development board News - Page 218 of 260 - CNX Software

March 13, 2015March 13, 2015 by Jean-Luc Aufranc (CNXSoft) - 15 Comments

Radxa Rock Lite Board Price Drops to $39

When the new Radxa Rock Lite was announced for $59 in September 2014, it was one of the most inexpensive quad core ARM Linux development board available on the market. But ODROID-C1 board in December 2014, and especially Raspberry Pi 2 board in February 2015 changed all that, as these two quad core boards sell for $35 before shipping and taxes. So the company has now decided to drop the price to $39 for the Radxa Rock Lite board. Let’s remind us of Radxa Rock Lite specifications: SoC – Rockchip RK3188 ARM Cortex-A9 quad core @ 1.6Ghz + Mali-400 MP4 GPU System Memory – 1GB DDR3 @ 800Mhz Storage – micro-SD SDXC up to 128GB Video Output – HDMI 1.4 up to 1080p@60hz, and AV output. LVDS interface. Connectivity – 10/100M Ethernet port, WiFi 150Mbps 802.11b/g/n with antenna Audio I/O – Audio S/PDIF, headphone jack Camera – CSI interface USB […]

March 12, 2015August 4, 2022 by Jean-Luc Aufranc (CNXSoft) - 14 Comments

Qualcomm Dragonboard 410c is Another 96Boards Compliant 64-bit ARM Development Board

Linaro announced the 96Boards initiative at Linaro Connect Hong Kong last month, and in collarabation with Huawei announced Hikey development board following this new standard. Qualcomm has now joined the Fray with Dragonboard 410c, a 96Boards board powered by Qualcomm Snapdragon 410 quad core Cortex A53 processor. Dragonboard 410c specifications: SoC- Qualcomm Snapdragon 410 (APQ8016) quad-core ARM CortexA53 @ 1.2 GHz with Adreno 306 GPU @ 400MHz System Memory – LPDDR2/3 533MHz, Single-channel 32-bit (4.2GBps) Storage – eMMC 4.51 + micro SD 3.0 (UHS-I) Video Output – HDMI up to 1080p Connectivity – Integrated 802.11 b/g/n, BT/FM, GPS USB – 2x USB 2.0 host ports, 1x micro USB OTG port. Camera – Support for 13 MP camera with Wavelet Noise Reduction, JPEG decoder, and other post-processing techniques done in hardware Expansion: 1x 40 pin low speed expansion connector – UART, SPI, I2S, I2C x2, GPIO x12, DC power 1x 60 […]

March 12, 2015 by Jean-Luc Aufranc (CNXSoft) - No Comments

Compulab Announces CM-T43 CoM and SBC-T43 Board Powered by TI Sitara AM437x Processors

Compulab has just introduced CM-T43 computer-on-module (CoM) powered by Texas Instruments Sitara AM437x ARM Cortex A9 processor and built-in wired and wireless connectivity, and targeting networking, industrial communications and IoT applications. The company has also announced the corresponding SBC-T43 single board computer featuring the module plus a baseboard. Compulab CM-T43 Module CM-T43 CoM specifications: SoC – Texas Instruments Cortex-A9 Sitara AM4376 / AM4379 SoC up to 1GHz with PowerVR SGX530 GPU (AM4379 only) System Memory – Up to 1GB DDR3 Storage – 4GB to 32GB on-board eMMC, 128MB to 512MB on-board SLC NAND Connectivity – 2x Gigabit Ethernet PHY, and Marvell 88W8897 chipset for dual-band, dual-antenna 2×2 MIMO 802.11ac/a/b/g/n WiFi, Bluetooth 4.0 Low Energy, and NFC (ISO 14443A/B, ISO 18092 and ISO 15693) Audio codec – Wolson Audio codec with stereo line-out, line-in, mic via edge connector 204-pin SO-DIMM edge connector with access to: USB2.0 high-speed dual-role (host / device) port, […]

March 12, 2015March 14, 2015 by Jean-Luc Aufranc (CNXSoft) - 191 Comments

Giveaway Week – Freescale SABRE Lite Development Board

Here’s a development board for a change. Freescale SABRE Lite is a board powered by Freescale i.MX 6Quad processor that I got during a giveaway organized on Element14… It’s a great board for Linux development thanks to the extensive documentation released by Freescale. After writing a short unboxing and quick start guide post, I planned to try a few more things on the board, but as I ended up owning Wandboard Dual and Quad boards, the mbest made board ended up collecting dust, so it’s much better to give it to somebody who certainly make good use of it. The box will have most items shown above, except the serial NULL cable which I keep for other experiments. The rules are the same as usual, simply leave a comment below to enter the draw. Other rules are as follows: Only one entry per contest. I will filter out entries with […]

March 10, 2015March 12, 2015 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

$35 Tessel 2 IoT Board Features Atmel SAMD21 MCU and Mediatek MT7620n WiSoC

Tessel is a Wi-Fi IoT board based on NXP LPC1830 Cortex M3 MCU and Texas Instruments CC3000 modules, that’s designed to bring embedded development to web programmers with a system that can be programmed with JavaScript and Node.js. At the time of the crowdfunding campaign in 2013, the board was available with external modules (Relays, sensors, Bluetooth LE…) for $100 and up, but now Technical Machine, the company behind the project, has announced Tessel 2 combining Atmel SAMD21 Cortex M0+ to control I/O and Mediatek MT7260n for Wi-Fi connectivity, still programmable with JavaScript ot Node.js. Tessel 2 specifications: MCU – Atmel SAMD21G14A-MU Cortex M0+ MCU @ 48MHz with 16KB SRAM and 2KB Flash SoC – Mediatek MT7260n MIPS24KEc Wi-Fi SoC @ 580 MHz System Memory – 64MB DDR2 Storage – 32MB flash for firmware (OpenWRT) Connectivity – 10/100M Ethernet, and Wi-Fi 802.11 b/g/n with dual PCB antennas USB – 2x […]

March 5, 2015March 5, 2015 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

ARM Cortex M0+ Based Arduino Zero Pro Board Gets Listed on Arduino.org

A new “Arduino Zero Pro” board has been listed on Arduino.org, which looks very similar to the Arduino Zero board announced last year, with Atmel ATSAMD21G18 ARM Cortex M0+ MCU, and that is still listed as “Coming Soon” on Arduino.cc website. So it feels a little odd Arduino would release a board with basically the same features. Arduino Zero Pro key specifications are indeed exactly the same: Microcontroller – Atmel ATSAMD21G18 32-bit ARM Cortex M0+ MCU @ 48 MHz with 32 KB SRAM, 256 KB flash, up to 16KB EEPROM (By emulation). 48-pin LQFP package. Digital I/O Pins – 14, with 12 PWM and UART Analog Input Pins – 6, including 5 12bits ADC channels and one 10 bits DAC DC Current per I/O Pin – 7 mA USB – 2x micro USB ports Debugging – USB via Atmel’s Embedded Debugger (EDBG) on-board debugger, and JTAG Misc – reset button, […]

March 4, 2015May 29, 2017 by Jean-Luc Aufranc (CNXSoft) - 12 Comments

Mixtile LOFT-Q Allwinner A31 Board with SATA Can Now be Purchased for $90

Mixtile LOFT-Q and LOFT Kit were unveiled nearly a year ago, the first being a development board based on Allwinner A31 processor with 2GB RAM, 16GB RAM, SATA connector, Gigabit Ethernet, etc.., while the second is a kit with an enclosure and power supply. The kit does not appear to be available yet, but the board has recently been listed on SeeedStudio for $90. Mixtile LOFT-Q specifications: SoC – Allwinner A31 quad core ARM Cortex-A7 processor with PowerVR SGX544 MP2 GPU System Memory – 2GB DDR3 Storage – 8GB eMMC, SATA III connector for 2.5″ drives, and SD card Slot Video Output – HDMI 1.4 up to 1080p60 Video Decoding – H.264 4Kx2K video decoding, multi-format FHD video decoding, including Mpeg1/2, Mpeg4 SP/ASP GMC, H.263, H.264,etc Audio I/O – HDMI, 1 S/PDIF, high definition microphone Camera I/F Integrated Parallel & MIPI I/F sensor Integrated powerful ISP, supporting Raw Data CMOS […]

March 3, 2015 by Jean-Luc Aufranc (CNXSoft) - 8 Comments

MYiR Tech Announces Low Cost Rico and Z-turn Boards Powered by TI AM437x and Xilinx Zynq-7010 SoCs

Shenzhen based MYIR Tech has just launched two new single board computers with Rico board featuring Texas Instruments Sitara AM437x ARM Cortex A9 industrial processor, and Z-Turn board based on Xilinx Zynq-7010 ARM Cortex A9 + FPGA SoC. Both boards sell for $99 in single quantity. Rico Board Specifications: SoC – Texas Instruments AM4379 single core ARM Cortex A9 processor @ 1.0GHz with PowerVR SGX530 GPU, and 4x PRU @ 200 MHz. Other AM437x on request. System Memory – 512MB DDR3 (Options: 256MB or 1GB) Storage – 4GB eMMC, 256 or 512 MB NAND flash (reserved), 16MB QSPI flash, 32KB EEPROM, and micro SD slot Video Output – HDMI and LCD interfaces (LCD connector located on bottom of the board). Connectivity – 10/100/1000 Mbps Ethernet USB – 1x mini USB 2.0 device port, 1x USB 2.0 host post Camera – 2x 30-pin camera interface Debugging – 1x debug serial port, […]