development board

Posted on by Jean-Luc Aufranc (CNXSoft) - 5 Comments on PocketBone Board Based on Octavo Systems OSD3358 SiP Fits into an “Altoids Smalls” Mint Tin Box

PocketBone Board Based on Octavo Systems OSD3358 SiP Fits into an “Altoids Smalls” Mint Tin Box

Last year, Octavo Systems introduced OSD3358 System-in-Package (SiP) that includes Texas Instruments Sitara AM3358 processor, 256MB to 1GB RAM, a PMIC and an LDO into a single package. Since then the SiP has been found in BeagleBone Black Wireless and BeagleBone Blue, and at the time of launch there was also some development around PocketBone, a tiny open source hardware Smalls mint tin sized board based on OSD3358, which is smaller than a CHIP board, but a little bigger than NanoPi NEO board. There’s now been some progress with prototypes of the board manufactured with the following specifications: SiP (System-in-Package) – Octavo Systems OSD3358 with TI Sitara AM3358 ARM Cortex-A8 processor @ up to 1 GHz,  PowerVR SGX530 GPU, PMIC + LDO, and 512MB DDR3 Storage – micro SD slot USB – 2x micro USB port one for power, one OTG port Expansion – 10-pin header (unpopulated) with SPI, I2C, […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 5 Comments on Mirabook is Laptop Dock for Smartphones, Development Boards (Crowdfunding)

Mirabook is Laptop Dock for Smartphones, Development Boards (Crowdfunding)

Motorola Lapdock may have been ahead of its time, as laptop docks for smartphone are back in vogue with products like NexDock, and Apple could soon launch their own iPhone laptop dock. Another option is Miraxess Mirabook laptop dock with a 13.3″ display, and a battery lasting up to 24 hours, that works for smartphones, development boards, and HDMI TV sticks thanks to its USB type C port. Mirabook specifications: Display – 13.3″ IPS display with 1920×1080 resolution (non-touch, except if they raise $2 millions…) Audio – Speakers, 3.5mm audio jack Video Output – HDMI port Storage – SD card slot QWERTY keyboard & multi-touch trackpad USB Integrated USB type C cable to connect to phone, board or HDMI TV stick USB type C port to charge the Mirabook battery 2x USB type A host port Battery – TBD capacity good for 24 hours while charging your phone Dimensions – […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 7 Comments on MAXOAK K2 Laptop Power Bank Review – Part 2: Tests with Laptops, Phones and Development Boards

MAXOAK K2 Laptop Power Bank Review – Part 2: Tests with Laptops, Phones and Development Boards

MAXOAK K2 is a large capacity (50,000 mAh) power bank designed for laptop with ~20V and 12V outputs, but it can also charge USB devices thanks to its 4 USB ports. Since I’ve already checkout the device and specifications in the first part of the review, I’ll report results from my tests with the power bank in the last couple of weeks. Since the power bank had some charge, more exactly between 50 and 75% (2x LEDs on, 1x LED blinking, 1x LED off), I decided to start by charging my phone, Vernee Apollo Lite, which is equipped with a 3,180 mAh battery. So I connected the phone to one of the two 5V/2.1A USB port, together with USB Charger Doctor to monitor voltage and current, and with 50% charge, the phone would draw around 5.07V @ 1.15 A. Note that the voltage and amperage will change depending on battery […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on Particle Asset Tracker Kit v2 2G/3G GPS Location Tracker Supports Grove Modules

Particle Asset Tracker Kit v2 2G/3G GPS Location Tracker Supports Grove Modules

Particle, the maker of IoT boards such as Electron 2G/3G module, has launched it second Asset Tracker Kit – based on Electron – with a smaller case, improved GPS performance, satellite support for GPS, GLONASS, Galileo & BeiDou, and compatibility with Seeed Studio Grove modules. Asset Tracker Kit v2 hardware specifications: MCU – STMciro STM32F205 ARM Cortex M3 micro-controller @ @ 120 MHz with  1MB Flash, 128K RAM Cellular Connectivity – U-Blox SARA U-series (3G) or G-series (2G) modem + NanoSIM card slot + u.FL connector for Antenna Location 72-channel u-bloxM8 engine with support for GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1I, Galileo E1B/C, SBAS L1 C/A: WAAS, EGNOS, MSAS, GAGAN Update rates: Single GNSS: up to 18 Hz, 2 Concurrent GNSS: up to 10 Hz Position accuracy of 2.5 m, sensitivity of -167 dBm Acquisition times: Cold starts: 26s, Aided starts: 2s, Reacquisition: 1s On board ceramic GPS antenna […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 40 Comments on $40 NanoPi K2 Board Powered by Amlogic S905 Processor Competes with ODROID-C2, Raspberry Pi 3

$40 NanoPi K2 Board Powered by Amlogic S905 Processor Competes with ODROID-C2, Raspberry Pi 3

Hardkernel ODROID-C2 board is getting some direct competition with FriendlyELEC’s NanoPi K2 development board powered with Amlogic S905 processor with 2GB RAM, a very similar form factor, and many of the same features, which together with Khadas Vim (Pro) brings the number of low cost Amlogic based development boards to three. NanoPi K2 board specifications with differences compared to ODROID-C2 highlighted in bold or stricken-through: SoC – Amlogic S905 quad core cortex-A53 processor @ 1.5 GHz with penta core Mali-450MP GPU System Memory – 2GB DDR3 Storage – eMMC module socket, micro SD slot Video Output – HDMI 2.0 up to 4K @ 60 Hz Connectivity – Gigabit Ethernet (Realtek RTL8211F), 802.11 b/g/n WiFi + Bluetooth 4.0 (AP6212 module) with chip antenna + IPX connector USB – 4x USB 2.0 host ports (GL825G USB hub) + micro USB OTG port for power and adata Expansion Header 40-pin header with GPIO, […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 8 Comments on MYIR MYS-6ULX is a $25 Single Board Computer based on NXP i.MX 6ULL/6UL Processor for IoT and Industry 4.0

MYIR MYS-6ULX is a $25 Single Board Computer based on NXP i.MX 6ULL/6UL Processor for IoT and Industry 4.0

MYIR Tech has released MYS-6ULX single board computer based on  NXP i.MX 6ULL/6UL Cortex-A7 processor designed for either Industry 4.0 with MYS-6ULX-IND model, or the Internet of Things for MYS-6ULX-IOT. Both boards include 256MB DDR3 SDRAM, 256MB NAND flash, USB, USB, Ethernet, LCD interfaces and more, in a compact 70 x 55mm form factor. Both boards have very similar specifications. Features MYS-6ULX-IND MYS-6ULX-IOT SoC NXP i.MX 6UltraLite (MCIMX6G2CVM05AA) with an ARM Cortex A7 processor @ up to 696 MHz and 2D graphics accelerator NXP i.MX 6ULL (MCIMX6Y2DVM05AA) with an ARM Cortex A7 processor @ 528 MHz and 2D graphics accelerator DDR3 256MB (support up to 2GB) NAND Flash 256MB (support 512MB/1GB) eMMC DNP (Do Not Populate – Reserved design for optional 4GB flash) Ethernet 10/100Mbps USB 1x USB Host, 1x micro USB OTG Micro SD Card 1x Micro SD card slot Buttons 1x Reset Button, 1x User Button LED 1x Power Indicator, 2x […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 1 Comment on No Case for Orange Pi Zero or Other Tiny Development Boards? No problem: Use an Old Mouse

No Case for Orange Pi Zero or Other Tiny Development Boards? No problem: Use an Old Mouse

There now plenty of tiny ARM Linux boards, which are normally sold without case, but usually it’s not to hard to find a 3D printed case. But if you have small board, and don’t feel to purchase a case for it, there’s an other solution: use an old mouse. That’s exactly what Slider2732 has done with his Orange Pi Zero board to convert it to a mini PC running Armbian, or a game console running RetroOrangePi. So after the keyboard PC, here comes the mouse PC! So what did he exactly use for the mouse PC? Orange Pi Zero board An old Logitech mouse for the case and cable An 8GB micro SD card to flash the operating system A 4.3″ car reversing monitor (optional) acting as the display with composite input An Rii wireless keyboard/mouse, as the mouse function is not included with the mouse PC… A PAM8403 based […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 7 Comments on ESPurna-H is a Compact Open Source Hardware Board with ESP8266 WiSoC, a 10A Relay, HLW8012 Power Monitoring Chip

ESPurna-H is a Compact Open Source Hardware Board with ESP8266 WiSoC, a 10A Relay, HLW8012 Power Monitoring Chip

ESPurna is an open source firmware for ESP8266 based wireless switch as such Sonoff POW, which I’ve been personally using to monitor my office’s power consumption. The developer, Xose Pérez (aka tinkerman), has now developed his own hardware with ESPurna-H board, as existing wireless switches with power monitoring functions would not fit into a gang box. ESPurna-H board specifications: WiFi Module – ESP12 with Espressif ESP8266 WiSoC Relay – Songle SRD-05VDC-SL-C 10A relay with NO and NC connection Power Monitoring – HLW8012 chip as found in Sonoff POW Expansion – 2x 5-pin header with the programming GPIOs, and two connections for external button and LEDs Misc – Reset button Power Supply Input –  100 ~ 240V AC Output – 5V up to 600 mA via Hi-Link HLK-PM01 Safety – Optical isolation between the logic circuit and the relay circuit Dimensions – 50x50x20mm Xose designed the board with Eagle 8.0 and released […]