Video Category - Page 203 of 331 - CNX Software

August 24, 2016November 2, 2016 by Jean-Luc Aufranc (CNXSoft) - 45 Comments

M12N Amlogic S912 Octa-core TV Box Review – Part 2: Android 6.0 Firmware

Shenzhen Shiningworth MXQ Plus M12N is one of the first TV box powered by Amlogic S912 octa-core processor also bringing a faster GPU, VP9 and HDR support compared to the earlier Amlogic S905 processor. I’ve already shown the device, its accesories, and its internal degisn in the first part of MXQ Plus M12N review, so today I’ll spend time reporting my finding testing features and performance with Android 6.0 firmware. Setup Wizard and First Impressions Since there are only two USB ports, I connected my USB hard drive to one, and used a USB hub to connect input devices including two RF dongles for an air mouse, and a gamepad, as well as a USB keyboard to take screenshots. I also added Ethernet and HDMI cable, and finally connected the power supply to boot it up. But as you can see from the picture the very first boot was not […]

August 24, 2016August 27, 2016 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

ReSpeaker WiFi IoT Board is Designed for Voice Interaction (Crowdfunding)

More and more devices are supporting voice interaction nowadays from your smartphone to devices like Amazon Echo, but so far, I had not seen development boards specifically designed for that purpose, and that’s exactly what Seeed Studio ReSpeaker board does by combining audio capabilities, WiFi connectivity, and I/O headers. ReSpeaker Core board specifications: WiFi Module – Acsip AI7688 Wi-Fi 802.11 b/g/n module based on Mediatek MT7688 MIPS SoC Storage – micro SD card slot USB – 1x micro USB port for programming and power Audio – 3.5mm AUX port, WM8960 audio codec, 2-pin header for external speakers Expansion – 2x 8-pin expansion headers for I2C, GPIO and USB 2.0 host connected to MT7688, built-in microphone. MCU – Atmel ATMega32U4 @ 16 MHz Misc – 12x RGB LEDs, 8x touch sensors, 3 push buttons Power Supply – 5V DC Dimensions – 70mm diameter Weight – 70 grams The board runs OpenWrt, […]

August 22, 2016 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Learn the Basics of Humanoid Robots with InMoov Finger Starter Kit

In a not so distant future, most humans will live off their government provided basic income, relaxing and drinking their robot brewed, drone delivered beer or soda, opened and served by their humanoid robot maid. Well, maybe… In the meantime, it might be interesting to learn how to make humanoid robots such as InMoov, but since it’s quite complicated, it might be better to start small… with a single finger. That’s exactly what InMoov Finger Starter Kit offers you to do in order to understand the basics principles of the complete robot. The kit includes: 1x 3D printed base support in ABS 3D printed finger parts in ABS 1 meter braided 200 LB tendon 1x 5cm filament for peg/pin use to assemble finger joints 1x wheel horn adapter (Servo Pulley) 4x screws to fix the servo to the base support. You’ll also need to provide your own Arduino Uno (or […]

August 21, 2016August 22, 2016 by Jean-Luc Aufranc (CNXSoft) - 12 Comments

Using M12N Android Amlogic S912 TV Box as a Game Console (Video)

When Amlogic announced S912 processor, they mentioned it would target not only 4K OTT and IP set-top boxes, but also gaming consoles thanks to a faster and better Mali-T820MP3 GPU compared to the Mali-450MP GPU found in their previous S905 and S805 processor, and we’ve already seen that S912 is indeed faster in 3D benchmarks. So I decided to play several games to show the performance, the pre-loaded retro gaming app, and for people who have never used a TV box to play games show what it looks like, and how to play using M12N TV box, in conjunction with MINIX NEO A2 Lite air mouse and Tronsmart Mars G01 wireless gamepad. I played four games downloaded from the Play Store or Amazon Underground: Candy Crush Saga with air mouse Beach Buggy Racing and Riptide GP2 with the gamepad Dead Trigger with the air mouse in menus, and the gamepad […]

August 16, 2016August 16, 2016 by Jean-Luc Aufranc (CNXSoft) - 11 Comments

How-to Setup a DLNA/UPnP Server in Linux for Smoother Video Streaming with Kodi and Other Media Players

I’m normally playing videos from a SAMBA share installed in a Ubuntu PC to play files from Kodi in Android TV box reviews, but sometimes when I use 10/100 Ethernet, or worse WiFi local “streaming” may not be as smooth as possible. SAMBA is convenient because of access control and read write operations, but if you want to get a bit more performance, you may switch to NFS instead, or like I’ve going to show you here to a DLNA / UPnP server to stream videos locally from Kodi 16.1. There are several options, but MiniDLNA is lightweight compared to MediaTomb, so it will also run on lower end hardware like cheap ARM Linux development boards like Raspberry Pi, Orange Pi, or NanoPi NEO without taking too many resources. Installation is very easy in Debian / Ubuntu distributions, and I supposed this should also work with Windows Subsystem for Linux […]

August 15, 2016August 16, 2016 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

4K VP9, H.265 and H.264 Video Playback in Amlogic S912 M12N TV Box

I’ve received my first Amlogic S912 TV box with MXQ Plus M12N TV box this week-end, and I’ve decided to start testing by showing the media capabilities of the platform that is supposed to support 4K VP9 up to 60Hz, 4K 10-bit H.265 up to 60Hz and 4K H.264 up to 30 Hz. I connected the device to Onkyo TX-NR636 A/V recevier itself connected to LG 42UB820T 4K UHD TV, set video output to 2160p @ 60Hz, and played several 4K video samples from a USB hard drive using the pre-installed version of Kodi 16.1: 4K Hawaii Sunset _ GoPro Hero 4 Black 4k@30fps-I7CycuMpQ3w.webm (Downloaded from YouTube) – OK Beauty_3840x2160_120fps_420_8bit_HEVC_MP4.mp4 (H.265 @ 30 fps – No audio) – OK big_buck_bunny_4k_H264_30fps.mp4 (H.264 @ 30 fps – MPEG1/2 and AC3 audio) – OK big_buck_bunny_4k_H264_60fps.mp4 (H.264 @ 60 fps – MPEG1/2 and AC3 audio) – Video a bit choppy, large audio delay. Expected […]

August 13, 2016November 2, 2016 by Jean-Luc Aufranc (CNXSoft) - 12 Comments

MXQ Plus M12N (Amlogic S912) TV Box Review – Part 1: Specs, Unboxing, and Teardown

Shenzhen Shiningworth has just sent me the first Amlogic S912 Android TV box for review with their MXQ Plus M12N model. The first part of the review will focus on specifications, accessories, and hardware design, and in the second part I’ll connect and boot the device to make a thorough review of the firmware. MXQ Plus M12N Specifications The specifications are pretty standard and comparable to the ones of yet to launch Amlogic S912 TV boxes: SoC – Amlogic S912 octa-core ARM Cortex A53 processor @ up to 2.0GHz with ARM Mali-820MP3 @ up to 750MHz System Memory – 2GB DDR3 Storage – 16GB eMMC flash and SD slot up to 32GB Video Output – HDMI 2.0a up to 4K @ 60Hz with CEC and HDR support, and AV port (composite) Audio Output – HDMI, AV (stereo audio), and optical S/PDIF Connectivity – Fast Ethernet, dual band WiFi 802.11 b/g/n/ac, […]

August 12, 2016 by Jean-Luc Aufranc (CNXSoft) - No Comments

Evive is an Arduino Compatible Platform with Enclosure, Lots of I/Os, Buttons, and an 1.8″ Display (Crowdfunding)

Engineers at Agilo Technologies, an Indian startup based in Kanpur, Uttar Pradesh, felt that the wire mess often produced while learning or prototyping with Arduino boards could be an issue, and it was easy to mis-wire your setup, so they’ve decided to create a user and student friendly Arduino compatible system with many of the items you’d normally use with Arduino board such as buttons, probes inputs, an 1.8″ color display, headers for ESP8266, Bluetooth, and XBEE moduels, etc.. and all of that enclosed in a neat case. Evive was born. Evive specifications: MCU – Atmel ATmega2560 8-bit AVR MCU @ 16 MHz with 256KB flash, 4KB EEPROM, 8KB SRAM Storage – micro SD slot up to 32GB Display – 1.8″ TFT display; 160×128 resolution; 18-bit color User inputs – Tactile and slide switches, joysticks, and potentiometers Probes inputs – Voltage / Intensity sensing inputs USB – USB device port Expansion Headers […]