You searched for ESP32-S3 - Page 30 of 47 - CNX Software

Renesas RA2T1 microcontroller (MCU) group

July 14, 2025July 13, 2025

Renesas RA2T1 low-power Cortex-M23 MCUs target BLDC/PMSM motor applications

Renesas has recently launched the RA2T1 group of low-power motor control MCUs, built around a 64 MHz Arm Cortex-M23, for low-cost single-motor applications like power tools, fans, and home appliances. Designed for Brushless DC Electric Motors (BLDC) and Permanent Magnet Synchronous Motors (PMSM), the RA2T1 supports both trapezoidal and FOC control techniques, thanks to its integrated 3-channel Sample and Hold (S&H) circuits that enable accurate 3-phase current detection. It also includes PWM shutdown features and various analog and digital peripherals in compact packages as small as 4×4 mm QFN. Previously, Renesas introduced the RA8T1, also a motor control MCU based on the Cortex-M85 core with Helium instructions and DSP extensions. Ideal for AI-enhanced motor control in industrial and robotics applications. Around the same time, Infineon launched the PSOC Control C3x series, with real-time motor control and security features along with fast ADCs, high-resolution PWM, and PSA Level 2 compliance. Renesas […]

July 11, 2025

M5Stack Stamp-S3A WiFi and BLE IoT module benefits from optimized antenna design, lower power consumption

M5Stack Stamp-S3A, also known as M5StampS3A, is an update to the M5Stamp S3 ESP32-S3 module introduced in 2023 with an optimized antenna design, lower power consumption, a larger user button, and a different logic for the RGB LED control. Other features remain the same with 8MB Flash, RGB LED, input button, and 23 GPIOs all in a tiny 26 x 18mm form factor. Two versions are available: the Stamp-S3A without pre-soldered headers and the Stamp-S3A PIN1.27 with headers soldered on the board and an orange heat-resistant cover. M5Stamp-S3A specifications: WiSoC – Espressif Systems ESP32-S3FN8 CPU Dual-core 32-bit Xtensa LX7 microcontroller with AI vector instructions up to 240MHz RISC-V ULP co-processor Memory – 512KB SRAM Storage – 8MB flash Wireless – 2.4GHz WiFi 4 (802.11b/g/n), Bluetooth 5.0 LE + Mesh Connectivity 2.4 GHz WiFi 4, 20 MHz and 40 MHz bandwidth, IEEE 802.11 b/g/n protocol, up to 150 Mbps Bluetooth 5, […]

July 11, 2025

Industrial 6-Channel RP2350 relay module offers RS485 interface, Raspberry Pi Pico HAT support

Waveshare RP2350-Relay-6CH is a Raspberry Pi RP2350-based industrial 6-channel relay module with an isolated RS485 interface, 7 to 36V DC input via a terminal block, and support for Raspberry Pi Pico HATs. Each relay is isolated and can handle 250VAC/30VDC up to 10A, a USB-C port is used for firmware updates, and the module also includes a buzzer, a few LEDs, as well as Reset and BOOT buttons, with everything housed in a DIN-Rail enclosure. Waveshare RP2350-Relay-6CH specifications: Microcontroller – Raspberry Pi RP2350B CPU Dual-core Arm Cortex-M33 @ 150 MHz with Arm Trustzone, Secure boot OR Dual-core RISC-V Hazard3 @ 150 MHz Either two cores can be used. Memory – 520 KB on-chip SRAM Package – QFN-80 Relay – 6x relays Contact rating – ≤10A 250VAC/30VDC Contact form – 1NO 1NC via screw terminals Optocoupler isolation USB – USB Type-C port for power, data, and firmware flashing Serial Isolated RS485 […]

July 7, 2025

ThinkNode M1/M2 Review – Getting started with Meshtastic

I’ve been writing about Meshtastic firmware and hardware since 2020, but I never had the opportunity to test it myself. This has now changed as Elecrow sent us the ThinkNode M1 and ThinkNode M2 Meshtastic nodes for review. Both rely on Semtech SX162x radios, but the M1 is based on a Nordic Semi nRF52840 Bluetooth MCU with a 1.54-inch E-Ink display and GPS, and the smaller M2 is based on an ESP32-S3 chip and a 1.3-inch OLED but lacks a built-in GPS module. Since I’ve never used Meshtastic before, this “review” will be more like a Getting Started Guide from a beginner’s perspective. After an unboxing and a teardown, I’ll test messaging, GPS sharing, and the range I can get in a suburban environment in Thailand. ThinkNode M1/M2 unboxing Both packages look similar, with a plastic case and a white cover. The ThinkNode M1’s main features include a high-gain antenna, […]

July 3, 2025July 4, 2025

WisMesh Board ONE allows you to build a custom Meshtastic Node with OLED, GPS, battery, enclosure, and more

There are now plenty of Meshtastic hardware platforms for off-grid messaging, audio communication, and GPS coordinate sharing, be it boards or modules for DIY projects, or complete solutions with battery and enclosure working out of the box, such as the Wio Tracker L1 Pro or ThinkNode M2, among many others. In some ways, RAKwireless’ WisMesh Board ONE baseboard offers the best of both worlds, combining the flexibility of DIY designs with the convenience of complete solutions, as it allows users to create a custom Meshtastic node with optional OLED, GPS, battery, antennas, and enclosure besides the usual choice between 868 MHz and 915 MHz LoRa radios. WisMesh Board ONE specifications: Wisblock RAK4631 Module pre-flashed with the Meshtastic firmware SoC – Nordic Semi nRF52840 Core – 32-bit Arm Cortex-M4F CPU @ 64 MHz Memory – 256 KB SRAM Storage – 1 MB Flash Wireless – Bluetooth LE LoRa Transceiver – Semtech […]

June 19, 2025

HackLED Pro LED controller – An Adafruit Sparkle Motion alternative with WS2812 and RGBCW LED support

HACK Lab HackLED Pro is an Adafruit Sparkle Motion-like LED controller that runs a custom version of WLED and supports both WS2812 and RGBCW LEDs, making it ideal for DIY lighting projects, smart home setups, and audio-reactive light displays. Built around an ESP32 MCU, this board includes 2-way WS2812 LED outputs, 5 PWM channels (RGBCW), and an onboard silicon microphone for music reactive LED setup. Like the Sparkle Motion, the outputs of this board are level-shifted, and there’s also a power switch that toggles the output power between 5V and 12V. The board features a USB-C port with a PD controller, with which you can power and program the board. The controller is housed in a thermally protected 3D printed case and is also compatible with the generic version of the WLED firmware. HackLED Pro specifications: Wireless module – ESP32-WROOM-32E-N4 WiFi and Bluetooth module with 4MB Flash LED Control 2x […]

June 14, 2025

Valtrack V4 is a programmable 4G LTE GPS vehicle tracker with ESP32-C3 Bluetooth & Wi-Fi SoC (Crowdfunding)

Valetron Systems VALTRACK-V4-VTS-ESP32-C3 (or Valtrack V4 for short) is a 4G LTE GPS vehicle tracker based on ESP32-C3 WiFi and Bluetooth SoC and a SIMCom SIM7672 cellular and GNSS module. Designed to track bicycles, cars, or trucks, the Valtrack V4 GPS tracker is housed in an IP67 waterproof enclosure, takes 12V to 42V DC input from a lead battery or 3.7-4.2V from a backup LiPo or Li-Ion battery, and features an accelerometer to wake up when motion is detected or detect theft, as well as three RGB LEDs for status. Valtrack V4 specifications: Wireless MCU – Espressif ESP32-C3FH4 CPU – 32-bit RISC-V microcontroller @ up to 160 MHz; Memory – 400 KB SRAM Storage – 4 MB flash Wireless – 2.4 GHz Wi-Fi 4 & Bluetooth 5.0 Cellular and GNSS connectivity SIM7672G 4G LTE Cat 1 module with Global LTE band, 2G fallback, and GNSS support Nano SIM card […]

RAK11160 ESP32-C2 STM32WL LoRaWAN module

June 9, 2025June 16, 2025

$6.5 RAK11160 LoRaWAN, WiFi, and BLE module pairs ESP32-C2 with STM32WLE5 for low-power, long-range IoT

RAKwireless RAK11160 is a new low-cost, low-power LoRaWAN, WiFi 4, and Bluetooth LE module based on ESP32-C2 (ESP8684) wireless microcontroller and STM32WLE5 LoRa SoC for LPWAN IoT applications. The company noticed that many people would combine their STMicro STM32WL-based RAK3172 WisDuo LoRaWAN module with an ESP32 module to add WiFi and/or Bluetooth connectivity to their projects besides LoRaWAN. So RAKwireless decided to offer a module combining both STM32WL and ESP32-C2 to offer a cheap and much more compact solution to their customers. RAK1160 was born. RAwireless RAK11160 specifications: LPWAN SoC/SiP – STMicro STM32WLE5 Core – Arm Cortex-M4 MCU @ 48 MHz Memory – 64 KB RAM Storage – 256 KB flash memory with ECC Wireless – Sub-GHz radio based on Semtech SX126x LoRaWAN 1.0.4 specification compliant Supported bands – EU433, CN470, IN865, EU868, AU915, US915, KR920, RU864, and AS923 LoRaWAN Activation by OTAA/ABP LoRa Point-to-Point (P2P) communication Tx Power Output – […]