You searched for Stamp - CNX Software

Stamp P4 (Left) Stamp AddOn C6 For P4 (Right)

March 29, 2026March 28, 2026

M5Stack Stamp-P4 – A tiny ESP32-P4 USB-C board with optional Wi-Fi 6 and Bluetooth 5.4

M5Stack has just introduced the Stamp-P4, a tiny USB-C development board built around the ESP32-P4 high-performance RISC-V MCU chip, featuring 16MB of Flash and 32MB of PSRAM, and optional Wi-Fi 6 and Bluetooth 5.4 support through the ESP32-C6-MINI-1-based Stamp-AddOn C6 module. Despite its small size (29.8 x 22.0 x 4.3mm), the Stamp-P4 offers a wide range of interfaces, including a MIPI-CSI camera connector, as well as a MIPI DSI display interface, RMII Ethernet, USB 2.0 HS, and up to 44x GPIOs via 1.27mm/2.00mm pitch castellated holes and a few through holes. M5Stack Stamp-P4 specifications: SoC – Espressif Systems ESP32-P4NRW32 CPU Dual-core RISC-V microcontroller @ 360 MHz with AI instructions extension and single-precision FPU Single-RISC-V LP (Low-power) MCU core @ up to 40 MHz GPU – 2D Pixel Processing Accelerator (PPA) VPU – H.264 and JPEG codecs support Memory – 768 KB HP L2MEM, 32 KB LP SRAM, 8 KB TCM, 32MB […]

March 16, 2026March 15, 2026

M5Stamp C6LoRa tiny (18×15×2.3 mm) SMD module pairs ESP32-C6 with SX1262 LoRa chip

The M5Stamp C6LoRa is a compact LoRa SMD module that combines the ESP32-C6 Wi-Fi 6, Bluetooth LE, and 802.15.4 microcontroller with the SX1262 LoRa transceiver for both high-speed and long-distance communication. The module targets applications such as smart agriculture, remote meter reading, industrial monitoring, and outdoor long-range wireless control systems. The module measures 18 × 15 × 2.3 mm, making it suitable for space-constrained systems and compact embedded designs. M5Stack has also added an SGM13005L4 low-noise amplifier (LNA) to improve reception performance, along with a PI4IOE5V6408 I/O expander that manages the LoRa control signals without using too many of the ESP32-C6’s GPIO pins. M5Stamp C6LoRa specifications: SoC – Espressif Systems ESP32-C6 CPU Single-core 32-bit RISC-V clocked up to 160 MHz Low-power RISC-V core @ up to 20 MHz Memory/Storage – 512KB SRAM, 320KB ROM Wireless – WiFi 6, BLE 5.3, 802.15.4 (See wireless section) Storage – 16 MB external NOR flash […]

RP2350 Tiny and Tiny XL boards clone Solder Party’s RP2350 stamp layouts at nearly half the price

While searching Aliexpress, I stumbled upon the RP2350 Tiny and Tiny XL, both of which are RP2350-based low-cost stamp-size development boards that look exactly like the Solder Party’s “RP2350 Stamp” modules, but are available at nearly half the price. Both modules feature the Raspberry Pi RP2350 dual-core Arm Cortex-M33 microcontroller and an integrated LiPo charging circuitry. The RP2350 Tiny offers 30x GPIOs, while the larger RP2350 Tiny XL breaks out 48x GPIOs, adds PSRAM, and includes SWD/UART JST connectors. Key interfaces include USB host/device, UART, SPI, I²C, PWM, ADC, and PIO state machines, along with Secure Boot and Arm TrustZone. These features make this board suitable for rapid prototyping and testing with CircuitPython support. RP2350 Tiny and Tiny XL specifications: Microcontroller RP2350 Tiny – Raspberry Pi RP2350A MCU, QFN-60; 7×7 mm RP2350 Tiny XL – Raspberry Pi RP2350B MCU,QFN-80; 10×10 mm Memory – 520KB internal RAM, 8KB OTP storage Storage – 16MB […]

July 11, 2025

M5Stack Stamp-S3A WiFi and BLE IoT module benefits from optimized antenna design, lower power consumption

M5Stack Stamp-S3A, also known as M5StampS3A, is an update to the M5Stamp S3 ESP32-S3 module introduced in 2023 with an optimized antenna design, lower power consumption, a larger user button, and a different logic for the RGB LED control. Other features remain the same with 8MB Flash, RGB LED, input button, and 23 GPIOs all in a tiny 26 x 18mm form factor. Two versions are available: the Stamp-S3A without pre-soldered headers and the Stamp-S3A PIN1.27 with headers soldered on the board and an orange heat-resistant cover. M5Stamp-S3A specifications: WiSoC – Espressif Systems ESP32-S3FN8 CPU Dual-core 32-bit Xtensa LX7 microcontroller with AI vector instructions up to 240MHz RISC-V ULP co-processor Memory – 512KB SRAM Storage – 8MB flash Wireless – 2.4GHz WiFi 4 (802.11b/g/n), Bluetooth 5.0 LE + Mesh Connectivity 2.4 GHz WiFi 4, 20 MHz and 40 MHz bandwidth, IEEE 802.11 b/g/n protocol, up to 150 Mbps Bluetooth 5, […]

March 22, 2025

M5Stack StamPLC – An ESP32-S3-based PLC with opto-isolated inputs, relay ouputs, RS485, CAN Bus, and more

“M5Stamp PLC Controller with M5StampS3” or just “M5Stack StamPLC” is a programmable logic controller (PLC) based on the StampS3A ESP32-S3 wireless module and offering 8 opto-isolated digital inputs, 4 relay outputs supporting both AC and DC loads, plus RS485 and CAN Bus interfaces. The DIN Rail IoT controller also features a 1.14-inch color display, a RESET/BOOT button, 3 user buttons, and a buzzer or user interaction. The M5Stack StamPLC also integrates an LM75 temperature sensor and an INA226 voltage/current sensor, as well as a microSD card slot for data storage, and it can take a wide voltage input between 6 and 36V DC. M5Stack StamPLC specfications: Control Module – StampS3A (similar to M5Stamp S3) SoC – Espressif Systems ESP32-S3FN8 CPU – Dual-core 32-bit Xtensa LX7 microcontroller with AI vector instructions up to 240MHz, RISC-V ULP co-processor Memory – 512KB SRAM Storage- 8MB flash Wireless – 2.4GHz WiFi 4 (802.11b/g/n), Bluetooth […]

August 20, 2024September 2, 2024

XIAO RA4M1 stamp-sized Renesas RA4M1 USB-C board features 14-bit ADC, 12-bit DAC, CAN Bus interfaces

Seeed Studio has added yet another member to their XIAO board family with the XIAO RA4M1 powered by Renesas’ RA4M1 32-bit Arm Cortex-M4 MCU. This compact board includes 256KB Flash, 32KB SRAM, a 14-bit A/D converter, a 12-bit D/A converter, a CAN bus interface, and onboard charging circuitry. It’s designed for low-power, battery-powered applications. The company started the XIAO family with the Seeeduino XIAO (Microchip SAMD21G18) in 2020, and since then they’ve made several other variants with different processors including the XIAO RP2350, XIAO RP2040, XIAO ESP32C3, XIAO ESP32S3, XIAO ESP32C6, and the nRF52840-based XIAO BLE. Feel free to check them out if you are interested in these boards. XIAO RA4M1 specifications: Microcontroller – Renesas RA4M1 (R7FA4M1AB3CFM) as found in Arduino UNO R4 CPU – Arm Cortex-M4F operating at up to 48 MHz Memory – 32KB SRAM Storage 256 KB code flash memory 8 KB data flash memory USB – 1x […]

August 10, 2024August 19, 2024

Solder Party’s “RP2350 Stamp” modules features Raspberry Pi RP2350A or RP2350B microcontroller

Solder Party’s RP2350 Stamp is an update to the company’s tiny RP2040 Stamp module based on a Raspberry Pi RP2350A, and they also introduced the RP2350 Stamp XL module that makes use of the extra GPIO pins on the RP2350B, and a “RP2xxx Stamp Carrier XL” carrier board taking either module. RP2350 Stamp and RP2350 Stamp XL The RP2350 Stamp has exactly the same layout as the RP2040 Stamp and mostly benefits from the more powerful Cortex-M33 cores, additional memory, and security features, while the XL variant adds more GPIOs, footprint for a PSRAM chip, as well as UART and SWD connectors. Both come with a 16MB SPI flash for storage. RP2350 Stamp specifications: Microcontroller – Raspberry Pi RP2350A MCU CPU – Dual-core Arm Cortex-M33 processor @ 150MHz Memory – 520KB internal RAM 8KB OTP Storage Package – QFN-60; 7×7 mm Storage – 16MB flash I/Os – All 30x I/Os […]

August 2, 2024May 1, 2026

M5Stamp Fly ESP32-S3 WiFi drone is controlled by the M5Atom WiFi joystick controller using ESPNOW

M5Stack M5Stamp Fly is a tiny ESP32-S3 WiFi drone based on the company’s M5Stamp S3 WiFi 4 and BLE IoT module, equipped with four motors and several sensors. and controllable, the M5Atom WiFi joystick controller is also based on ESP32-S3 WiSoC. We have recently seen some tiny ESP32 or ESP8266 WiFi drones with a low-cost ESP32 DIY drone and the PiWings 2.0 drone, but the M5Stamp Fly is more advanced with a total of six sensors, including a barometer, two time-of-flight distance sensors, a 6-axis IMU, a 3-axis magnetometer, and an optical flow detection sensor, plus two Grove connectors for additional sensors or modules. M5Stamp Fly (K138) specifications: Main controller – M5Stamp S3 module WiSoC – Espressif Systems ESP32-S3FN8 dual-core 32-bit Xtensa LX7 microcontroller with AI vector instructions up to 240MHz, RISC-V ULP co-processor, 512KB SRAM, 2.4GHz WiFi 4 (802.11b/g/n), Bluetooth 5.0 BLE + Mesh, 8MB flash Connectivity 2.4 GHz […]