automation News - Page 12 of 56 - CNX Software

October 30, 2022October 30, 2022 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

SONOFF NSPanel Pro control panel review with Zigbee modules, CAM Slim WiFi camera

ITEAD has sent us a Smart Home kit for review including the SONOFF NSPanel Pro Android control panel and Zigbee gateway, an enclosure stand, the CAM Slim WiFi camera, and four Zigbee modules, namely the SNZB-01 wireless switch, the SNZB-02 temperature & humidity sensor, the SNZB-03 motion sensor, and the SNZB-04 door/window sensor. In this review, we’ll configure the NSPanel Pro controller with the eWelink app in Android, show how to add the WiFi camera and Zigbee devices directly to NSPanel Pro, and go back to the eWelink app for more advanced features such as scenes with triggers and actions. Sonoff NSPanel Pro kit unboxing Let’s get started by having a closer look at the SONOFF NSPanel Pro controller. As previously noted, the device is based on Rockchip PX30 quad-core Cortex-A35 processor and runs Android 8.1. It acts both as a control panel and a WiFi to Zigbee 3.0 gateway. The […]

October 24, 2022February 21, 2023 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Automation 2040 W board supports 6V to 40V I/Os, ships with Raspberry Pi Pico W

Pimoroni Automation 2040 W is an industrial/automation controller based on the Raspberry Pi Pico W board that supports I/Os from 6V up to 40V and offers 2.4GHz WiFi 4 connectivity. The board offers plenty of interfaces including the ADC inputs, four digital inputs, three digital outputs, and three relays whose signals are all available through screw terminals, as well as two Qwiic/STEMMA QT connectors for further expansion. Automation 2040 W specifications: Controller – Raspberry Pi Pico W with Raspberry Pi RP2040 dual-core Cortex-M0+ microcontroller @ 133 MHz with 264KB SRAM, 2MB flash, 802.11b/g/n WiFi 4 module I/Os 3x 12-bit ADC inputs up to 40V 4x digital inputs up to 40V 3x digital sourcing outputs at V+ (supply voltage) with 4A max continuous current 2A max current at 500Hz PWM 3x relays (NC and NO terminals) supporting 2A up to 24V, 1A up to 40V 3.5mm screw terminals for inputs and […]

October 14, 2022October 20, 2022 by Jean-Luc Aufranc (CNXSoft) - 13 Comments

Home Assistant launches SkyConnect USB stick with Zigbee, Thread, Matter support

The Home Assistant SkyConnect is a USB stick with support for Zigbee, Matter, and Thread connectivity designed to work with the popular Home Assistant open-source home automation solution, and enables users to bring Home Assistant Yellow (previously known as Home Assistant Amber) functionality to any platform running Home Assistant. The USB dongle is based on a Silicon Labs EFR32MG21 Gecko Series 2 Arm Cortex-M33 wireless microcontroller with an 802.15.4 multi-protocol 2.4 GHz radio that can concurrently run both Zigbee 3.0 (EmberZNet/EZSP) and Thread/Matter (OpenThread/Spinel) stacks/protocols at the same time by using firmware in RCP RCP (Radio Co-Processor) mode. Home Assistant SkyConnect specifications: MCU – Silabs EFR32MG21 Arm Cortex-M33 microcontroller @ up to 80 MHz with DSP and FPU, up to 1024 KB flash, up to 96 KB RAM, 2.4 GHz radio Wireless Protocols – Zigbee, Matter, Thread TX Power – up to +20dBm RX sensitivity – -104dBm (250kbps) 2.4 GHz […]

October 11, 2022October 12, 2022 by Jean-Luc Aufranc (CNXSoft) - 13 Comments

Tuya “T6E” is a 4-inch Android touch control panel & Zigbee gateway for OEMs

Tuya T6E is a 4-inch control panel with a touchscreen running Android 8.1 on Rockchip PX30, WiFi, Bluetooth, and Zigbee, and designed to be wall-mounted for home automation and other HMI applications. It looks fairly similar to the ITEAD NSPanel Pro introduced last month, for Tuya’s “Central Control System” (CSS) appears to be mostly designed for OEMs who want to roll their own products with custom firmware. Tuya T6E specifications (details vary depending on OEM requirements): SoC – Rockchip PX30 quad-core Arm Cortex-A35 processor @ up to 1.5GHz with Mali-G31 MP2 GPU System Memory – 1GB, 2GB, or 4GB RAM Storage – 4GB to 8GB eMMC flash Display – 4-inch 480×480 IPS screen with 5-point capacitive touch Audio Dual-array microphone with noise reduction 1 Watt speaker Connectivity 10/100Mbps Ethernet RJ45 port 2.4 GHz 802.11b/g/n Wi-Fi 4 Bluetooth LE 4.2 and Bluetooth Mesh (Tuya SigMesh) Zigbee 3.0 gateway based on Tuya […]

October 5, 2022October 5, 2022 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

RelayFi – A Tasmota compatible 4-channel relay board (Crowdfunding)

CoreData Global, a Singapore-based research and development firm, has just introduced the RelayFi 4-channel relay board based on ESP32 and compatible with Tasmota open-source firmware, as well as Espressif’s ESP RainMaker cloud and ESP-NOW networking API. RelayFi is fitted with an ESP32-WROOM-32D WiFi and Bluetooth module, four relays capable of handling a load of 250 VAC/7A or 30 VDC/10A, and EL817C Optoisolators for safety. The board also comes with CH340C USB to TTL chip for programming, an I2C header for expansion, and some jumpers for relay selection. RelayFi specifications: Wireless module – Espressif Systems’ ESP32-WROOM-32D module with ESP32 dual-core Tensilica microcontroller, 32Mbit SPI flash, Wi-Fi 802.11 b/g/n up to 150 Mbps, Bluetooth 4.2 LE, and PCB antenna Relays 4x relays up to 250VAC/7A or 30VDC/10A 4x EL817C optocouplers for safety 4x relay status LEDs Screw terminals Relay selection jumper USB – 1x micro USB port for power and programming via […]

September 22, 2022September 22, 2022 by Jean-Luc Aufranc (CNXSoft) - No Comments

OnLogic IGN800 Industrial Raspberry Pi Edge Gateway runs Ignition Edge software

OnLogic IGN800 is an industrial edge gateway based on the Raspberry Pi CM4 module pre-loaded with the Ignition Edge HMI, SCADA (Supervisory Control And Data Acquisition), MES, and IIoT software platform from Inductive Automation. The hardware is not exactly new, as the Onlogic IGN800 is simply the OnLogic Factor 201 industrial PC introduced earlier this year, but that ships with Ignition Edge in order to provide a cost-effective solution for automation projects. OnLogic IGN800 specifications: SoM – Raspberry Pi CM4 with Broadcom BCM2711 quad-core Arm Cortex-A72 processor @ up to 1.5 GHz, up to 8GB LPDDR4 RAM, up to 32GB eMMC flash Additional storage – Optional M.2 SATA SSD (See Expansion section) Video Output – HDMI port up to 4Kp60 Networking 2x Gigabit Ethernet LAN (Optional PoE PD Input) via Realtek RTL8153 controller Optional WiFi/Bluetooth module on Raspberry Pi CM4 module + 3x antenna holes Optional 4G LTE wireless module […]

September 9, 2022September 8, 2022 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

GENE-ADP6 – An 3.5-inch SBC with Intel 12th Gen Alder Lake-P processor, DDR5 RAM

AAEON GENE-ADP6 is a 3.5-inch SBC equipped with a choice of Intel 12th Gen Alder Lake-P (and Alder Lake-U) processors and the first from the company to support DDR5 memory, of which up to 64GB can be installed through two SO-DIMM sockets. The single board computer also supports SATA and NVMe storage, up to two 8K displays (and up to four independent displays), 2.5GbE networking, USB 3.2 ports, four RS232/RS422/RS485 interfaces, and further expansion through three M.2 sockets for wireless connectivity (WiFi, 5Gm, 4G LTE…) as well as the already mentioned NVMe SSD storage. GENE-ADP6 SBC specifications: Intel Alder Lake-P SoC (one or the other) Core i7-1270PE 12-core/16-thread processor @ 3.30GHz / 4.50GHz (Turbo) with 96EU Intel Xe graphics – PBP: 28W, up to 64W MTP Core i7-1265UE 10-core/12-thread processor @ 3.50GHz / 4.70GHz (Turbo) with 96EU Intel Xe graphics – PBP: 15W, up 55W MTP Core i5-1250PE 12-core/16-thread processor […]

August 31, 2022September 8, 2022 by Jean-Luc Aufranc (CNXSoft) - 8 Comments

ESPHome compatible ESP32-S2 module offers six 32A latch relays in a DIN Rail enclosure

EasySensors “6Gang30AmpsLatchRelayEspHomeReady” (now that’s a product name!) is a DIN Rail mountable, ESP32-S2-based automation device featuring six 32A latch relays and supporting ESPHome open-source framework. The system also comes with two inputs for Dallas temperature sensors, two buttons for manual control of relays, a USB-C port for programming, as well as an external SMA antenna for WiFi connectivity. 6Gang30AmpsLatchRelayEspHomeReady specifications: Wireless SoC – Espressif ESP32-S2 Xtensa single-core 32-bit LX7 microcontroller @ up to 240 MHz with 320 kB SRAM, 2.4 GHz WiFi 4 (Matter-ready) Antenna – Embedded IPX to SMA adapter, 3dBi antenna I/Os 6x 32A latch relays with zero current idle consumption 2x Dallas temperature sensor pins with 5 kOhm pull-up resistors USB – 1x USB Type-C for programming via CP2102 USB to TTL chip Misc 6x control buttons, Reset button 6x status LED’s, 2x status LED’s Input Voltage – 85 to 305V AC Dimensions Board – 147 x […]