oled News - Page 2 of 3 - CNX Software

October 13, 2017 by Jean-Luc Aufranc (CNXSoft) - 25 Comments

This TTGO Board Combines ESP32, LoRa Radio, and OLED Display for just $10

Just one year ago, it would cost around $15 to $20+ to get an ESP32 board, that is if you were lucky/fast enough to order one one before it went out of stock. Since then, availability is no longer an issue, and you now can get an ESP32 development board for as low as about $7, or even around $4 during promotions. Today, I was made aware of another board sold under the “TTGO” brand, that includes not only ESP32 WiFi and Bluetooth SoC, but also a (433 MHz) LoRa radio, and an OLED display. Price? Just $10 plus shipping ($1.75 here). TTGO ESP32/LoRa board specifications: WiSoC – Espressif ESP32 Storage – 32MB on-board flash (or maybe just 16MB?) LoRa Semtech SX1278 with u.FL connector + 433MHz antenna (N.B.: Antenna must be connected during use or the Semtech chip could be damaged) Sensitivity” ~ -148dBm; output power: +20dBm Display – […]

June 25, 2017June 25, 2017 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

MXCHIP AZ3166 IoT Developer Kit is Designed to Work with Microsoft Azure

MXCHIP is a Shanghai based company designing and manufacturing WiFi IoT modules such as EMW3165, which has now made a development board based on their EMW3166 STM32+ Cypress module – called MXChip AZ3166 – specifically designed for Microsoft Azure cloud computing platform. MXChip AZ3166 board specifications: Wireless Module – EMW3166 WiFi module with STM32F412 ARM Cortex M4F MCU @ 100 MHz with 256KB SRAM，1MB+2MB SPI Flash, Cypress BCM43362 WiFi chip Display – 128×64 OLED display Audio – Audio codec, built-in microphone, and 3.5mm heaphone jack Sensors – Motion sensor, magnetometer, atmospheric pressure sensor, temperature and humidity sensor Expansion – Finger extension interface with 25 external I/O pins including GPIOs, I2C, I2S, UART, ADC, Reset, 3.3V, and GND Debugging – DAP Link emulator USB – 1x Micro USB port for power, programming, debugging Misc – 2x user buttons; 1x RGB light; 3x working status indicator; IR emitter; Security encryption chip Power Supply […]

May 28, 2017May 29, 2017 by Jean-Luc Aufranc (CNXSoft) - 10 Comments

FriendlyELEC Mailbag: NanoPi NEO OLED Starter Kit, NEO Station NS-120B, and NanoPi K2 Multimedia Kit

FriendlyELEC will send me some review samples from time to time, and normally I just ask for one item, but they aways send a bunch of their products instead. This time I asked for a NanoPi NEO NAS Kit v1.2 to play with, but I got clearly more than what I asked for… Let’s start with the box at the top. It contains “NanoPi NEO complete starter kit” selling for $29.99for $29.00 with the following items: NanoPi NEO board NanoHat OLED Heatsink and thermal pad kit Akuminum housing a Mico USB cable A micro SD card pre-loaded with NEO OLED Ubuntu firmware. Three buttons, and screws It’s actually not fully complete, as you’d need to provide and solder your own male headers to NanoPi NEO board. I did not have time for soldering that day, but the final results should be really neat based on pictures from their website. If […]

May 21, 2017May 22, 2017 by Jean-Luc Aufranc (CNXSoft) - 10 Comments

Using GPIOs on NanoPi NEO 2 Board with BakeBit Starter Kit

NanoPi NEO 2 is a tiny 64-bit ARM development board powered by Allwinner H5 processor. FriendlyELEC sent me a couple of NEO 2 samples together with their BakeBit Start Kit with a NanoHat and various modules via GPIOs, analog input or I2C. I’ve already tested both Armbian with Linux 4.11 and Ubuntu Core Qt with Linux 3.10, and ran a few benchmarks on NanoPi NEO 2. You would normally prefer to use the Armbian image with Linux mainline since it provided better performance, but at the time I was told GPIO support was not there. Configuring NanoPi NEO 2 board with BakeBit library So this week-end, when I decided to test GPIO support and BakeBit Starter Kit, I decided to follow this advice, especially nanopi-neo2-ubuntu-core-qte-sd4g-20170329.img.zip image is still the recommended one in the Wiki. So I went with that image. I’ll use Python examples from Bakebit library, but if you […]

September 9, 2016September 9, 2016 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

ArduBoy Arduino Compatible Portable Game Console Sells for $39

Ardubox feels like the little brother of PocketCHIP portable & hackable game console with its transparent case, but instead of running Linux on a 32-bit ARM processor, Ardubox is based on the same Atmel ATmega32u4 MCU used in Arduino Leonardo & Micro boards. Arduboy specifications: MCU – Atmel ATmega32u4 AVR MCU with 32KB flash, 2.5KB RAM, and 1KB EEPROM Display – 128×64 1-bit OLED display USB – 1x micro USB 2.0 port for power and programming User Inputs – 6x momentary tactile buttons Audio – 2 channel Piezo Speaker Misc – 1x LED Battery – 180 mAh Thin-Film Li-Po battery good for over 8 hours Beside the Arduino IDE, The board can also be programmed with Codebender, GCC & AVRDude. There’s also a fairly long list of games to play with, and it can be hacked as a virtual business card, a USB mouse and keyboard, a synthesizer, and more. […]

June 2, 2016June 7, 2016 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Xiaomi Mi Band 2 Fitness Tracker Adds an OLED Display, Promises 20-day Battery Life

I’m not a big fan of fitness trackers without display that require you to monitor your daily progress on your smartphone, and that’s probably why when Xiaomi released their first fitness band I was not quite as interested, but now the Chinese company has released Mi Band 2 with an OLED display, an heart rate monitor, IP67 ingress protection rating, and a 20-day of battery life for just 149 RMB ($23). Mi Band 2 key features: Fitness, heart rate and sleep tracker OLED display, view time, step count, heart rate 20-day battery, IP67 water resistant ADI accelerometer and optical heart rate sensor Anodized 0.05mm ultra-thin button Upgraded pedometer algorithm Hypoallergenic silicone band 2nd gen Bluetooth 4.0 for faster, stable connections It’s still good to be able to gather your fitness data over time, and you can do so with Mi Fit app for Android or iOS. The downside with an […]

April 7, 2016 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

BPI-GSM Arduino Compatible Board Integrates a GSM & GPS Module, Sensors and an OLED Display

Banana Pi team has come up with another board, but this time it does not run Linux or Android, as they’ve made an Arduino compatible board called BPI-GSM based on Atmel ATmega2560 MCU with a light sensor, DHT22 temperature and humidity sensor, and a GSM/GRPS & GPS module powered by a LiPo battery. BPI-GSM board specifications: MCU – Atmel ATmega2560 8-bit AVR MCU @ 16 MHz with 256 KB flash, 8KB SRAM, 4KB EEPROM Connectivity – Simcom SIM808 GSM, GPRS, and GPS module + SIM card slot + Sensors – DHT22 temperature and humidity sensor, light sensor Display – OLED display Expansion headers – 54x digital I/O (including 14x PWM), 16x analog input, 4x UART. Max DC current per I/O: 40 mA. Misc – Reset button, LEDs Power Supply 5V via micro USB port 3.7V LiPo battery (2,500 mAh battery included in kit) Dimensions – TBD The board can be […]

October 7, 2014October 7, 2014 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

$25 TinyScreen is an OLED Display for TinyDuino Arduino Compatible Board (Crowdfunding)

Back in 2012, Tiny Circuits launched a Kickstarter campaign for TinyDuino, an Arduino compatible board that’s… tiny, based on Atmel Atmega328P, and supports tiny stackable shields in a similar fashion to Microduino (launched in 2013). The campaign was successful, and the company is now back on Kickstarter with TinyScreen, an OLED display that can be stacked on top of TinyDuino to create a smartwatch, a minuscule gamepad, smart glasses, and more. TinyScreen technical specifications: 96×64 OLED display, 16-bit color depth 0.96″ (24.4mm) viewable area Software controllable backlight (OLED brightness) Power down mode Four push buttons along the sides (connected to IO pins) SPI interface for display Power Supply – 3.0V to 5.5V operation (higher voltages supported with TinyShield power regulator) Power Consumption – 20 – 45mA max supply current (depending on brightness) Dimensions – 25.8mm x 25.0mm Programming of TinyDuino can be done through a web interface for Arduino called […]