote about the FireBeetle 2 ESP32-C6 IoT development board with DFRobot highlighting support for solar charging of lithium batteries thanks the the CN3165 chip. But with a range of just 4.5 to 6V for solar panel input and a lack of support for MPTT, several readers were unimpressed by the solution. The Waveshare Solar Power Manager Module (D) recently popped up in my news feed, and I thought it might be worth a look. Waveshare Solar Power Manager Module (D) specifications: Solar panel input 6V to 24V via DC jack or 2-pole screw terminal […]

January 20, 2024January 21, 2024 by Debashis Das - 14 Comments

This new ESP32-C6-based IoT development board supports solar battery charging

FireBeetle 2 ESP32 C6 IoT Development Board with Wi Fi 6, Bluetooth 5, Solar Powered

DFRobot’s FireBeetle 2 ESP32-C6 is an IoT Development Board with 802.11ax (now called Wi-Fi 6), Bluetooth 5, Zigbee 3.0, Thread 1.3, and flexible power options including USB Type-C, 5V DC, and a CN3165 Lithium Ion battery charger for solar-powered systems. This isn’t the first solar-based board we’ve covered. We’ve also explored boards like Conexio Stratus, Wisblock Kit 2, and RAK8211-NB iTracker along with other solar-powered devices such as solar-powered laptops, solar-powered headphones, and even a solar-based power supply. FireBeetle 2 ESP32-C6 IoT Development Board Specifications: Processor – ESP32-C6 RISC-V single-core, 160 MHz Memory SRAM – 512KB ROM – 320KB Flash – 4MB RTC SRAM – 16KB USB – USB 2.0 CDC Wi-Fi Protocols – IEEE 802.11b/g/n, IEEE 802.11ax (20 MHz-only non-AP mode) Bandwidth – Supports 20 MHz and 40 MHz at 2.4 GHz Modes – Station, SoftAP, SoftAP+Station Frequency – 2.4GHz Frame Aggregation – TX/RX A-MPDU, TX/RX A-MSDU Bluetooth Protocol […]

January 12, 2024 by Jean-Luc Aufranc (CNXSoft) - No Comments

Reolink Argus PT Ultra review – A solar powered 4K WiFi Pan-and-Tilt smart security camera

Reolink Argus PT Ultra Solar Panel Instllation

Nearly four years ago, I reviewed the solar-powered Reolink Argus PT pan-and-tilt security camera. The device worked (and still works) mostly fine, but it was at a time when security cameras did not implement AI features like people and vehicle detection just yet relying only on PIR motion sensors so I’d get plenty of false positives. The WiFi connection is not overly reliable either especially when I tried to access the camera from outside my house, something that does not happen with the PoE and 4G LTE models from the company. Reolink asked me whether I wanted to review the new Reolink Argus PT Ultra security camera with higher 4K resolution, dual-band WiFi support, as well as people, vehicle, and pet detection, and most of the same other features found on the older Argus PT. So I took up on the offer and I’ve used it for about one month […]

April 22, 2023April 23, 2023 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

HARDWARIO CHESTER – A configurable Zephyr OS LPWAN IoT gateway with LoRaWAN, LTE IoT, GNSS connectivity

HARDWARIO CHESTER platform is a configurable LPWAN IoT gateway whose main function is to connect as many devices and environments as possible to the Internet using connectivity such as LoRaWAN, LTE Cat M1, or NB-IoT, as well as GNSS for geolocation. Contrary to most IoT gateways, it does not run Linux on an application processor, and instead, the “brain” of the CHESTER IoT gateway is a Raytac Bluetooth 5.0 module based on a Nordic Semi nRF52840 Arm Cortex-M4 microcontroller running Zephyr real-time operating system, which connects to LTE IoT modem and a LoRaWAN module through UART, and expansion modules through I2C, 1-wire, and GPIO interfaces. HARDWARIO CHESTER specifications: Wireless modules/chips Raytac MDBT50Q-P1MV2 Bluetooth 5.0 module based on Nordic Semi nRF52840 Arm Cortex-M4F MCU with 1MB Flash memory, 256kB RAM Nordic Semi nRF9160-SICA-B1A-R7 LTE-M/NB-IoT system-in-package (SiP) with Arm Cortex-M33 MCU, 1024 KB flash, 256 KB SRAM Murata CMWX1ZZABZ-078 LoRa module as […]

September 5, 2022September 5, 2022 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

Telink energy harvesting wireless module to enable batteryless remote controls

Telink Energy Harvesting Multi protocol Wireless module TV remote control

Telink TLSR8273-M-EH is a multi-protocol wireless connectivity module with energy harvesting capabilities implemented through Nowi’s PMIC, and designed for batteryless devices (or ones with “forever batteries”) such as TV remote controls, but also wearables, and electronic shelf labels among others. The solution is based on a 48MHz RISC microcontroller that supports Bluetooth 5.1 LE, 802.15.4 (Zigbee/RF4CE/6LoWPAN/Thread), and 2.4GHz proprietary protocols. With a single module integrating all main components required for batteryless operation, Telink says its solutions reduce BOM and size, as well as supply chain complexity, and improves user-friendliness by removing the need for battery swaps. Telink TLSR8273-M-EH specifications: Core – 32-bit RISC microcontroller @ up to 48 MHz (CoreMark 1.25/MHz) Memory – 64 KB SRAM with 32 KB retention Storage – 512 KB flash RF Bluetooth 5.1 LE up to 2 Mbps, with AOA/AOD support, Bluetooth Mesh IEEE 802.15.4 radio for Zigbee, RF4CE, 6LoWPAN, Thread 2.4GHz proprietary protocols RX […]

July 25, 2022July 27, 2022 by Jean-Luc Aufranc (CNXSoft) - No Comments

RAKwireless introduces WisBlock modular power supply, IP65 enclosures, and more sensor modules

RAKwireless Wisblock modular IoT prototyping system will get new modules about once every quarter and the latest Wisblock Summer 2022 event brings some RAK190xx base boards and power modules to support various power sources from solar panels to PoE, two IP65-rated “Unify” enclosures, as well as four new Wisblock sensor modules. Wisblock RAK190XX base boards and power modules The company has launched three base boards designed to take one of the five Wisblock power modules: RAK19009 – A small (47×30 mm) base board with only 2 sensor slots. RAK19010 – The “standard” base board with 4 sensor slots and 1 I/O slot RAK19011 – Version of the Dual IO base board with a power slot RAK19012 – WisBlock power module with USB, battery, and solar panel supply RAK19013 – WisBlock power module for rechargeable batteries and solar panel supply without the USB, for applications where you do not want to […]

June 27, 2022 by Jean-Luc Aufranc (CNXSoft) - 13 Comments

ESP32 board with 150Mbps 4G LTE modem also supports RS485, CAN Bus, and relay expansion

LILYGO has designed another ESP32 board with a 4G LTE modem with the LILYGO T-A7608E-H & T-A7608SA-H variants equipped with respectively SIMCom A7608SA-H for South America, New Zealand, and Australia, and SIMCom A7608E-H for the EMEA, South Korean, and Thai markets, both delivering up to 150 Mbps download and 50 Mbps upload speeds. The board also supports GPS, includes a 18650 battery holder, and features I/O expansion headers that support an add-on board with RS485 and CAN bus interfaces, in a way similar to the company’s earlier TTGO T-CAN485 board with ESP32, but no cellular connectivity. LILYGO T-A7068E-H/T-A7608SA-H board specifications: Wireless Connectivity WiFi & Bluetooth – ESP32-WROVER-E module based on ESP32 dual-core processor @ 240 MHz with 4MB flash, 8MB PSRAM, 2.4 GHz WiFi 4 and Bluetooth 4.2/5.x connectivity, PCB antenna Cellular connectivity Data transfer speeds 4G LTE – Up to 150 Mbps downlink, up to 50Mbps uplink 3G HSPA+ […]