development board News - Page 171 of 258 - CNX Software

November 25, 2016 by Jean-Luc Aufranc (CNXSoft) - 14 Comments

Firefly-RK3399 Development Board Will Fly with Rockchip RK3399 Hexa-core Processor

ARM Cortex A72 class development boards are usually quite expensive, and cheaper boards like Mediatek X20 development board ($200) appears to be out of stock very often, and software support is limited to Android 6.0. But things look to improve soon, as T-Chip is about to release Firefly-RK3399 development board powered by Rockchip RK3399 hexa-core Cortex A72/A53 processor. Firefly-RK3399 (preliminary) specifications: SoC – Rockchip RK3399 hexa-core bit.LITTLE processor with dual core Cortex A72 up to 2.0 GHz and quad core Cortex A53 processor with ARM Mali-T860MP4 GPU with OpenGL 1.1 to 3.0 support, OpenVG 1.1, OpenCL and DX 11. System Memory – 2 to 4 GB DDR3 Storage – 16 to 32 GB eMMC flash + micro SD card Video Output & Display Interfaces – HDMI 2.0 up to 4K @ 60 Hz, eDP 1.2 interface, YUV interface, 1x MIPI DSI interface Video Decode – 4K VP9 and 10-bit H.265 […]

November 24, 2016 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

39 Euros FiPy Board Supports Sigfox, LoRa, LTE Cat M1/NB1, Bluetooth 4.2, and WiFi (Crowdfunding)

Long range LPWAN solutions have just started to hit the market, and there are so many standards such as Sigfox and LoRa that it’s difficult to know who will eventually be the winner, or if different standards will co-exist over the long term, and in a general sense it might not be so easy to decide which one is best suited to your project without experimenting first. Pycom has a solution to this problem, as they’ve made a board similar to LoPy with WiFi, Bluetooth, and LoRa, but instead included 5 long and short range IoT protocols: Sigfox, LoRa, LTE Cat M1 & Cat NB1, Bluetooth, and WiFi. Pycom FiPy board specifications: SoC – Espressif ESP32 dual core Tensilica L108 processors @ up to 160 MHz with BT 4.2 and WiFi System Memory – 4MB RAM Storage – 8MB flash memory Connectivity WiFi 802.11 b/g/n @ 16 Mbps up to […]

November 23, 2016 by Jean-Luc Aufranc (CNXSoft) - 11 Comments

OnChip Open-V Open Source 32-bit RISC-V Processor Launched on CrowdSupply

Open source hardware gives mostly full control over software and hardware, but there are different levels of openess, with some companies wrongly claiming their product to be open source hardware – with a nice accompanying logo – once they dump some source code somewhere and publish the PDF schematics, while others are doing it right with the release of schematics and PCB layout in source format, as well as software and proper documentation. However even for the latter group, the actual chips are closed source bought directly from silicon vendors or their distributors. So the good news is that you now have the opportunity to bring the meaning of open source hardware to a whole new level thanks to OnChip Open-V 32-bit processor that is open source, and getting launched on Crowd Supply crowdfunding platform. OnChip Open-V is based on RISC-V (pronounced “risk-five”), comes with peripherals, and should be competitive […]

November 22, 2016November 22, 2016 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

Badgerboard Arduino Compatible LoRa Board Goes for $43 and Up (Crowdfunding)

Here comes one more LoRa board to play with. Badgerboard combines an Arduino compatible Atmel/Microchip AVR MCU with a Microchip RN2483 or RN2903 module in a breadboard compatible board powered via micro USB port or an external battery. Badgerboard specifications: MCU – Atmel ATmega32U4 MCU Connectivity – LoRaWAN via Microchip RN2483 (EU – 868MHz) / RN2903 (US – 915 MHz) modem with SMA connector and antenna USB – 1x micro USB port for power and programming Expansion – 2x 18-pin unpopulated headers with SPI, I2C, 13x GPIOs, 6x 10-bit ADC, 3.3V and GND signals; open drain output for relays up to 24V 100 mA Sensors – STM HTS221 temperature and humidity sensor Misc – Reset button; user and Tx/Rx LEDs; power on/off switch Power Supply – 5V via micro USB port, or Li-Ion/ Li-Po battery via JST connector Dimensions – 56 x 26 mm The board can be programmed with […]

November 21, 2016November 22, 2016 by Jean-Luc Aufranc (CNXSoft) - 36 Comments

Raspberry Pi 2 Gets an Upgrade to 64-Bit Broadcom BCM2837 Processor with PCB Version 1.2

With the launch of Raspberry Pi 3 based on Broadcom BCM2837 quad core Cortex A53 processor earlier this year, sales of Raspberry Pi 2 boards have suffering meaning the demand for Broadcom BCM2836 quad core Cortex A7 processor has also been reduced, and it appears the Raspberry Pi foundation has now launched Raspberry Pi 2 V1.2 with the faster BCM2837 processor. The new Raspberry Pi 2 v1.2 runs BCM2837 CPU cores up to 900 MHz, instead of 1.2 GHz on RPi 3, and includes 1 GB RAM. The main difference with Raspberry Pi 3 is the lack of the WiFi and Bluetooth module, which may also prevent some UART issues if you want to access the serial console or use an add-on board with UART. Since both boards cost the same ($35), most people should probably stick with Raspberry Pi 3, unless you’d rather not have any wireless module on […]

November 20, 2016November 20, 2016 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

A Closer Look at Ingenu RPMA Alternative to LoRa or Sigfox LPWAN Standards & RPMA Development Kit

I’ve recently started to write a bit more about long range LPWAN standards for IoT applications, especially LoRa and Sigfox, as commercial networks are being launched, and relatively low cost hardware platforms are being introduced to the market. There are also other highly expected standards such as Weightless and LTE Cat M that will bring more competition to the market. Ingenu RPMA (Random Phase Multiple Access) is another available standard that’s been in deployment for a while, and based on an earlier comparison of long range LPWAN standards, it comes with long range, supports up to 384,000 nodes per “sector”, operates in the unlicensed 2.4 GHz ISM band, and offers high combined uplink and downlink bandwidth than competitors. Ingenu recently contacted me and provided some more details and information about their technology and development kit. One of the documents includes an “independent analysis completed by ABI Research, Inc.” comparing features […]

November 18, 2016June 18, 2018 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

$49 Dashbot Car Dashboard Assistant is Powered by C.H.I.P Pro Allwinner GR8 Module (Crowdfunding)

Most companies specializing in development boards may sell a few accessories for their boards, but usually leave product design to their customers. Next Thing Co. does that too, but the company also produces some products like PocketCHIP portable Linux computer & retro game console, and more recently Dashbot, a voice controller assistant for your car’s dashboard powered by CHIP Pro module. Dashbot hardware specifications: CPU Module – CHIP Pro with Allwinner GR8 ARM Cortex A8 processor @ 1.0 GHz, 512MB NAND flash, 256 DDR3 RAM, 802.11 b/g/n WiFi, Bluetooth 4.2 External Storage – micro SD slot Display – Red LED display Audio – 32-bit audio DSP for beamforming & noise suppression; fairfield audio pre-processor with 24-bit ADC; high fidelity MEMS microphone array (106 dB dynamic range) USB – 1x USB host port Power Supply – 5V via USB port or 12V via power port (aka cigarette lighter) + backup LiFePo4 […]

November 17, 2016September 20, 2017 by Jean-Luc Aufranc (CNXSoft) - 21 Comments

Khadas Vim Amlogic S905X Android and Linux Development Board Sells for $50 and Up

Last summer I wrote about Shenzhen Tomato TVI development board powered by Amlogic S905X processor, and at the time the company focused on business to business customers, but the board is now sold as Khadas Vim through GearBest with 2 GB RAM, 8 or 16 GB flash, and price starting at $49.99 including shipping. Khadas Vim and Vim Pro boards’ specifications: SoC – Amlogic S905X quad core ARM Cortex-A53 @ up to 1.5 GHz with penta-core Mali-450MP GPU System Memory – 2 GB DDR3 Storage Vim – 8 GB eMMC flash + micro SD slot Vim Pro – 16 GB eMMC flash + micro SD slot Video & Audio Output – HDMI 2.0a up to 4K @ 60 Hz Connectivity Vim – Fast Ethernet port, 802.11 b/g/n WiFi and Bluetooth 4.0 (Ampak AP6212 module) with IPEX connector Vim Pro – Fast Ethernet port, dual band 802.11 b/g/n/ac WiFi and Bluetooth […]