Processors Category - Page 628 of 1077 - CNX Software

May 22, 2017May 23, 2017 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

Qualcomm Snapdragon 845 Octa-core Processor To Feature ARM Cortex A75 Cores (Reports)

According to reports from China, Qualcomm’s next application processor (or rather mobile platform) will be Snapdragon 845, and if accurate, the comparison table below between the Snapdragon processor and Hisilicon Kirin 970 SoC shows the former will be powered by some customized (魔改) version of yet-to-be announced ARM Cortex 75 cores. Snapdragon 845 octa-core processor will be manufactured using Samsung 10nm LPE processor, come with four custom Cortex A75 cores, four Cortex A53 cores, an Adreno 630 GPU, and an LTE X20 modem supporting LTE Cat 18 for up to 1.2 Gbps download speed. Other features like 802.11ad (High bandwidth, short range WiFi), UFS 2.1, and LPDDR4X were already found on earlier model. I’ve been unable to find further details about ARM Cortex A75 right now, and we have to wait until ARM Techcon 2017 before getting more details. Mobile phones powered by Snapdragon 845 are supposed to start shipping […]

May 22, 2017May 22, 2017 by Jean-Luc Aufranc (CNXSoft) - No Comments

$399 Intel Euclid Robotics Devkit Runs Ubuntu & ROS on Intel Atom x7-Z8700 Processor

We’ve seen many mini PC based on Intel Atom x5/x7 “Cherry Trail” processor in the last year, but Intel has also integrated their low power processor into hardware aimed at robotics, such as Intel RealSense development kit based on Atom x5 UP Board and RealSense R200 depth camera. The company has now launched its one-in-all Intel Euclid development kit combining Atom X7-Z8700 processor with a RealSense camera in a single enclosure. Intel Euclid specifications: SoC – Intel Atom x7-Z8700 Cherry Trail quad core processor @ up to 2.4GHz with Intel HD Graphics Gen 8 System Memory – 4GB LPDDR3-1600 Storage – 32GB eMMC 5.0 flash, Micro SD slot up to 128GB Video Output – micro HDMI port up to 4K @ 30 Hz Audio – 2x I2S interfaces, 1W mono speaker, 3x DMIC with noise cancellation Camera – Intel RealSense ZR300 camera RGB camera – 2MP up to 1080p@30fps, 16:9 […]

May 22, 2017May 22, 2017 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Foxconn Bandott STB is an Amlogic S905D TV Box with Dual HDMI Input, Netflix 4K Support

So far, we’ve seen two dual tuner set-top boxes powered by Amlogic S905D processor with Sen5 Android STB and Mecool KI Pro, but earlier this year, Foxconn launched Bandott set-top box based on the processor, with any tuner, but two HDMI inputs, and Widevine L1 and PlayReady 3.0 support allowing for 4K video playback for premium services like Netflix (see Bandott page), CatchPlay, iqiyi, and myVideo. BANDOTT BA101 specifications: SoC – Amlogic S905D quad core ARM Cortex-A53 processor @ 1.5 GHz with penta core Mali-450MP GPU System Memory – 2GB RAM Storage – 8GB flash Video Output – 1x HDMI 2.0b (HDCP) Video Input – 2x HDMI 1.4 Audio Output – HDMI, and 3.5mm headphone jack Connectivity – 10/100M Ethernet, dual band Wi-Fi 802.11ac/b/g/n (2×2), Bluetooth 4.0 USB – 1 x USB 2.0 DRM – Widevine L1 and PlayReady 3.0 The box runs Android TV 6.0, and was unveiled in […]

May 22, 2017May 22, 2017 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Arduino Cinque Combines SiFive RISC-V Freedom E310 MCU with ESP32 WiFi & Bluetooth SoC

SiFive introduced the first Arduino compatible board based on RISC-V processor late last year with HiFive1 development board powered by Freedom E310 MCU, but the company has been working with Arduino directly on Arduino Cinque board equipped with SiFive Freedom E310 processor, ESP32 for WiFi and Bluetooth, and an STM32 ARM MCU to handle programming. Few other technical details have been provided for the new board, but since it looks so similar to HiFive1, I’ve come with up with preliminary/tentative Arduino Cinque specifications: MCU – SiFive Freedom E310 (FE310) 32-bit RV32IMAC processor @ up to 320+ MHz (1.61 DMIPS/MHz) WiSoC – Espressif ESP32 for WiFi and Bluetooth 4.2 LE Storage – 32-Mbit SPI flash I/Os 19x Digital I/O Pins 19x external interrupt pins 1x external wakeup pin 9x PWM pins 1/3 SPI Controllers/HW CS Pins I/O Voltages – 3.3V or 5V supported USB – 1x micro USB port for power, […]

May 21, 2017May 22, 2017 by Jean-Luc Aufranc (CNXSoft) - 10 Comments

Using GPIOs on NanoPi NEO 2 Board with BakeBit Starter Kit

NanoPi NEO 2 is a tiny 64-bit ARM development board powered by Allwinner H5 processor. FriendlyELEC sent me a couple of NEO 2 samples together with their BakeBit Start Kit with a NanoHat and various modules via GPIOs, analog input or I2C. I’ve already tested both Armbian with Linux 4.11 and Ubuntu Core Qt with Linux 3.10, and ran a few benchmarks on NanoPi NEO 2. You would normally prefer to use the Armbian image with Linux mainline since it provided better performance, but at the time I was told GPIO support was not there. Configuring NanoPi NEO 2 board with BakeBit library So this week-end, when I decided to test GPIO support and BakeBit Starter Kit, I decided to follow this advice, especially nanopi-neo2-ubuntu-core-qte-sd4g-20170329.img.zip image is still the recommended one in the Wiki. So I went with that image. I’ll use Python examples from Bakebit library, but if you […]

May 19, 2017June 14, 2017 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

HiMedia Q30 TV Box is Powered by HiSilicon Hi3798M V200 Processor

HiSilicon Hi3798M V200 processor is a cost-down version of Hi3798C V200 processor with a cheaper Mali-450MP GPU, a single Gigabit Ethernet MAC, a single USB 3.0 port shared with SATA and PCIe interface. One of the first devices with the processor will be Himedia Q30 TV box based on Himedia Q3 design. HiMedia Q30 specifications: SoC – HiSilicon Hi3798M V200 quad-core ARM Cortex A53 processor with an ARM Mali-450MP GPU supporting OpenGL ES2.0/1.1, OpenVG1.1, EGL, and System Memory – 2 GB DDR3 Storage – 8 GB eMMC flash, SD card slot Video Output – 1x HDMI 2.0a up to 4K @ 60 Hz, 1x composite video (RCA); Imprex 2.0 PQ engine with support for HDR/HLG/SLF/HDR to SDR, BT.709, and BT.2020 Audio Output – HDMI, stereo audio (RCA), optical S/PDIF port Video Engine – HiVXE 2.0 with support for HEVC 10-bit 4Kx2K @ 60 fps, H.264 4K2K @ 30 fps Connectivity […]

May 19, 2017 by Jean-Luc Aufranc (CNXSoft) - 14 Comments

Sen5 Amlogic S905D TV Box Review – Part 2: Android Firmware, Kodi 17, and DVB-T2 & S2 App

Sen5 is one of the first Android TV boxes powered by Amlogic S905D processor, and comes with two tuners (DVB-C/T/T2 and DVB-T/T2) with two demodulators that should allow for recording on one tuner, while watching the other, or recording two channels at the same time. We’ve already check out the hardware in the first part of the review, and seen a glimpse of the neat user interface, so today I’ll report about my experience with the device. Sen5 Android Set-Top Box First Boot, Setup Wizard, & First Impressions The STB comes with two USB ports so I used one for the hard drive, a necessity if you plan to use the PVR function, and connected a USB hub to the other with RF dongles for an air mouse and a gamepad, as well as a USB keyboard to take screenshots. I also connected Ethernet and HDMI cables, as well as […]

May 18, 2017May 18, 2017 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

Android Things Developer Preview 4 Released with Google Assistant SDK Support

Earlier this month, Google released a preview of the Google Assistant SDK that works on boards running Debian like the Raspberry Pi 3, and even launched AIY Project Voice Kit for the later. You can now play with Google Assistant on Android Things as the company has just released Android Things Developer Preview 4 with support for Google Assistant SDK. The operating systems works on any Android Things certified devices, but the example instructions for Google Assistant API on Android Things also include steps to use Raspberry Pi 3 board together with AIY Projects Voice kit. The developer preview 4 also adds I2S to the peripheral I/O API and is demonstrated in the aforementioned example, and new hardware support with NXP i.MX7D based Pico Board equipped WiFi & Bluetooth, Ethernet, USB ports, an audio jack, and an I/O expansion port. Android Things DP4 also brings the ability for developers to […]