Video Category - Page 67 of 331 - CNX Software

January 9, 2022 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Reolink Go Plus 4G review – Part 2: A Solar-powered 4G LTE security camera with person & vehicle detection

Last month, I received Reolink Go Plus 4G smart security camera with 4G LTE connectivity, vehicle/human detection support, and powered by a solar panel. In the first part of the review, I did an unboxing, added the camera to the Reolink Android app, and confirmed it worked with my DTAC SIM card. I’ve now installed the camera and had time to test more of its features, so I can report my experience with the security camera. Reolink Go Plus 4G camera and solar panel installation I wanted to use the camera near the gate that’s outside of (reliable) WiFi range. So I found a piece of hardwood to which I attached the mounts of the camera and solar panel… … and attached it to the wall. My current installation works for testing, but it’s not the most secure as the camera is quite visible and only placed a little over […]

January 7, 2022January 7, 2022 by Jean-Luc Aufranc (CNXSoft) - 8 Comments

Board with 25 RGB LEDs is offered with ESP32-C3 or ESP32-Pico-D4

In case you are in need of a tiny WiFI or Bluetooth-connected board with an RGB LED matrix, two have shown up on Banggood with basically the same 25 RGB LED design , except “C3FH4 RGB” board is based on ESP32-C3 RISC-V SoC, while the other, named “PICO D4 RGB“, features ESP32-Pico-D4 SiP (System-in-Package). The boards are cute and the main purpose is probably for decoration/ornament, but I’d imagine if you purchase a few they could also be used as an experimentation/education platform for mesh networking, using the ESP Mesh Development Framework (ESP-MDF) for instance. C3FH4 RGB / PICO D4 RGB board specifications: SoC/SiP C3FH4 RGB board – ESP32-C3FH4 SoC with RISC-V core @ 160 MHz, 4MB flash, 2.4GHz Wi-Fi, and Bluetooth 5 LE with Long-Range support PICO D4 RGB board – ESP32-PICO-D4 system-in-package with ESP32 dual-core Xtensa processor @ 240 MHz, 2.4GHz Wi-Fi and Bluetooth dual-mode, 4MB flash Ceramic […]

December 29, 2021December 29, 2021 by Sponsored Post - 10 Comments

10,000 mAh Graphene power bank fully charges in 27 minutes (Sponsored)

Most power banks are made of Lithium batteries that charge in 3 to 4 hours and are good for around 500 charge cycles. But Elecjet Apollo Ultra is a different beast equipped with a 10,000 mAh Graphene battery that enables fast charging in just 27 minutes and offers a much longer lifespan with over 2,500 charge cycles. In other words that means Apollo Ultra power bank is 5x faster and lasts 5x longer than most lithium-based power banks. Another way to look at it is that this graphene-enhanced 10,000mAh power bank can gather enough power in just 7 minutes to fully charge your phone. It can fast-charge your phone up to three times, charge two devices at once, and passthrough charging lets you charge Apollo Ultra at the same time. Elecjet Apollo Ultra specifications: Battery Capacity – 10,000 mAh or 40 Wh Full Charge Time – 27 minutes USB ports […]

December 29, 2021 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Raspberry Pi UPS HAT takes two 18650 batteries (Crowdfunding)

Raspberry Pi UPS solutions have been available for years with products like PiJuice Zero, PiVoyager, or LiFePO4wered/Pi+. But the team at SB Components has designed another UPS HAT for Raspberry Pi with a holder for two 18650 batteries. The HAT is designed for 5V operation up to 2.5A, connects with the Raspberry Pi SBC through the I2C bus from the 40-pin GPIO header, and is equipped with a 0.91-inch OLED for information display. UPS HAT for Raspberry Pi specifications: Power Input – 8.4V/2A via DC jack Power Output – 5V up to 2.5A through LDO chip (GPIO header and 2x USB ports) Display – 0.91-inch OLED Host interface – I2C Misc – On/Off switch Battery support 18650 Lithium battery (not included) via holder for two batteries Battery reverse indicator Charging and voltage monitoring via TI INA219 I2C chip Battery voltage balancing with Hycon HY2213 Battery protection IC (Hycon HY2120) Dimensions […]

December 24, 2021December 24, 2021 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

Newt 2.7-inch wireless display offers high refresh rate with SHARP’s Memory-in-Pixel (MiP) technology (Crowdfunding)

Newt is a battery-powered, always-on, ESP32-S2 wireless display with a 2.7-inch display leveraging SHARP’s Memory-in-Pixel (MiP) technology to provide an experience similar to E-Ink displays but with a much faster refresh rate. The wireless display can connect to the Internet to retrieve weather, calendars, sports scores, to-do lists, quotes, and whatever you’d like. Since it is powered by an ESP32-S2 microcontroller you can program with the ESP-IDF framework, Arduino, MicroPython, or CircuitPython. Newt display specifications: WiFi module – Espressif ESP32-S2-WROVER module with ESP32-S2 single-core Xtensa LX7 processor @ 240 MHz with 4 MB flash and 2 MB PSRAM Display – 2.7-inch, 240 x 400 pixel SHARP MiP LCD with “high-contrast, high-resolution, low-latency content with ultra-low power consumption”, reflective mode to eliminate the need for a backlight. USB – 1x USB Type-C port for programming, power, and charging Expansion – I2C Qwiik connector Misc Micro Crystal RV-3028-C7 RTC (45nA power consumption) […]

December 23, 2021December 23, 2021 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

HUENIT modular robot arm takes 3D printer, laser engraver, suction, AI camera modules (Crowdfunding)

Most robot arms are designed to carry and manipulate payloads, but HUENIT modular robot arm is much more versatile as besides a traditional suction module, the robot supports modules such as a 3D printer, laser engraver, pen holder for drawings, and a creator module for let people designed their own. The robot arm can hold payloads of up to 750 grams, have a reach of up to 39 cm without module, supports WiFi and Bluetooth connectivity, and can also optionally be fitted with a 2MP AI camera module based on Kendryte K210 RISC-V processor with built-in AI accelerators. HUENIT specifications: Robot arm 4-axis Payload up to 750 grams Reach – 390mm without module Repeatability – 0.05mm Precision – 0.1mm Speed – Up to 500mm/s Storage – MicroSD card slot USB – 1x USB-C port Wireless – WiFI and Bluetooth Misc – UART, external stepper Power Supply – 24V DC input, […]

December 22, 2021December 23, 2021 by Jean-Luc Aufranc (CNXSoft) - 14 Comments

ESP32 UWB board features DW1000 module for accurate indoor positioning

FiRa “Fine Ranging” UWB technology was introduced a few years ago and is now found in devkits and Apple U1 chip. Makerfabs ESP32 UWB board provides another option with Espressif ESP32-WROVER-32 or ESP32-WROOM-32 WiFi & Bluetooth module combined with a Decawave DW1000 module for precision tracking. Makerfabs explains the board acts like a continuously scanning radar that locks onto another device (called Anchor, since it’s usually in a fixed location) and communicates with it to determine the distance between objects by calculating the time of flight (ToF) between devices, or in other words, the roundtrip time of challenge/response packets. ESP32 UWB board specifications: Wireless modules: WiFi & Bluetooth LE – ESP32-WROVER-32 or ESP32-WROOM-32 module with ESP32 dual-core processor @ 240 MHz UWB – B&T BU01 module based on Decawave DW1000 chip; IEEE802.15.4-2011 UWB compliant wireless transceiver module with a precision of 10cm indoors, a data rate of up to 6.8 […]

December 21, 2021December 21, 2021 by Jean-Luc Aufranc (CNXSoft) - 13 Comments

$65 dual Wi-Fi HaLow gateway kit extends network range by hundreds of meters

I’m starting to better understand what Wi-Fi HaLow (aka 802.11ah) is for, after seeing a kit with two WiFI HaLow gateways used to wirelessly extend the range of Ethernet connected nodes on the LAN, including IP cameras, to several hundred meters, far more than your typical WiFi repeater, but at the cost of a lower bitrate. Yesterday, I wrote about Halo TD-XPAH, the first easily procurable 802.11ah WiFi HaLow development board I had seen, since the introduction of the new standard in 2014. But I was told another lower-cost HaLow board had been available for a few months on Alibaba, and while I failed to find it on Aliexpress, I discovered a pack with two WiFi HaLow to Ethernet gateway that could easily help extend the range of WiFi nodes like security cameras and selling for about $65 shipped. STK-AH9066 WiFi HaLow gateway specifications: Wireless 802.11ah Wi-Fi HaLow standard 902-930MHz […]