You searched for RP2350B - Page 2 of 5 - CNX Software

October 3, 2024October 3, 2024

Jumperless V5 programmable breadboard is based on Raspberry Pi RP2350B, features a built-in power supply (Crowdfunding)

Jumperless V5 is a one-of-a-kind, programmable breadboard based on a Raspberry Pi RP2350B microcontroller that lets you skip the jumper wires and jump right into prototyping. It is described as “an Integrated Development Environment (IDE) for hardware.” The Jumperless V5 also removes the need for test equipment as it comes with built-in power supplies and can function as a multimeter, oscilloscope, function generator, and logic analyzer. As the name implies, the Jumperless V5 breadboard is a revamped version of the original Jumperless, with significant upgrades to make the board easier to use. The Jumperless V5 features a 14 x 30 LED matrix display under the breadboard, a probe for making connections and measurements, four ±8 V, 300 mA power supplies, daisy-chain headers, and overcurrent/overvoltage protection. The software-defined jumpers allow all points to be connected. The four individually programmable ±8 V power supplies, GPIOs, and management channels for voltage, current, and […]

August 16, 2024August 19, 2024

Bus Pirate 5XL and 6 hardware debugging tools utilize Raspberry Pi RP2350A and RP2350B microcontrollers

The Bus Pirate 5XL and 6 are open-source hardware debugging tools respectively based on Raspberry Pi RP2350A and RP2350B and designed to simplify interaction with various bus protocols like 1-Wire, I2C, SPI, UART, several LEDs, and more. The idea is to send commands to a chip or sensor and get the response, without writing a single line of code making it ideal for hardware hacking and tinkering. The devices feature buffered I/O pins with voltage and current measurement, a programmable power supply with current limiting, an RGB LCD for pin status and info, and an auxiliary header for connecting logic analyzers. All these features make this device useful for applications like debugging circuits, prototyping projects, and reverse engineering devices. The new devices are updates to the Bus Pirate 5 based on Raspberry Pi RP2040 MCU. You’ll find Bus Pirate specifications for the three models in the table below. The original […]

Solder Party’s “RP2350 Stamp” modules features Raspberry Pi RP2350A or RP2350B microcontroller

Solder Party’s RP2350 Stamp is an update to the company’s tiny RP2040 Stamp module based on a Raspberry Pi RP2350A, and they also introduced the RP2350 Stamp XL module that makes use of the extra GPIO pins on the RP2350B, and a “RP2xxx Stamp Carrier XL” carrier board taking either module. RP2350 Stamp and RP2350 Stamp XL The RP2350 Stamp has exactly the same layout as the RP2040 Stamp and mostly benefits from the more powerful Cortex-M33 cores, additional memory, and security features, while the XL variant adds more GPIOs, footprint for a PSRAM chip, as well as UART and SWD connectors. Both come with a 16MB SPI flash for storage. RP2350 Stamp specifications: Microcontroller – Raspberry Pi RP2350A MCU CPU – Dual-core Arm Cortex-M33 processor @ 150MHz Memory – 520KB internal RAM 8KB OTP Storage Package – QFN-60; 7×7 mm Storage – 16MB flash I/Os – All 30x I/Os […]

July 11, 2026

Lua-programmable ELM11-Feather board puts Gowin GW1NR FPGA into Feather form factor (Crowdfunding)

BrisbaneSilicon ELM11-Feather is a “microcontroller” board based on a Gowin GW1NR FPGA that is natively programmable in Lua, C, SystemVerilog, and VHDL. Compatible with the Adafruit Feather form factor, the board features GPIO headers, a built-in debugger, a USB-C port for power and programming, and a 2-pin header for a LiPo battery. The company calls it a microcontroller board because the FPGA runs a PicoRV32 MCU softcore at up to 75 MHz with 1MB RAM and 8MB flash, programmable with Lua, and the user can also customize hardware layers with RTL code using the remaining FPGA fabric. ELM11-Feather specifications: FPGA – Gowin GW1NR-LV9 FPGA from the GW1NR-9 family 8K LUTs 8,640 logical units (LUTs) 6,480 flip-flop 17,280 bits shadow SRAM (SSRAM) 486 Kbit block SRAM (BSRAM) 64 Mbit (8MB) PSRAM 608 Kbit user flash 2x PLL Up to 276x user I/O USB – 1x USB Type-C port for power and […]

March 18, 2026March 18, 2026

PycoClaw – A MicroPython-based OpenClaw implementation for ESP32 and other microcontrollers

PycoClaw is a MicroPython-based platform for running AI agents on ESP32 and other microcontrollers that brings OpenClaw workspace-compatible intelligence to resource-constrained embedded devices. We had already covered the C-based Miniclaw for ESP32-S3 SoCs, the PycoClaw’s developer (Jonathan Peace) told CNX Software that it is a “full OpenClaw-compliant agent” that supports more LLM providers (OpenAI, Gemini, Ollama, etc.), interfaces with not only Telegram, but also ScriptO Studio and WebRTC, and offers features like OTA updates, extensions, and battery-optimized operation. The table below compares PycoClaw to OpenClaw, Nanobot, PicoClaw, NullClaw, and MimiClaw. MimiClaw still offers the lowest footprint and highest efficiency, but PycoClaw appears to offer many more features, including improved GPIO support. It works on ESP32-S3 with at least 8MB flash and PSRAM, ESP32-P4, and should soon support Raspberry Pi RP2350 boards with PSRAM as well. PycoClaw can be installed on supported hardware through a “one-click install” using a compatible web […]

October 19, 2025October 18, 2025

RP2350 Tiny and Tiny XL boards clone Solder Party’s RP2350 stamp layouts at nearly half the price

While searching Aliexpress, I stumbled upon the RP2350 Tiny and Tiny XL, both of which are RP2350-based low-cost stamp-size development boards that look exactly like the Solder Party’s “RP2350 Stamp” modules, but are available at nearly half the price. Both modules feature the Raspberry Pi RP2350 dual-core Arm Cortex-M33 microcontroller and an integrated LiPo charging circuitry. The RP2350 Tiny offers 30x GPIOs, while the larger RP2350 Tiny XL breaks out 48x GPIOs, adds PSRAM, and includes SWD/UART JST connectors. Key interfaces include USB host/device, UART, SPI, I²C, PWM, ADC, and PIO state machines, along with Secure Boot and Arm TrustZone. These features make this board suitable for rapid prototyping and testing with CircuitPython support. RP2350 Tiny and Tiny XL specifications: Microcontroller RP2350 Tiny – Raspberry Pi RP2350A MCU, QFN-60; 7×7 mm RP2350 Tiny XL – Raspberry Pi RP2350B MCU,QFN-80; 10×10 mm Memory – 520KB internal RAM, 8KB OTP storage Storage – 16MB […]

Olimex RP2350 PICO2 BB48 Open Source Development Board

September 29, 2025November 2, 2025

Olimex RP2350-PICO2 open hardware boards expose all 48 GPIOs for breadboard prototyping

Olimex RP2350-PICO2-BB48 and RP2350-PICO2-BB48R open hardware development boards are built around the Raspberry Pi RP2350B MCU, and expose all 48 GPIOs in a 0.6-inch dual-inline PCB layout. Compared to the earlier PICO2-XL and PICO2-XXL boards, this new board features a breadboard-friendly design with options for PSRAM and microSD on the BB48R version. Other features include USB-C power/data, BOOT and RESET buttons, a 2A 3.3V regulator, UEXT and Qwiic/Stemma connectors, status LED, and debug pads. With pre-soldered headers, it can be plugged directly into a breadboard, making it ideal for DIY projects, IoT, retro computing, and hardware prototyping. Olimex RP2350-PICO2-BB48 and RP2350-PICO2-BB48R specifications: MCU – Raspberry Pi RP2350B CPU Dual-core Arm Cortex-M33 @ 150 MHz with Arm Trustzone, Secure boot OR Dual-core RISC-V Hazard3 @ 150 MHz Either two cores can be used. Memory – 520 KB on-chip SRAM Package – QFN-80 Memory – 8 MB external QSPI PSRAM (only on […]

August 27, 2025August 30, 2025

Adafruit Fruit Jam – An RP2350 mini computer running classic Macintosh

The Adafruit Fruit Jam is a credit card-sized RP2350-powered mini computer that is designed to run classic Macintosh through the uMac emulator. It supports System 2.0 up to System 7.5.5, 720p video via DVI, audio, and USB keyboard and mouse. Built around the Raspberry Pi RP2350 MCU, the Fruit Jam board also features an ESP32-C6 wireless module and offers DVI output via the RP2350’s HSTX interface, USB-C for bootloading, a microSD card slot for storage, and an onboard TLV320DAC3100 I2S audio DAC for stereo headphones and a mono speaker. There’s also a 16-pin GPIO header, NeoPixels LEDs, tactile switches, and STEMMA QT and JST connectors for expansion. These features make this board suitable for retro emulation, educational projects, and lightweight standalone computing. Adafruit Fruit Jam specifications: Microcontroller – Raspberry Pi RP2350B CPU Dual-core Arm Cortex-M33 @ 150 MHz with Arm Trustzone, Secure boot OR Dual-core RISC-V Hazard3 @ 150 MHz […]