Posted on

Android and Linux Benchmarks on MiQi Development Board

MiQi is an upcoming low cost development board powered by Rockchip RK3288 SoC that will sell for $35 with 1GB RAM and 8GB storage, and $69 for the version with a  2GB / 32GB combination. Since Rockchip RK3288 was launched in 2014, most available benchmarks were made on Android 4.4, and since MiQi is the first low cost board based on the processor, other RK3288 based board such as FireFly have not been that popular. So I’ve decided to run updated benchmarks in MiQi both in Android 5.1 and Linux (Lubuntu 14.04), which was easy since a dual boot image is pre-installed. But since I received an early sample without heatsink, I found a spare heatsink added some thermal paste and placed it on top of the processor and partially on RAM and eMMC flash. MiQi Board Android 5.1 Benchmarks I ran Antutu both using 1080p60 and 2160p30 video output, […]

Posted on

SmartEverything is a Feature-Packed IoT Board with SigFox, Bluetooth LE, NFC and GPS Connectivity, Plenty of Sensors

Atmel MCU Madness is an informal competition on Twitter where people vote for their favorite development boards. We are now at the quarter finals, and beside the usual suspects such as Raspberry Pi and ESP8266 boards, I also noticed one board that I had never heard of: AXEL Elettronica’s SmartEverything based on Atmel SAM D21 Cortex M0+ and featuring SigFox, BLE, NFC, and GPS connectivity, as well as various sensors such as humidity and temperature, 9-axis motion sensor, and so on. SmartEverything board specifications: MCU – Atmel SAM D21 ARM Cortex-M0+ MCU @ 48 MHz with 256KB Flash, 32KB SRAM Connectivity SIGFOX via Telit LE51-868 S SIGFOX 868 MHz Wireless Module with 12 months of network access included Bluetooth 4.0 LE via  TDK SESUB-PAN-T2541 module based on Texas Instruments CC2541 NFC via NXP NT3H1101FHK NFC with separate antenna (included) GPS/GNSS via Telit Jupiter SE868-A GPS/GNSS module with integrated antenna. Supports […]

Advertisement
Posted on

Linux 4.5 Released – Main Changes, ARM and MIPS Architectures

Linus Torvalds released Linux Kernel 4.5 on Sunday: So this is later on a Sunday than my usual schedule, because I just couldn’t make up my mind whether I should do another rc8 or not, and kept just waffling about it. In the end, I obviously decided not to,but it could have gone either way. We did have one nasty regression that got fixed yesterday, and the networking pull early in the week was larger than I would have wished for. But the block  layer should be all good now, and David went through all his networking commits an extra time just to make me feel comfy about it, so in the end I didn’t see any point to making the release cycle any longer than usual. And on the whole, everything here is pretty small. The diffstat looks a bit larger for an xfs fix, because that fix has […]

Posted on

ODROID-C2 Amlogic S905 Development Board is in the Works

Hardkernel ODROID-C1 and later ODROID-C1+ boards, both based on Amlogic S805 SoC, have been a popular alternatives to Raspberry Pi 2 board this year. But now that Amlogic S905 quad core 64-bit ARM Cortex A53 processor has been available for a few months, people have been wondering whether the Korean company would launch an Amlogic S905 board, and it looks like ODROID-C2 might not be too far off based on firmware files on odroid.in website. The firmware includes a device tree file, which combined with other files give some clues about ODROID-C2 specifications: SoC – Amlogic S905 quad core Cortex A53 processor @ up to 2.0 GHz with penta-core (3+2) Mali-450MP GPU System Memory – 1GB RAM (in doc), 2GB RAM (in Device tree) Storage – 1x micro SD card Video Output – 1x HDMI out USB – 1x USB hub, 1x USB OTG I don’t have much more information […]

Posted on

Hardkernel ODROID-XU4 Development Board Now Supports Android 6.0 Marshmallow

Android 6.0 source code was released in October, but so far few development boards are supporting it properly. There’s Android 6.0 for Raspberry Pi 2, but without GPU hardware acceleration is not really usable, and Intrinsyc Open-Q 820 board that will start shipping in a few days with Android 6.0 on Qualcomm Snapdragon 820 processor, is pricey and with limited availability. So there are only two options that I’m aware of LeMaker Hikey with Android 6.0 as part of the Reference Platform Release 2015.12, and Hardkernel ODROID-XU4 with an unofficial port for Android 6.0.1 Marshmallow by voodik odroid community member, which should also work for ODROID-XU3 and XU3 Lite boards. Despite being an alpha version, the current image looks pretty good, as most required features seem implemented: Android 6.0.1 Lollipop Cyanogenmod 13.0 with Linux kernel 3.10.9 OpenGL ES 1.1/2.0/3.0 (GPU acceleration) OpenCL 1.1 EP (GPU acceleration) Multi-user feature is enabled […]

Posted on

HummingBoard Edge SBC Gets an mSATA/M.2 Connector, an eMMC Flash, and More I/Os

SolidRun launched its HummingBoard family last year with a board with a form factor similar to the Raspberry Pi, but instead of using a Broadcom processor, the boards were based on Freescale i.MX6 single, dual or quad core processors. The company has recently introduce a higher end board with Hummingboard Edge that adds an M.2 connector, eMMC flash, 7 to 36V DC power input, more camera interfaces, a DSI interface, and more GPIOs. The following comparison table shows the differences between the new Hummingboard Edge, and the older HummingBoard Pro and Base boards. HummingBoard-Edge HummingBoard-Pro HummingBoard-Base uSOM model i.MX6 based Solo to Quad Core uSOM Memory Up to 4GB DDR3 Storage uSD, eMMC, M.2/mSATA uSD, mSATA uSD Connectivity 1x RJ45*, 4x USB 2.0, mPCIE with SIM card holder 1x RJ-45*, 2x USB 2.0 Hosts, 2x USB 2.0 header, mPCIE half-size 1x RJ-45*, 2x USB 2.0 Hosts Media HDMI-out, LVDS, analog […]

Rockchip RK3568, RK3588 and Intel x86 SBCs and SoMs in 2025
Posted on

$10 Digistump Oak ESP8266EX Board is Arduino Compatible, Connects to the Cloud, and More (Crowdfunding)

A few years ago, I wondered why adding Wi-Fi to Arduino had to be rather expensive ($40+), and why there weren’t any low cost and small form factor Wi-Fi boards for embedded applications. But we’re now in 2015, embedded is “dead” giving rise to IoT, and I’m left wondering how it’s possible to make IoT Wi-Fi modules that cheap, and whether people will ever stop churning out cheap Wi-Fi boards, as I’m flooded with such news weekly… So when I saw yet another ESP8266 board on Kickstarter I was about to dismiss it, but since it was made by Digistump, that has an active community with their other products like DigiSpark Pro or DigiX, I decided to have a closer look. Digistump Oak hardware specifications: MCU – Espressif ESP8266EX 32-bit microprocessor @ 80MHz (overclockable up to 160MHz)  with 1MB ROM (~300KB available for user code), 64KB RAM, 512 bytes EEPROM […]

Posted on

Snappy Ubuntu Core is an IoT Linux Distribution for ARM and x86

Canonical has announced a version of Ubuntu specifically designed for IoT devices running Linux, with a low hardware requirements, and a new package manager called snappy, replacing apt-get for this version of Ubuntu, which provides simpler, faster, and more reliable updates, stronger security, and allows roll-backs in case something goes wrong. Easy firmware updates are something missing in most connected device, which means they are more vulnerable to potential hackers, but with snappy security updates should be able to make it regularly, so that if something like heartbleed occurs again, you know your router, home automation gateway, connected washing machine, or robot will be soon patched automatically. Let’s go through the hardware requirements first: Processor – 600 MHz processor (ARMv7 or greater, or x86) System Memory – 128 MB RAM or greater (The system itself uses 40 MB RAM) Storage – 4GB flash / storage for factory reset and system […]

Boardcon MINI1126B-P AI vision system-on-module wit Rockchip RV1126B-P SoC