Category: NXP LPC

Posted on by Jean-Luc Aufranc (CNXSoft) - 7 Comments on $25 Outbreak Galago – Cortex M3 Open Hardware Development Kit

$25 Outbreak Galago – Cortex M3 Open Hardware Development Kit

Outbreak Galago is a tiny development kit based on a Cortex M3 processor that fits a debugger, and is destined for rapid electronics prototyping. The company promotes it as some sort of Arduino board on steroid (MCU wise) and sells for $25 on kickstarter, and less than $10 in 10k quantities. Here are the board specifications: 72 MHz 32-bit ARM CPU with 32KB of flash ROM and 8KB of RAM (NXP LPC1313 TBC) Integrated hardware debugger One high-speed SPI port, up to 36 Mbps One high-speed I2C port, up to 1.5 Mbps One UART/USART with hardware flow-control capability, up to 256 kbps 10 high-speed PWM pins, 6 driven by 32-bit (high-resolution) timers 6 ADC (analog) input pins with 10-bit resolution at over 400 KSa/sec 25 GPIO (digital) input/output pins The form factor and built-in debugger (via USB) are not really new, as those are already featured in devkit such as TI Piccolo controlSTICK, […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 1 Comment on Adafruit mbed and NFC/RFID Starter Pack with µNFC stack & NFC Mood Lamp Demo

Adafruit mbed and NFC/RFID Starter Pack with µNFC stack & NFC Mood Lamp Demo

If you are looking for a (relatively) low cost NFC development kit, you may interested in Adafruit mbed and NFC/RFID Starter Pack that sells for 134.99 USD. The kit contains the following items: mbed LPC1768 (Cortex M3) development board with mini-B USB cable and reference cards NFC/RFID breakout board based on PN532 NFC transceiver MiFare RFID card with 1K programmable EEPROM Full-sized breadboard 40 x 3″ (75mm) long male/male jumper wires Standard blue & white 16×2 character LCD + contrast potentiometer + header Diffused 5mm RGB LED + 3 x 560 ohm resistors Analog temperature sensor (TMP36) Piezo buzzer 2 x 10K trim potentiometer 5 x Tactile Pushbuttons On the software side, you can use AppNearMe µNFC stack written in C++ that allows you to use a user interface on NFC-enabled smartphone, removing the need for knobs, buttons, screens on your embedded device. During the initial pairing, the NFC board can […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 1 Comment on Embedded Artists NXP LPCXpresso Motor Control Kit Promotion

Embedded Artists NXP LPCXpresso Motor Control Kit Promotion

Embedded Artist and NXP have jointly designed the LPCXpresso Motor Control Kit to easily get started with motor control prototyping. This platform is based on NXP LPCXpresso MCUs and can control BLDC (Brushless DC), BLAC (Brushless AC), stepper and dual brushed DC motors. This is not a new design (2010), but Embedded Artist and NXP are discounting their development kit by 50% for a limited period, which brings the price of the kit to 149 Euros, instead of 299 Euros. The kit includes: LPCXpresso Motor Control Board LPCXpresso LPC1114 Board (The “stick” on the left in the picture above) LPCXpresso Eclipse-based IDE and GNU compiler BLDC Motor with hall sensors 24V Power supply (60W) Here are the specifications of the Motor Control Board: Controller MCU • Socket for LPCXpresso LPC1114 and LPC1343 • Socket for LPCXpresso LPC176x • Socket for LPC1xxx in PLCC44 • Expansion connector for control by LPC1800/LPC4000/LPC2900 […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on Embedded Artists and NXP Release The First ARM Cortex-M Android Open Accessory Development Kit

Embedded Artists and NXP Release The First ARM Cortex-M Android Open Accessory Development Kit

Embedded Artists and NXP introduced the TN-20764, a board that can be used with Android Open Accessory Application (AOAA) development kit that features 2 NXP Cortex-M MCUs, at Embedded World 2012. The board includes Ethernet, CAN and IEEE 802.15.4 interfaces as well as a remote CAN node, enabling designers to develop accessories for consumer applications,  as well as home, building and industrial automation applications requiring different types of connectivity. There are already Arduino and PIC-based Android Open Accessories, but this board is the first AOAA kit based on ARM Cortex-M micro-controllers. As mentioned above, the board features 2 Cortex M micro-controllers: The NXP LPC1769, a 120-MHz Cortex-M3 based MCU, provides the interface to the Android mobile device via its full-speed USB transceiver . The LPC1769 also includes 512 KB flash and 64 KB on-chip SRAM, an Ethernet MAC, a CAN 2.0B controller, an 8-channel, a 12-bit ADC, a 10-bit DAC, […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 2 Comments on Play Angry Birds For Real with Mbed NXP Cortex-M0 Slingshot

Play Angry Birds For Real with Mbed NXP Cortex-M0 Slingshot

If you’re just bored to play Angry Birds with the touchscreen of your smartphone or with your mouse in Angry Birds for Chrome, you can now bring the fun back to the game by playing with a real slingshot ! mbed designed a USB slingshot with an mbed NXP LPC11U24 (Cortex-M0 MCU) board that emulates a USB mouse. mbed measures the angle and strength applied with: An accelerometer that measure the tilt by tracking the gravity vector A rubber stretch sensor used as the sling, and measure how much it is stretched. They built the slingshot with the following hardware components: mbed NXP LPC11U24 board – 59 USD 3-axis Accelerometer – ADXL345 Accelerometer connect via SPI  – 14.95 USD Stretch Sensor connected to pin 15 (analog input) – 9.95 USD USB B connector Handcrafted Slingshot Here’s how mbed describes their NXP board: The mbed NXP LPC11U24 MCU module is a […]