kickstarter News - Page 12 of 49 - CNX Software

March 14, 2022March 14, 2022 by Jean-Luc Aufranc (CNXSoft) - 10 Comments

DingDian S3 – A Pocket-sized Intel Pentium N6000 mini PC (Crowdfunding)

DingDian S3 is an ultra-compact, pocket-sized mini PC powered by an Intel Pentium Silver N6000 Jasper Lake processor, and equipped with 16GB RAM, and up to 1TB SSD with two M.2 sockets for either SATA or NVMe storage. The mini PC also includes a 2.5GbE port, an Intel AX201 WiFi 6 and Bluetooth 5.2 M.2 module, a 4K-capable HDMI 2.0 port, four USB ports, and a 3.5mm audio jack. DingDian S3 specifications: SoC – Intel Pentium Silver N6000 quad-core Jasper Lake processor @ 1.10 GHz / 3.3 GHz (Turbo) with Intel UHD graphics 605; 6.5W TDP System Memory – 16GB LPDDR4 Storage – 128GB SATA SSD, 512GB or 1TB NVMe SSD Video Output 1x HDMI 2.0 port up to 4Kp60 1x DisplayPort Alt Mode via USB-C port up to 4Kp60 Audio – 3.5 audio jack, digital audio via HDMI Networking 2.5GbE via Intel i225 controller Dual-band 802.11b/g/n/ax WiFi 6 and […]

February 27, 2022February 27, 2022 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

Beagle-Pi Emulator is a Raspberry Pi HAT adapter for BeagleBone Black (Crowdfunding)

Beagle-Pi Emulator BeagleBone Black Industrial

We recently reported the Raspberry Pi boards were getting really expensive due to a lack of supply, and the problem has gone on for while without a clear idea when the issue will be resolved. This does not help Raspberry Pi HAT manufacturers, and for instance, Sequent Microsystems has made Raspberry Pi HATs over the years most models with multiple relays, but also others for temperature sensors, and others automation applications. One solution would be to use compatible boards like ODROID-C4 or Rock64, but Sequent Microsystems found out the BeagleBone Black Industrial was well-stocked by various distributors, and instead, they designed the “Beagle-Pi Emulator” adapter to use Raspberry Pi HAT on the Texas Instruments Sitara AM3358 board. An adapter is needed because the BeagleBone Black boards are equipped with two 46-pin headers instead of the 40-pin header on Raspberry Pi SBC’s. The expansion board routes I2C, SPI, four serial […]

February 22, 2022 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Creality CR-Scan Lizard 3D scanner works on black objects, offers up to 0.05 mm accuracy (Crowdfunding)

When we first looked at 3D scanners a few years ago, products that provided decent results were fairly expensive. But at the end of last year, we covered the Revopoint POP 2 color 3D scanner that appears to offer good scans at a relatively affordable (~$420) price point. Creality, more known for its 3D printers, has now introduced the CR-Scan Lizard 3D scanner with a similar or even lower pricing point, an accuracy of up to 0.05mm, support for scanning of dark/black objects, as well as an optional color kit to scan objects with full colors. Creality CR-Scan Lizard specifications: Accuracy – Up to 0.05 mm Single capture range/area – 200 x 100 mm Point distance – 0.1 to 0.2 mm Working distance – 150 to 400 mm Minimum scan volume – 15 x 15 x 15 mm Scan speed – Up to 10 fps Light source – LED + […]

February 3, 2022 by Jean-Luc Aufranc (CNXSoft) - No Comments

Foldable, portable laser cutter & engraver comes with built-in fume filtration (Crowdfunding)

Optic foldable portable laser cutter & engraver

If you’d wish you could easily carry your laser engraver or cutter around, conveniently store it after use due to the limited space in your office, or/and dreamt of a built-in fume filtration system into your machine, Rendyr’s Optic may be what you are looking for. It is a foldable, portable laser cutter & engraver that still provides a large 18-inch x 12.2-inch work area (around 457 x 310mm), and also includes a built-in fume filtration system with replaceable multi-stage filter cartridges. Optic key features and specifications: Laser Dual-diode laser module with active cooling 15W output power (20W under test) Manual focus adjustment with 3-stage precision height gauge Focal Length: fixed, 0.78” (20mm) Beam Size: 10-100 microns Filtration system with easily exchangeable filters Optional exhaust module to replace the filter and using a shop vacuum to vent outside Work area Foldable 457 x 310mm cutting mat with an alignment grid […]

January 25, 2022January 25, 2022 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

StackyPi – A Raspberry Pi RP2040 board with Raspberry Pi Zero form factor (Crowdfunding)

SB Components’ StackyPi is a development board based on Raspberry Pi RP2040 MCU that happens to follow the Raspberry Pi Zero form factor. The board is equipped with 8MB SPI flash for the firmware, a MicroSD card socket, a micro SB port, two buttons, and a 40-pin GPIO header that makes it compatible with some Raspberry Pi uHAT and HAT expansion boards. StackyPi specifications: MCU – Raspberry Pi RP2040 dual-core Cortex-M0+ microcontroller @ up to 133 MHz with 264KB SRAM Storage – 8MB (64Mbit) SPI flash, MicroSD card socket USB – 1x Micro USB port Expansion – 40-pin GPIO header with GPIO, I2C, UART, SPI, etc… mostly compatible with Raspberry Pi header (3.3V I/Os) Misc – Reset and Boot buttons Power Supply- 5V via Micro USB port Dimensions – 65 x 30 mm (Raspberry Pi Zero form factor) The main advantage of such as board is that it can support […]

December 29, 2021 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Raspberry Pi UPS HAT takes two 18650 batteries (Crowdfunding)

Raspberry Pi UPS solutions have been available for years with products like PiJuice Zero, PiVoyager, or LiFePO4wered/Pi+. But the team at SB Components has designed another UPS HAT for Raspberry Pi with a holder for two 18650 batteries. The HAT is designed for 5V operation up to 2.5A, connects with the Raspberry Pi SBC through the I2C bus from the 40-pin GPIO header, and is equipped with a 0.91-inch OLED for information display. UPS HAT for Raspberry Pi specifications: Power Input – 8.4V/2A via DC jack Power Output – 5V up to 2.5A through LDO chip (GPIO header and 2x USB ports) Display – 0.91-inch OLED Host interface – I2C Misc – On/Off switch Battery support 18650 Lithium battery (not included) via holder for two batteries Battery reverse indicator Charging and voltage monitoring via TI INA219 I2C chip Battery voltage balancing with Hycon HY2213 Battery protection IC (Hycon HY2120) Dimensions […]

December 23, 2021December 23, 2021 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

HUENIT modular robot arm takes 3D printer, laser engraver, suction, AI camera modules (Crowdfunding)

Most robot arms are designed to carry and manipulate payloads, but HUENIT modular robot arm is much more versatile as besides a traditional suction module, the robot supports modules such as a 3D printer, laser engraver, pen holder for drawings, and a creator module for let people designed their own. The robot arm can hold payloads of up to 750 grams, have a reach of up to 39 cm without module, supports WiFi and Bluetooth connectivity, and can also optionally be fitted with a 2MP AI camera module based on Kendryte K210 RISC-V processor with built-in AI accelerators. HUENIT specifications: Robot arm 4-axis Payload up to 750 grams Reach – 390mm without module Repeatability – 0.05mm Precision – 0.1mm Speed – Up to 500mm/s Storage – MicroSD card slot USB – 1x USB-C port Wireless – WiFI and Bluetooth Misc – UART, external stepper Power Supply – 24V DC input, […]

December 8, 2021December 24, 2021 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

LoRa expansion boards work with Raspberry Pi SBC and Raspberry Pi Pico board (Crowdfunding)

We’ve covered a number of LoRa solutions based on Raspberry Pi boards, and SB Components is now offering another with the LoRa HAT for Raspberry Pi equipped with an Ebyte E22 LoRa module operating in either the 433 MHz, or 868 and 915 MHz bands. The company also offers a LoRa expansion for Pico based on the same E22 module, adding a small 1.14-inch LCD for information display, and designed for the Raspberry Pi Pico board with the RP2040 dual-core Cortex-M0+ microcontroller. LoRa HAT for Raspberry Pi specifications: LoRa connectivity LoRa Module (one or the other) Ebyte E22-900T22S based on SX1262, operating in the 850 MHz to 930 MHz band Ebyte E22-400T22S based on SX1268, operating in the 410 MHz to 493MHz band Supported frequencies – 433 MHz, 868 MHz, 915 MHz Range – Up to 5 km line-of-sight Antenna – SMA antenna connector USB – 1x Micro USB port […]