usb

Posted on by Tomisin Olujinmi - 2 Comments on Tillitis Tkey is an open-source RISC-V security key in a USB-C case

Tillitis Tkey is an open-source RISC-V security key in a USB-C case

Tkey security key with an open lid

Tillitis’ TKey is a small, simple security key in a USB-C form factor, and described as a “new type of flexible USB security token” that is inspired by DICE (Device Identifier Composition Engine) and measured boot powered by a simple 32-bit RISC-V core, the PicoRV32, in a Lattice iCE40 UP5K FPGA. While we have covered hardware security modules in the past, this is the first security key we have seen that is based on an FPGA running a RISC-V core. The security token lacks persistent, onboard storage, unlike alternatives such as Yubikey Neo. Apps need to be loaded onto the key every time it is connected to a host device. It uses measured boot to generate a unique identifier for each application and is more secure than the alternatives since private keys are not stored on the device. Also, the hardware and software for the TKey are completely open-source for […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 3 Comments on $44 5G M.2 to Ethernet and USB “converter” takes M.2 5G PCIe modules

$44 5G M.2 to Ethernet and USB “converter” takes M.2 5G PCIe modules

5G M.2 to Ethernet and USB converter

Waveshare “5G M.2 to Gigabit Ethernet converter, 5G M.2 to USB3 converter” is a single device designed to easily and cheaply add 5G connectivity to a LAN through a gigabit Ethernet port or to a specific host like a PC or a Raspberry Pi SBC through a USB 3.1 Type-C port. The 5G M.2 to Ethernet and USB converter is flexible as by default it does not ship with a 5G module, but features an M.2 Key-B socket for 5G 3042 or 3052 modules allowing it to meet the requirements of a specific location. 5G M.2 to Ethernet and USB converter key features and specifications: Cellular M.2 Key B socket for 3042/3052 5G modules from SIMCom (SIM82XX), Quectel (RM5XX), and Fibocom (FM160XX) Onboard standard SIM card slot 4x 5G omnidirectional high-gain antennas Ethernet – Gigabit Ethernet RJ45 port using RealTek RTL8125 controller USB – USB 3.1 Type-C port for connection […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on T-Keyboard-S3 4-key USB mechanical keyboard features keycaps with 0.85-inch color display

T-Keyboard-S3 4-key USB mechanical keyboard features keycaps with 0.85-inch color display

T-Keyboard-S3

LILYGO T-Keyboard-S3 is an ESP32-S3 powered USB mechanical keyboard with four keys each equipped with a keycap featuring a 0.85-inch 128×128 color display to show different icons or characters. We have already covered several programmable small mechanical keyboards/keypads or macropads, so the first time I saw the T-Keyboard-S3 I did not think much of it until I read the $65 price tag on Aliexpress which I found excessive for this type of device. That’s only until I realized that each resin keycap has its own color display that the price made sense, and it makes quite a versatile macropad as you could easily program multiple layouts depending on the use case. T-Keyboard-S3 specifications: Wireless module ESP32-S3-WROOM-1 MCU – ESP32-S3R8 dual-core LX7 microprocessor @ up to 240 MHz with Vector extension for machine learning Memory – 8MB PSRAM Storage – 16MB SPI flash Connectivity – WiFi 4 and Bluetooth 5 with LE/Mesh […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on How to use a monitor and USB mouse/keyboard in Promox VE on an Intel Alder Lake-N mini PC

How to use a monitor and USB mouse/keyboard in Promox VE on an Intel Alder Lake-N mini PC

Intel Core i3-N300 Alder Lake-N Ubuntu 22.04 Promox VE passthrough

We’ve started to see several Alder Lake-N platforms acting both as a mini PC and a router or network appliance with products such as iKOOLCORE R2 or CWWK x86-P5 which features not only the usual HDMI, USB, and single Ethernet port, but come with multiple Ethernet ports making them ideal to run Proxmox VE to simultaneous run a desktop OS such as Ubuntu 22.04 or Windows 11 and a headless network OS such as pfSense or OpenWrt. I’m currently reviewing iKOOLCORE R2 mini PC that comes with four 2.5GbE ports and I could install Ubuntu 22.04 Desktop, pfSense 2.7.1, and OpenWrt 23.05 relatively easily, but the Ubuntu desktop is only visible in the Proxmox VE dashboard and the HDMI display physically connected to the mini PC only shows Proxmox VE login prompt. So at this point, I learned that I had to enable PCIe passthrough for the GPU in Proxmox […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 10 Comments on PicoUART6 6x UART to USB bridge supports up to 6 Raspberry Pi 5 boards

PicoUART6 6x UART to USB bridge supports up to 6 Raspberry Pi 5 boards

PicoUART6 Raspberry Pi 5 UART USB bridge

PicoUART6 is a small USB to UART bridge board that takes a Raspberry Pi Pico board and exposes six UART ports to connect up to six Raspberry Pi 5 SBC’s over the new 3-pin UART connector. The Raspberry Pi 5 has created a lot of buzz since its announcement in September 2023, and people most talked about its higher performance compared to a Raspberry Pi 4 and its new (non-standard) FCP PCIe connector,  but the new Raspberry Pi SBC also features a 3-pin JST UART connector that was not used in earlier and frees 3-pin on the 40-pin GPIO header. The PicoUART6 board makes use of this new connector to interface multiple Raspberry Pi 5 over UART and control them through the USB board of the Pico board. PicoUART6 specifications: Footprint for Raspberry Pi Pico board Serial – 6x 3-pin JST UART connectors Expansion – STEMMA QT/Qwiic I2C connector Debugging […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on Tiny Raspberry Pi RP2040 module connects to USB-C + buttons board via FPC connector

Tiny Raspberry Pi RP2040 module connects to USB-C + buttons board via FPC connector

Raspberry Pi RP2040 module with FPC USB-C board

Waveshare RP2040-Tiny is another tiny Raspberry Pi RP2040 module that joins others like Pimoroni Tiny 2040, DFRobot Beetle RP2020, or Solder Party RP2040 Stamp, but with a twist as the solderable module features an FPC connector in order to optionally connect a separate board with a USB-C port as well as Boot and Reset buttons. This design enables the convenience of having a USB-C port for power and programming, plus the Reset and Boot buttons during firmware development, and developers can only keep the tiny and ultrathin module when integrating it into a project or product. Alternatively, there may be designs that benefit from having the USB-C port located further away from the main module with all I/Os, and it can also facilitate troubleshooting when the product is already integrated into a product. Waveshare RP2040-Tiny specifications: MCU – Raspberry Pi RP2040 dual-core Cortex-M0+ microcontroller @ up to 133Mhz with 264kB […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 3 Comments on Raspberry Pi 5 gets 5G Modem HAT based on Quectel RM502Q-AE M.2 module

Raspberry Pi 5 gets 5G Modem HAT based on Quectel RM502Q-AE M.2 module

Sixfab 5G Modem Kit for Raspberry Pi 5

Sixfab has just launched a 5G Modem Kit for Raspberry Pi 5 with a Raspberry Pi HAT that takes Quectel RM502Q-AE 5G Sub-6GHz M.2 module working globally (except China), a “patent-pending” internal antenna for Sub-6 frequency bands designed by SixFab, and a USB 3.0 bridge connector. SixFab 5G modem Kit for Raspberry Pi 5 highlights: Sixfab 5G Modem HAT for Raspberry Pi 5 M.2 socket for 5G module Nano SIM card holder + embedded SIM USB 3.0 port and 40-pin GPIO header for connection to the Raspberry Pi 5 SBC Misc User button Status, power, and user (GPIO21) LEDs EEPROM for Raspberry Pi HAT compliance 2-pin fan connector Power Supply – 5V via USB Type-C port (on HAT itself) Dimensions – 88.1 x 57.7 x 21.7 mm Approvals – FCC, IC, CE, UKCA are in progress Quectel RM502Q-AE M.2 module 5G NR: 3GPP Release 15 NSA/SA operation, Sub-6 GHz LTE […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 6 Comments on WP-DLC01 USB RGB LED controller supports dynamic lighting (in Windows 11 for now)

WP-DLC01 USB RGB LED controller supports dynamic lighting (in Windows 11 for now)

WisdPi USB Dynamic Lighting controller

WisdPi WP-DLC01 dynamic lighting controller is a small USB board that can drive RGB LED strips and supports the Dynamic Lighting feature just introduced in the latest Windows 11 23H2 release. The board comes with a WisdPi RGB213-5 chip, a button, a USB-C port for control, and a 3-pin header designed to connect an ARGB LED strip which the user can place inside a PC or along a desk or table to personalize the user experience beyond the screen. Right now this works in Windows 11 23H2, but as we’ll see further below it should (eventually) work with other operating systems. The first step is to connect the controller either externally via a USB-C to USB-A/C cable or internally using the 15cm USB 2.0 internal motherboard header to USB Type-C cable provided with the WP-DLC01 board by default. WisdPi also offers a full kit that adds a 1-meter USB 2.0 […]