OpenWrt Category - Page 14 of 37 - CNX Software

September 6, 2021 by Jean-Luc Aufranc (CNXSoft) - 28 Comments

OpenWrt 21.02 released with WPA3, HTTPS, TLS enabled by default

OpenWrt 21.02 has just been released with higher security with WPA3, HTTPS & TLS enabled by default, as well as initial support for the Distributed Switch Architecture (DSA), the Linux standard for configurable Ethernet switches. OpenWrt is the most popular open-source Linux distribution for routers and entry-level Linux-capable embedded systems, and the latest release includes over 5800 commits since the release of OpenWrt 19.07 in January 2020. WPA3 was already supported in OpenWrt 19.07, but not enabled by default, OpenWrt 20.02 changes that, together with TLS thanks to trusted CA certificates from Mozilla. That means LuCi interface, wget, opkg package manager can all support HTTPS out-of-the-box. Note that HTTPS redirection can be disabled for LuCI in the configuration files. Another security change is that SELinux is now supported by OpenWrt, but not enabled by default. OpenWrt 21.02’s DSA implementation replaces the current swconfig system, but not all targets have been […]

September 1, 2021May 6, 2022 by Jean-Luc Aufranc (CNXSoft) - 12 Comments

Allwinner V833 AI video development board runs Tina Linux or Melis RTOS

Allwinner V833 AI camera development board

Lindenis V833 is an AI video/camera development board based on Allwinner V833 single-core Cortex-A7 processor with a 400 MOPS AI accelerator (NPU) and running OpenWrt-based Tina Linux or Melis RTOS based on the RT-Thread kernel. The board comes with up to 3GB RAM, a MicroSD card socket, MIPI DSI, MIPI CSI, and BT1120 interfaces for video output and input, Gigabit Ethernet, 2.4 GHz WiFi, and a few other I/Os. Lindenis V833 specifications: SoC – Allwinner V833 single-core Arm Cortex-A7 processor @ up to 1.2 GHz with H.265/H.265 1080p video encoder, MJPEG 1080p video encoder, 400 MOPS AI accelerator (See PDF datasheet) System Memory – Up to 3GB DDR3/DDR3L Storage – MicroSD card slot with support for SDHC and SDXC, SPI NOR flash Display Interfaces 4-lane MIPI-DSI up to 1080p BT1120 output Touch panel header Video In 4-lane MIPI-CSI camera interface BT1120 input Audio – 3.5mm Line-in jack, built-in microphone Connectivity […]

August 23, 2021 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Qualcomm IPQ4019 802.11ac Wave 2 WiFi system-on-module comes with Dual Gigabit Ethernet baseboard

Wallys Communication has introduced their lowest cost networking platform with the DR4019S board equipped with two Gigabit Ethernet ports, as well as a Qualcomm IPQ4019 802.11ac Wave 2 WiFi system-on-module. The module comes with 32MB NOR flash, and 256MB DDR memory and targets applications ranging from security surveillance to commercial radio coverage to hotel wireless applications, or even forest fire protection engineering. DR4019S board specifications: SoC – Qualcomm IPQ4019 quad-core Arm Cortex A7 at 716.8 MHz System Memory – 256MB DDR Storage – 32MB NOR flash Connectivity 2x Gigabit Ethernet ports 802.11b/g/n/ac Wave 2 WiFi 5 with 2x 5G MMCX connectors, 2x 2.4G MMCX connectors (but we can only see one or two of those on the provided photo) USB – 1x USB 3./2.0 port Misc – Debug UART header Power Supply – 12V via DC jack Power Consumption – 9.6W (max) Dimensions – 65 x 35 x 16mm Temperature […]

July 14, 2021July 14, 2021 by Jean-Luc Aufranc (CNXSoft) - 15 Comments

MAIX-II A AI camera board combines Allwinner R329 smart audio processor with USB-C camera

Earlier this year, we wrote about Sipeed MAIX-II Dock AIoT vision devkit with an Allwinner V831 camera processor with a small 200 MOPS NPU, an Omnivision SP2305 2MP camera sensor, and a 1.3-inch display. But for some reason, which could be supply issues, Sipeed has designed a much different variant called MAIX-II A with a board based on Allwinner R329 smart audio processor, a 720p30 USB camera module, and a 1.5-inch display. MAIX-II A board specifications: Main M.2 module – Maix-II A module with Allwinner R329 dual-core Cortex-A53 processor @ 1.5 GHz, 256MB DDR3 on-chip, a dual-core HIFI4 DSP @ 400 MHz, and Arm China AIPU AI accelerator for up to 256 MOPS, plus Wi-Fi & BLE and a footprint for an SPI Flash. Storage – MicroSD card socket Display – 1.5-inch LCD display with 240×240 resolution Audio – Dual microphones, 3W speakers Camera – 720p USB-C camera module based […]

June 14, 2021June 14, 2021 by Jean-Luc Aufranc (CNXSoft) - 13 Comments

HaneSOM is a 4 cm2 Arm Linux module powered by Microchip SAMA5D2 SiP

DAB Embedded HaneSOM is a tiny (4 cm2) system-on-module based on Microchip SAMA5D2 Arm Cortex-A5 processor running Linux, which could make it the world’s smallest Linux module. The small size is made possible by the use of a SAMA5D2 system-in-package that also integrates 128MB DDR2, and the only two other chips on the modules are a 4MB flash (GD25Q32) and the PMIC (MIC2800). HaneSOM specifications: SiP – Microchip ATSAMA5D27C-D1G system-in-package with SAMA5D27 Arm Cortex-A5 processor @ 500 MHz with NEON, 128MBytes DDR2 System Memory – 128MBytes DDR2 memory Storage – 4 MBytes of QSPI Flash Castellated holes giving access to signal for: Storage – SD card interface Display – 24-bit RGB LCD TFT interface; capacitive touch controller Camera – Up to 5MP CMOS camera sensor support Audio – SSC, I2S Networking – 10/100M Ethernet USB – USB 2.0 (OTG and host) SPI, I2C, UART, CAN-FD, 12-bit ADC, PWM Misc – […]

June 10, 2021 by Jean-Luc Aufranc (CNXSoft) - 17 Comments

ClearFog CN9130 networking boards deliver 10GbE through a tiny Octeon TX2 module

SolidRun has designed and manufactured ClearFog networking boards ever since the introduction of the Marvell ARMADA 380/388-based ClearFog Pro in 2015. Since then, more powerful models have been launched including the ClearFog GT 8K based on Marvell ARMADA A8040 quad-core Cortex A72 processor with support for 2.5GbE and 10GbE, and the ClearFog CX LX2K equipped with a 16-core Cortex-A72 NXP capable of 100GbE networking. The Israeli company unveiled its first Octeon TX2-based design last fall with ClearFog CX CN9K, a full-featured networking SBC fitted with CEx7 CN9132 COM Express Type 7 module. But now the company has launched the more compact ClearFog CN9130 Pro/Base networking boards equipped with a tiny 50x30mm Octeon TX2 module still enabling 10GbE connectivity. SolidRun SOM 9130 system-on-module Specifications: SoC – Marvell OCTEON TX2 CN9130 quad-core Cortex A72 processor @ up to 2.2 GHz (commercial) or 2.0 GHz (industrial) System Memory – Up to 8GB DDR4 […]

May 20, 2021May 21, 2021 by Jean-Luc Aufranc (CNXSoft) - 49 Comments

Nezha RISC-V Linux SBC launched for $99 and up

Last month, we wrote about Allwinner D1 SBC & processor that promised to offer a relatively low-cost RISC-V Linux solution. We were not given a name at the time, but there was a logo of Nezha, a fictional character from Chinese literature. The board is now known as the Nezha SBC and has been launched on Indiegogo for $99 and up as a board designed for IoT projects running Linux, but can also be purchased directly on Aliexpress for the same price. [Update: It can also be purchased on Taobao for 599 RMB] Nezha SBC specifications: SoC – Allwinner D1 single-core XuanTie C906 64-bit RISC-V processor @ 1.0 GHz with HiFi4 DSP, G2D 2D graphics accelerators Memory – 1GB DDR3 memory Storage – 256MB SPI NAND flash, MicroSD card slot Video Output – HDMI 1.4 port up to 4Kp30, MIPI DSI & touch panel interface up to 1080p60 Decoding – […]

May 2, 2021May 10, 2021 by Jean-Luc Aufranc (CNXSoft) - 19 Comments

Allwinner D1 RISC-V processor SDK & Documentation

We published information about Allwinner D1 SBC and processor a few weeks ago. The news was pretty interesting as it’s the first RISC-V processor from the company, and one of the first affordable RISC-V SBC. But all we had at the time was hardware information from a leak, or rather from China-only Allwinner developer website. But now the company has added more information to its open-source development website with the release of documentation, now only in Chinese, as well as the Allwinner D1 Tina SDK. Eventually, there should be a better SDK via linux-sunxi community and some are already working on the Allwinner D1 SBC, but let’s try to get the SDK from Allwinner and build the code from source using the documentation. First, you’d need to register on Allwinner open-source website and click on signup. You’ll probably want to select Email registration. Now fill your username, select a country, […]