wifi News - Page 12 of 113 - CNX Software

August 1, 2024August 1, 2024 by Sayantan Nandy - 1 Comment

NBIOT/LTE-M Air Monitor – A solar-powered ESP32-S3 multi-sensor board with SIM7080G NB-IoT & LTE-M modem

nbiotlte m air monitor air temperature humidity light co2

The NBIOT/LTE-M Air Monitor is a solar-powered device that utilizes a combination of ESP32-S3 and SIM7080G modules for remote environmental monitoring. It monitors and transmits environmental parameters such as temperature, humidity, CO2, TVOC, and light intensity using low-power wide-area network (LPWAN) technology ensuring efficient power consumption, durability, and reliable data transmission. Previously we have written about similar environment monitor devices like the Airlytix ES1, Sonoff SC WiFi, V-Air Monitro, and devices like Arduino MKR IoT Carrier Rev2, Radair mini gateway, and Nicla Sense ME designed for environment monitoring applications. Feel free to check those out if you are interested in this type of product. NBIOT/LTE-M Air Monitor specification Wireless Module – ESP32-S3-WROOM-1-N16R8 Espressif Systems ESP32-S3R8 – Dual-core Tensilica LX7 @ up to 240 MHz with vector instructions for AI acceleration, 512KB RAM, 8MB PSRAM Storage – 16 MB flash Wireless – 2.4 GHz WiFi 4 and Bluetooth PCB antenna Cellular connectivity Module – SIMCom SIM7080G LTE Cat […]

July 31, 2024July 31, 2024 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

Tuya Ivy smart flower pot monitors your plant’s inner feelings

No need to check the calendar, it’s not the first of April, and Tuya Ivy is indeed a smart WiFi-connected flower pot with a display that will report your plant’s thirst for water, need for more light, and even loneliness… Developed by PlantsIO, the Ivy smart flower pot is powered by an ESP32 wireless microcontroller connected to seven sensors including lighting and moisture sensors, and a display to show various faces. There’s also a USB-C port for power, a microSD card slot for data storage, some buttons, and a touch bar for user interaction. Tuya Ivy specifications: Wireless module – ESP32-WROVER-E SoC – ESP32 dual-core LX6 processor running at 240 MHz with 520KiB internal RAM Memory – 64 Mbit PSRAM (ESP PSRAM64H) Storage – 64Mbit SPI flash (XMC 25QH64CH10) Wireless – 2.4 GHz WiFi and Bluetooth 5.x (Only WiFi appears to be use) Storage – microSD card Display – Tri-color […]

July 30, 2024July 30, 2024 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

LILYGO T-ETH-ELite ESP32-S3 Ethernet PoE board supports stackable LoRaWAN and Cellular expansion modules

LILYGO T-ETH Elite ESP32-S3 Ethernet board LoRaWAN mPCIE cellular expansion

LILYGO T-ETH-Elite is an ESP32-S3-powered IoT board with an Ethernet RJ45 port supporting PoE and a 40-pin GPIO header for stackable shields that offer support for LoRaWAN, 2G, NB-IoT, or/and 4G LTE cellular connectivity. The ESP32-S3 board allows users to build gateways with Ethernet, WiFi, Bluetooth, GNSS, LoRaWAN, and Cellular (2G, NB-IoT, 4G LTE) connectivity, and they can easily switch cellular modules to match specific requirements. LILYGO T-ETH-Elite specifications: Wireless module – Espressif ESP32-S3-WROOM-1 MCU – ESP32-S3R8 dual-core Tensilica LX7 up to 240 MHz with 512KB SRAM, up to 8MB PSRAM Storage – 16MB flash Connectivity – WiFi 4 and Bluetooth LE 5 PCB antenna Storage – MicroSD card slot Networking – 10/100Mbps Ethernet RJ45 port via W5500 SPI to Ethernet chip USB – USB Type-C port for power and programming Expansion – 40-pin (mostly) Raspberry Pi-compatible GPIO header for shields (up to 23x GPIO, USB 2.0, UART, 5V, 3.3V, […]

July 26, 2024July 26, 2024 by Jean-Luc Aufranc (CNXSoft) - No Comments

T2-U WiFi and Bluetooth development board supports the Tuya Smart Home framework

The T2-U is a development board compatible with the Tuya Smart Home framework that features a WiFi and Bluetooth module with a 120 MHz RISC processor, some buttons, an LED indicator, GPIOs, power, and a USB-to-serial chip. In 2019, we covered Tuya as a one-stop Smart Home solution allowing companies to easily design and manufacture home automation devices from electronics to the enclosure. For example, the company provides a customizable 4-inch Android touch control panel & Zigbee gateway as well as the Tuya Link SDK allowing customers to further customize the firmware of their Smart Home devices, but I had yet to see a development board compatible with Tuya. T2-U development board specifications: Wireless module – T2-U SoC – Unnamed 32-bit RISC MCU @ 120 MHz with 2 MB flash and 256 KB RAM Wireless Wi-Fi 802.11b, 802.11g, and 802.11n wireless standard. Channels 1 to 14 at 2.4 GHz. Security […]

July 24, 2024August 30, 2024 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

LILYGO T-Halow is an ESP32-S3 board with long-range WiFi HaLow, OV2640/OV5640 camera support

LILYGO T-Halow is an ESP32-S3 board equipped with a WiFi HaLow module with up to 1.2km range, a connector compatible with OV2640 and OV5640 camera modules, and an 18650 battery holder for power, as well as several GPIOs for expansion. We first wrote about 802.11ah low-power long-range WiFi standard operating at 900 MHz in 2014, but adoption has been slow and we’ve seen a few 802.11ah (WiFi HaLow) chips from Newracom and Morse Micro over the years, as well as USB adapters, a Raspberry Pi HAT, a mini PCIe card, gateways, and some development boards. All those rely on a Linux host, but the LILYGO T-Halow features a TX-AH WiFI HaLow module from Taixin Semiconductor that’s controller by AT commands through an ESP32-S3 or a micro USB port. LILYGO T-Halow specifications: Wireless modules ESP32-S3-WROOM-1 wireless module SoC – ESP32-S3 dual-core Tensilica LX7 microcontroller @ up to 240 MHz with 2.4 […]

July 24, 2024 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Remote.It adds Bluetooth assisted WiFi configuration to Raspberry Pi SBC’s

Remote.It, a company providing remote access services, has released an open-source project to enable Raspberry Pi WiFi network configuration using Bluetooth (BLE), so users can easily configure WiFi on the board by simply using their smartphone. Configuring WiFi on a Raspberry Pi usually involves either: Manual configuration – The user connects a monitor and keyboard to the Raspberry Pi to configure the wireless network directly on the device. Pre-configured SD cards, NVMe SSDs, or USB drives – The WiFi ESSID and password can be set in Raspberry Pi USB imager, and the Raspberry Pi will automatically connect to the network at boot time. That’s quick, but less flexible since the credentials can’t be modified after deployment, and it only works when using a single wireless network. Remote.It offers a third option for WiFi provisioning using Bluetooth LE. The Raspberry Pi can run headless or fully enclosed into a product, and […]

July 24, 2024July 23, 2024 by Jean-Luc Aufranc (CNXSoft) - 9 Comments

LOLIN S3 Mini Pro – A tiny ESP32-S3 board with a 0.85-inch display and a multi-color PCB

LOLIN S3 Mini Pro is a tiny ESP32-S3 WiFi and BLE board with a 0.85-inch display and it’s one of the first boards I’ve seen with a multi-color PCB that some PCB manufacturers have been offered recently. The board features an ESP32-S3FH4R2 microcontroller with 4MB flash and a 2MP PSRAM, a 128×128 TFT display, a 6-axis motion/attitude sensor, and GPIO headers that make it compatible with LOLIN D1 mini shields for expansion. LOLIN S3 Mini Pro specifications: SoC – Espressif Systems ESP32-S3FH4R2 CPU – Dual-core Tensilica LX7 microcontroller @ up to 240 MHz Wireless – 2.4 GHz 802.11n WiFi 4 and Bluetooth 5.0 LE connectivity Memory – 2MB PSRAM Storage – 4MB SPI flash Display – 0.85-inch 128×128 LCD TFT display with GC9107/GC9A01 driver Sensor – 6-axis MEMS IMU/attitude sensor (QMI8658C) Expansion 2x 8-pin headers with up to 12x GPIO, ADC, DAC, I2C, SPI, UART, USB OTG; compatible with LOLIN […]

July 17, 2024July 17, 2024 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

StackyFi ESP32-S3 board features camera connector, 40-pin GPIO header for Raspberry Pi HAT (Crowdfunding)

StackyFi ESP32-S3 Raspberry Pi Zero board

SB Components’ StackyFi is an ESP32-S3 WiFi and Bluetooth IoT board with a 40-pin GPIO header compatible with most Raspberry Pi HAT expansion boards and a camera connector for image capture to a microSD card or machine learning applications. The Raspberry Pi Zero-sized board also comes with two USB Type-C ports, one “native” and the other for serial debugging, an IMU sensor, an RGB LED, and Boot and Reset buttons. The board can be powered through one of the USB-C ports or a LiPo battery. It partially builds upon the earlier StackPi board with a Raspberry Pi RP2040 microcontroller. StackyFi specifications: Wireless module – ESP32-S3-WROOM-1 MCU – ESP32-S3 dual-core Tensilica LX7 up to 240 MHz with 512KB SRAM Memory – TBD PSRAM Storage – TBD flash Wireless – WiFi 4 and Bluetooth LE 5 PCB antenna Storage – MicroSD card Camera I/F – FPC connector that works with OV2640 camera […]