802.15.4

Posted on by Jean-Luc Aufranc (CNXSoft) - 14 Comments on ESP32 UWB board features DW1000 module for accurate indoor positioning

ESP32 UWB board features DW1000 module for accurate indoor positioning

ESP32 UWB board

FiRa “Fine Ranging” UWB technology was introduced a few years ago and is now found in devkits and Apple U1 chip. Makerfabs ESP32 UWB board provides another option with Espressif ESP32-WROVER-32 or ESP32-WROOM-32 WiFi & Bluetooth module combined with a Decawave DW1000 module for precision tracking. Makerfabs explains the board acts like a continuously scanning radar that locks onto another device (called Anchor, since it’s usually in a fixed location) and communicates with it to determine the distance between objects by calculating the time of flight (ToF) between devices, or in other words, the roundtrip time of challenge/response packets. ESP32 UWB board specifications: Wireless modules: WiFi & Bluetooth LE – ESP32-WROVER-32 or ESP32-WROOM-32 module with ESP32 dual-core processor @ 240 MHz UWB – B&T BU01 module based on Decawave DW1000 chip; IEEE802.15.4-2011 UWB compliant wireless transceiver module with a precision of 10cm indoors, a data rate of up to 6.8 […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 9 Comments on ESP32-H2 Bluetooth LE & 802.15.4 RISC-V SoC shows up in ESP-IDF source code

ESP32-H2 Bluetooth LE & 802.15.4 RISC-V SoC shows up in ESP-IDF source code

ESP32-H2

Espressif Systems is working on yet another RISC-V chip with ESP32-H2 SoC offering Bluetooth LE and 802.15.4 connectivity showing up in the ESP-IDF framework source code. A code comparison shows ESP32-H2 is very similar to ESP32-C3 with a single RISC-V core, albeit clocked at up to 96 MHz, and the first Espressif SoC without WiFi, as the WiFi radio is replaced with an 802.15.4 radio for Thread, Zigbee, etc… that can be used for the development of Home Automation, Smart Lighting, and wireless sensor network applications. While looking at the source code differences between ESP32-C3 and ESP32-H2, the really only major differences were the 802.15.4 radio and lower maximum frequency, and at the current time, it looks like most of the rest is unchanged, so it’s possible they kept the same amount of RAM (400KB), storage, and most of the same peripherals, but it could just well be the code […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on MKR SharkyPro BLE, Zigbee, OpenThread development board follows Arduino MKR form factor

MKR SharkyPro BLE, Zigbee, OpenThread development board follows Arduino MKR form factor

MKR SharkyPro I STM32WB55 board

Just a few days ago, we mentioned STMicro launched STM32WB5MMG wireless module to simplify Bluetooth LE, Zigbee, OpenThread connectivity by allowing 2-layer baseboards for the module. It turns out there’s also such a module from a third-party with namely Midatronics SharkyPro module based on STM32WB55, and the company also launched MKR SharkyPro I & II development boards following Arduino MKR form factor. MKR SharkyPro specifications: Wireless Module – SharkyPro module Wireless MCU – STMicro STM32WB55CG/CE dual-core Arm Cortex-M4 core at 64 MHz (application processor) and Arm Cortex-M0+ core at 32 MHz (network processor) with 512KB flash, 256KB SRAM Connectivity – Bluetooth 5.0 LE, Bluetooth Mesh 1.0, OpenThread, Zigbee, and other IEEE 802.15.4 proprietary protocols Antenna – Onboard chip antenna (SharkyPro I) or SMA antenna  connector (SharkyPro I) Power 3.3V supply voltage Consumption  – 13 nA in shutdown mode, 600 nA in Standby mode + RTC + 32 KB RAM Dimensions […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 1 Comment on STM32WB Feather board features STM32WB55 Bluetooth 5.0 SoC

STM32WB Feather board features STM32WB55 Bluetooth 5.0 SoC

STM32WB Feather Board

STMicro announced the availability of their first wireless STM32 MCU last year with STM32WB55 Bluetooth 5.0 and 802.15.4 Cortex-M4/M0+ microcontroller together with P-NUCLEO-WB55 Development Pack. A company called Reclaimer Labs has now designed a Feather-compatible board with the wireless MCU, more specifically STM32WBCGU6, and simply called STM32WB Feather board. STM32WB Feather Board specifications: Wireless MCU – STMicro STM32WB55CG Bluetooth SoC with Arm Cortex-M4 application core, Arm Cortex-M0+ Bluetooth co-processor, 1 MB Flash storage, 256 KB of SRAM, USB ROM Bootloader Storage – 128 Mbit SPI NOR Flash memory Bluetooth antennas – On-board chip antenna, u.Fl connector for external antenna Expansion – 16-pin + 12-pin unpopulated headers with 6x analog input pins UART, I2C, SPI, and 7x GPIO pins Debugging – Standard SWD debug connector Misc – User button and LED, 32.768 kHz crystal for LSE/RTC Power Supply 5V via micro USB port 2-pin battery header, LiPo battery charger Dimensions – […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on Nordic Semi nRF21540 RF front end module Extends the Range of nRF52/nRF53 Bluetooth SoC’s

Nordic Semi nRF21540 RF front end module Extends the Range of nRF52/nRF53 Bluetooth SoC’s

A little while ago, we wrote about RFCat N32 board integrating Meshtek-H52 module with nRF52832 2.4GHz multi-protocol SoC and a Skyworks power amplifier increasing power by up to 30 times to extend the wireless range to up to 200 meters. It turns out Nordic Semi outed its own range extender module late last year with nRF21540 RF front end module (FEM) that integrates a power amplifier (PA) and low noise amplifier (LNA) optimized to boost the link budget of the nRF52 and nRF53 multi-protocol wireless SoCs. nRF21540 key features and specifications: Supported wireless standards Bluetooth Low Energy (incl. Bluetooth mesh) Thread and Zigbee (802.15.4) Proprietary 2.4 GHz Output Power – Adjustable in small increments up to +21 dBm Receive Gain – +13 dB with 2.5 dB noise figure Antennas – 2x antenna ports for antenna diversity Host Interface – I/Os, SPI, or a combination Supply Voltage – 1.7 V to […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 3 Comments on IoTSDR Linux Board Targets the Development of IoT Gateways with Standard or Custom IoT Protocols (Crowdfunding)

IoTSDR Linux Board Targets the Development of IoT Gateways with Standard or Custom IoT Protocols (Crowdfunding)

iotSDR board

Xilinx Zynq-7010/-7020 powered iotSDR board by EmbedINN enables the development of IoT gateways with support for LoRa, SigFox, WeightLess, Bluetooth, BLE, 802.15.4, ZigBee, as well as custom IoT protocols. The board also supports GPS, Galileo, Beidou, and GLONASS navigation systems thanks to a Maxim Integrated MAX2769 GNSS chip. iotSDR key hardware features and specifications: SoC (one or the other) Xilinx Zynq-Z7010 (XC7Z010-1CLG400C) dual-core Arm Cortex-A9 processor with 256 kb on-chip memory, FPGA fabric with 28,000 logic cells, 17,600 LUTs, 2.1 Mb block RAM, 80 DSP slices Xilinx Zynq-Z7020 (XC7Z020-1CLG400C) dual-core ARM Cortex-A9 processor with 256 kb on-chip memory, FPGA fabric with 85,000 logic cells, 53,200 LUTs, 4.9 Mb block RAM, 220 DSP slices System Memory – 512 MB DDR3 Storage 128 Mbit QSPI flash memory for firmware Microchip AT24MAC602 SPI EEPROM for RF transceiver MCU firmware and data Radios “IoT” Radios RF Transceivers – 2x Microchip/Atmel AT86RF215 European band – […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on Nordic nRF52820 Bluetooth 5.2 SoC Supports Thread, Zigbee and Full Speed USB 2.0

Nordic nRF52820 Bluetooth 5.2 SoC Supports Thread, Zigbee and Full Speed USB 2.0

nRF52820 Block Diagram

Nordic Semi has launched the sixth multi-protocol SoC part of their nRF52 family with nRF52820 Bluetooth 5.2 ultra low power System-on-Chip (SoC) supporting  Bluetooth Low Energy (Bluetooth LE), Bluetooth mesh, as well as Thread, Zigbee, and 2.4-GHz proprietary. nRF52820 can handle all Bluetooth 5/5.1/5.2 versions with features such as Long Range, 2 Mbps throughput, direction finding, LE power control, and LE isochronous channels. The SoC also happens to include a Full Speed (12 Mbps) USB 2.0 interface. nRF52820 key features and specifications: MCU Core – Arm Cortex-M4 @ 64 MHz Memory – 32 KB RAM Storage – 256 KB Flash Wireless Connectivity Bluetooth 2 Mbps, 1 Mbps, Long Range Bluetooth Low Energy Bluetooth Direction Finding Bluetooth mesh Thread, Zigbee 802.15.4/ANT/2.4 GHz proprietary Up to +8 dBm TX power Security – 128-bit AES encryption USB – Full Speed USB 2.0 Other Peripherals UART, 2x SPI/TWI, QDEC Analog comparator 4x 32-bit timer/counter, […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 14 Comments on Electrolama to Launch 802.15.4/Zigbee USB Dongle and Raspberry Pi “HAT”

Electrolama to Launch 802.15.4/Zigbee USB Dongle and Raspberry Pi “HAT”

zig-a-zig-ah

Electrolama (@omerk and friends) has been working on two open-source hardware 802.15.4/Zigbee projects with “zig-a-zig-ah” (aka “zzh”) USB stick based on Texas Instruments CC2652R SimpleLink multi-standard wireless MCU and Zoe (Zigbee + Poe) development board based on Raspberry Pi HAT form factor and powered by TI CC2530 SimpleLink 2.4 GHz SoC alongside CC2592 range extender. Both boards are released under an Apache-based Solderpad Hardware License 2.0, and target users of the Zigbee2MQTT project.  The boards could soon also get native support in Home Assistant via the “zigpy-cc” library which adds support in ZHA (Zigbee Home Automation) integration component. Zig-a-zig-ah USB Stick Preliminary specifications: WiSoC – Texas Instruments CC2652R SimpleLink multi-standard wireless MCU with support for Thread, Zigbee, Bluetooth 5 Low Energy, IEEE 802.15.4g, 6LoWPAN, and proprietary systems. (Note: CC2652RB is also considered as it does not require an external crystal oscillator) Host Interface – USB via CH340 USB-UART bridge Misc […]

Exit mobile version