14-Inch 4K IPS Bar Touch Display
Posted on

14-Inch 4K ultra-wide touch display is optimized for Raspberry Pi and LattePanda boards, features USB Type-C and HDMI interfaces

DFRobot’s 14-inch ultra-wide IPS display offers narrow bezels, 4K (3840 x 1100) resolution, 10-point capacitive touch, and is designed for mounting single board computers such as LattePanda Sigma and Raspberry Pi 5. It can also be connected to other computers with dual USB Type-C and mini HDMI video input interfaces. With a unique 3.5:1 bar-shaped aspect ratio, this display can present information in an intuitive format for countertop advertising screens, measurement equipment, and smart terminals. DFRobot’s “14-inch 4K IPS bar touch display” specifications Display 14-inch ultra-wide, narrow bezel IPS bar touch display with 4K (3840×1100) resolution Ten-point capacitive touch support, offering precise input Aspect ratio – 3.5:1 Pixel – 0.08964(H) × 0.08964(V) mm Viewable area – 344.2(H)×98.6(V) mm with 170° viewing angle and ≥6H surface hardness Color Gamut – 72% Brightness – 300 cd/m2 Contrast Ratio – 1200:1 Refresh rate – 60Hz Transmittance – Greater than equals to 86% Driver […]

Flexible Raspberry Pi Pico
Posted on

RP2040 FlexiBoard is a bendable Raspberry Pi Pico clone made of flexible PCB (Crowdfunding)

[Update December 22: The project was previously called FlexiPi, but Raspberry Pi considered it infringed on its trademarks, so the name was changed to RP2040 FlexiBoard instead]. RP2040 FlexiBoard is a bendable Raspberry Pi RP2040 board made of flexible PCB with the same layout as the original Raspberry Pi Pico, but featuring a USB-C port instead of a micro USB port on the official board. This follows the Flexduino flex PCB clone of the Arduino UNO made by “EDISON SCIENCE CORNER”, but the smaller design of “TOP Gadgets” RP2040 FlexiBoard may make it potentially more useful since it could be inserted into tight or round enclosures. RP2040 FlexiBoard specifications: MCU – Raspberry Pi RP2040 dual-core Cortex-M0+ microcontroller @ 48 MHz (overclockable to 133 MHz) with 264KB SRAM Storage – 2MB QSPI flash USB – 1x USB Type-C 1.1 port used for power and programming Expansion 2x 20-pin 2.54mm pitch header […]

ArmSoM RK3588 AIModule7 NVIDIA Jetson Nano-compatible SOM
WEBS-21J0-ASL Nano-ITX embedded system
Posted on

Portwell WEBS-21J0-ASL – A rugged embedded system with Intel Atom x7000RE Nano-ITX motherboard and Hailo-8 AI accelerator

Portwell’s WEBS-21J0-ASL is a fanless, rugged embedded system with a Nano-ITX motherboard powered by an Intel Atom x7000RE Series processor and optimized for industrial IoT applications. It features two 2.5Gbps Ethernet ports, dual 4K display support (DP/HDMI), and a serial port as well as M.2 E and B Key sockets for wireless and storage expansion. Designed for harsh environments, the WEBS-21J0-ASL operates in temperatures ranging from -20°C to 60°C. The system is equipped with DDR4 SO-DIMM memory (up to 16GB and 10Gbps USB 3.2 Gen 2 ports. It has passed vibration and shock tests for durability in rugged applications making it suitable for a wide range of industrial and automation systems. The WEBS-21J0-ASL also supports optional integration with the Hailo-8 AI acceleration module delivering up to 26 TOPS of AI performance for applications requiring advanced AI capabilities. This makes it an ideal solution for robotics, medical equipment, outdoor gateways, and […]

Jetson Orin NX AI Development Kit
Posted on

NVIDIA Jetson Orin NX development kit comes with up to 16GB RAM, 128GB NVMe SSD, WiFi 5

Waveshare’s Jetson Orin NX Development Kit is an AI edge computing platform tailored for robotics and AI-driven applications built around the NVIDIA Jetson Orin NX module 8GB/16GB delivering up to 70 TOPS and 100 TOPS of AI performance, respectively. It features the JETSON-ORIN-IO-BASE base board, which provides essential interfaces like an M.2 socket, DisplayPort (DP) video output, and USB ports, making it easy for users to connect multiple sensors and peripherals for high-performance AI tasks. The kit includes a 128GB NVMe SSD for high-speed storage and comes pre-installed with the AW-CB375NF wireless network card, which supports dual-band Wi-Fi 5 and Bluetooth 5.0. The Jetson Orin NX module operates within a configurable power range of 10W to 25W, delivering up to 5x the performance of the Jetson Xavier NX module. This development kit is suitable for large-scale AI projects requiring multiple concurrent inference pipelines and high-speed data processing. Previously, we covered […]

Raspberry Pi AI HAT+ 26 TOPS
Posted on

Raspberry Pi AI HAT+ features Hailo-8L or Hailo-8 AI accelerator with up to 26 TOPS of performance

The Raspberry Pi AI HAT+ is a PCIe expansion board for the Raspberry Pi 5 with either a 13 TOPS Hailo-8L or 26 TOPS Hailo-8 AI accelerator. You may remember the Raspberry Pi AI Kit was introduced last June with an official M.2 Key M HAT+ and a 13 TOPS Hailo-8L M.2 AI accelerator module, The new Raspberry Pi AI HAT+ is quite similar except the chip is soldered on the expansion board and offered with either Hailo-8L or the more powerful Hailo-8 variant. Raspberry Pi AI HAT+ specifications: Supported SBC – Raspberry Pi 5 AI accelerator Hailo-8L AI accelerator with up to 13 TOPS of performance Hailo-8 AI accelerator with up to 26 TOPS of performance Host Interface – PCIe Gen3 interface 16mm stacking GPIO header PCIe FPC cable Spacers and screws enabling fitting on Raspberry Pi 5 with Raspberry Pi Active Cooler Dimensions – 65 x 56.5 mm […]

ESP32-S3 Touch AMOLED 1.91
Posted on

ESP32-S3 board features 1.91-inch AMOLED display and QMI8658 6-axis motion sensor

Waveshare has launched an ESP32-S3 1.91-inch AMOLED development board with a 6-axis motion sensor designed for the rapid prototyping of IoT and portable projects with interactive displays. The board is built around the ESP32-S3R8 chip, featuring a 32-bit LX7 dual-core processor running at up to 240MHz, with integrated 2.4GHz Wi-Fi and Bluetooth BLE 5. It also includes 16MB Flash, 8MB PSRAM, 512KB SRAM, and 384KB ROM for efficient processing and memory management. At the core of its display capabilities is a 1.91-inch AMOLED screen with a 240×536 resolution, supporting 16.7 million colors. Powered by the RM67162 controller and connected via the QSPI interface, the display is ideal for running GUI applications like LVGL. The board is available in both touch and non-touch versions, with the touch-enabled models using the FT3168 touch IC. Other features include a QMI8658 6-axis IMU, a microSD card slot, and a Lithium battery header. The ESP32-S3 […]

Rockchip RK3568, RK3588 and Intel x86 SBCs and SoMs in 2025
Pico DALI2 Expansion Module
Posted on

DALI2 expansion module for ESP32-C6-Pico and ESP32-S3-Pico boards facilitates Smart Lighting integration

Waveshare has recently launched the Pico-DALI2 expansion module for ESP32-Pico series boards designed to enable DALI communication for customized control of multiple lighting groups. It is compatible with development boards such as the ESP32-C6-Pico and ESP32-S3-Pico and includes a DALI communication screw terminal for connecting external DALI devices. DALI (Digital Addressable Lighting Interface) is a standardized protocol used for lighting control in building automation systems. The latest version of the DALI2 protocol is better than the old one in that it offers enhanced interoperability, additional features like multi-master configurations, and better energy management capabilities. DALI2 devices can communicate bidirectionally, meaning controllers can send commands and also receive status feedback from lighting devices, allowing for more complex automation and diagnostics. We can get more information about DALI from Wikipedia. We have previously seen the uses of DALI in Texas Instruments MSPM0 Arm Cortex-M0+ microcontrollers as an interface and in Acme CM3-Home […]

Cocket Nova CH552 dev board
Posted on

$6 Cocket Nova CH552 development board features CH552G 8-bit MCU with an enhanced 8051 core

The Cocket Nova CH552 is a cheap and versatile development board built around the CH552G MCU with an enhanced 8051 core clocked at 24MHz. Designed for beginners and hobbyists, this board features easy USB Type-C programming, onboard LEDs and a Neopixel RGB, reset and boot buttons, and Qwiic/STEMMA QT connectors for easy expansion. Additionally, it gives access to 17 GPIOs, PWM, ADC, and touch button capabilities. These features along with low-cost and standard breadboard compatibility make this development board suitable for learning and experimentation. We have previously written about other products built around the CH552G/T microcontroller, namely a $10 Arduino-programmable keyboard and the Turing Smart Screen 3.5-inch USB Type-C information display. Users interested in inexpensive 8-bit MCU boards may also check out Electrodragon’s CH551 mini development board based on another MCU part of the CH55x family. Cocket Nova CH552 development board specifications: MCU – WCH CH552 8-bit Enhanced USB single-chip MCU […]

Boardcon CM3588 Rockchip RK3588 System-on-Module designed for AI and IoT applications