automation

Posted on by Jean-Luc Aufranc (CNXSoft) - 3 Comments on Z-Pi 7 Z-Wave gateway devkit works with Raspberry Pi and Orange Pi Zero boards

Z-Pi 7 Z-Wave gateway devkit works with Raspberry Pi and Orange Pi Zero boards

Z-Wave Raspberry Pi & Orange Pi Zero

WiFi & Bluetooth are the most popular wireless protocols for home automation, alternatives like Zigbee and Z-wave have also been widely adopted, at least in some countries. And if you are interested in the latter, Aeotec has just introduced the Z-Pi 7  gateway development kit that lets you add Z-Wave connectivity to Raspberry Pi boards or Orange Pi Zero SBC with an expansion board connected over UART through the GPIO header. Aeotec Z-Pi 7 Z-Wave expansion board (ZWA025) specifications: Z-Wave connectivity Silicon Labs EFR32ZG14 Arm Cortex-M4 SoC @ 39 MHz with Series 700 and Gen7 technology  Frequencies ZWA025-A: US Frequency 908.42 Mhz ZWA025-B: AU Frequency 921.42 Mhz ZWA025-C: EU frequency  868.42 Mhz TX Power – US: +9.3 dBm; EU: +4.8 dBm RX sensitivity – -97.5 dBm Range Indoor – US: 70+ meters; EU: up to 60 meters Outdoor – Up to 200 meters SmartStart native integration and S2 security. Z-Wave Plus Certified […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 2 Comments on Ebyte E104-BT11 Bluetooth Mesh module features Silicon Labs EFR32MG21 MCU

Ebyte E104-BT11 Bluetooth Mesh module features Silicon Labs EFR32MG21 MCU

Ebyte E104-BT11 Bluetooth Mesh modules

Ebyte E104-BT11 is a Bluetooth Mesh module offered in four variants with support for gateways (G) and node (N) versions, as well as PCB or IPEX antenna versions. Interestingly it is based on Silicon Labs EFR32MG21 Cortex-M33 microcontroller also found in ITEAD Zigbee 3.0 USB dongle, so it’s not impossible that it could be repurposed for Zigbee or Thread with firmware from Silabs. Ebyte E104-BT11 module specifications: Wireless MCU – Silicon Labs EFR32MG21 Arm Cortex-M33 microcontroller @ up to 80 MHz with DSP and FPU, up to 1024 kB flash, up to 96 kB RAM, 2.4 GHz IEEE 802.15.4 for Bluetooth LE, Zigbee, or Thread Wireless connectivity Bluetooth Mesh/BLE support with default firmware, up to 10,922 devices supported Max Tx power – 20 dBm Rx sensitivity- -88 to -97 dBm (-97 dBm typ.) Max data rate – 1Mbps Antenna – PCB antenna up to 200-meter range, or IPX antenna up […]

Posted on by Sponsored Post - Comments Off on ANYbotics’ ANYmal C robot is a multi-module machine (Sponsored)

ANYbotics’ ANYmal C robot is a multi-module machine (Sponsored)

anymal c legged robot ml industrial inspection action

Rugged four-legged robot with three brains ANYbotics provides solutions for robot applications with the most advanced mobility and autonomy requirements in challenging terrains. The massive embedded computing performance for the key tasks – situational awareness, motion control and mission fulfillment – is delivered by three COM Express Computer-on-Modules from congatec. Due to the advancements in computer-based intelligence and sensor technology, previously stationary robots unaware of their environment are now evolving into smart autonomous mobile robots. This will not only help to relieve humans of potentially dangerous tasks but also to optimize repetitive tasks in real-life environments from an economic point of view. Such robots can autonomously fulfill many jobs that previously required human labor and significantly extend the list of feasible tasks. With such a perspective, it is not surprising that robot applications are a booming market. The overall global smart robot market is expected to grow with a CAGR […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 3 Comments on MYS-8MMX i.MX 8M Mini SBC runs Yocto 3.0 Linux or Ubuntu 18.04

MYS-8MMX i.MX 8M Mini SBC runs Yocto 3.0 Linux or Ubuntu 18.04

i.MX 8M Mini SBC

MYiR Tech has just launched MYS-8MMX single board computer powered by NXP i.MX 8M Mini Cortex-A53/Cortex-A4 processor with 2GB RAM, 8GB eMMC flash, and designed for embedded applications in areas of consumer electronics, industrial automation, smart healthcare, security monitoring, etc… thanks to its video and graphics capabilities. MYS-8MMX SBC specifications: SoC  – NXP i.MX 8M Mini Quad quad-core Cortex-A53 processor @ 1.6 GHz (industrial temp.) or 1.8 GHz (commercial temp.), Arm Cortex-M4F realt-time core @ 400 MHz, Vivante 2D and 3D GPU’s, and 1080p VPU System Memory – 2GB DDR4 (supports up to 4GB) Storage – 8GB eMMC flash (supports up to 128GB), 32MB QSPI flash, MicroSD card slot, M.2 NVMe SSD support Video Output 40-pin FPC connector for LVDS & capacitive touchscreen interface 1x HDMI output up to 1080p60 Camera I/F – 24-pin FPC connector with MIPI-CSI Connectivity Gigabit Ethernet RJ45 port 2.4GHz/5GHz dual-band WiFi 5 and Bluetooth 5.0 […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on LoRaWAN BACnet gateway uses Raspberry Pi CM3+ for building automation

LoRaWAN BACnet gateway uses Raspberry Pi CM3+ for building automation

Raspberry Pi BACNet Gateway with LoRaWAN

A few years about we wrote about BASpi I/O Raspberry Pi HAT compatible with BACNet, a data communication protocol for Building Automation and Control Networks, also known as the ISO 16484-6  standard, and used for HVACs, lightings, elevators, fire safety, and other systems found in buildings. But if you’d like a turnkey BACnet solution based on Raspberry Pi, UK-based Innovelec‘s DINGO LoRaWAN BACnet Advanced Gateway/Server may be easier to integrate into your building’s electrical installation and also offers low-power long-range LoRaWAN communication. DINGO-LORAWAN-GW_SVR-01 key features and specifications: System-on-Module – Raspberry Pi Compute Module 3+ with Broadcom BCM2837B0 quad-c ore Arm Cortex-A53 processor @ 1.2GHz, 1GB LPDDR2 RAM, 8GB eMMC Flash (16GB  or 32 GB as option), RTC Info Display – 128×64 pixel OLED LCD Video Output – HDMI Networking 1x RJ45 10/100BaseT Ethernet 1x RJ45 10BaseT Ethernet LoRaWAN connectivity Support for LoRaWAN V1.0.2 and V1.0.3 Tx Power – Up to […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 1 Comment on ClearLink EtherNet/IP motion and I/O controller supports 4 axes of motion control

ClearLink EtherNet/IP motion and I/O controller supports 4 axes of motion control

Clearlink EtherNet/IP Controller

A few weeks ago, we wrote about ClearCore Arduino compatible industrial I/O and motion controller that can be programmed with the Arduino IDE or a C/C++ SDK. Teknic has now announced ClearLink with basically the same hardware, but instead of being programmable in C++, the controller is managed over the EtherNet/IP protocol. ClearLink key features and specifications: MCU – Microchip SAME53 Arm Cortex-M4F microcontroller clocked at up to 120 MHz, with 512 KB flash, 192 KB of SRAM Storage – MicroSD card slot Connectivity 1x 10/100M Fast Ethernet RJ45 port compatible with EtherNet/IP Support for Xbee modules for wireless communication (WiFi, Bluetooth, ZigBee, DigiMesh, 802.15.4, etc.) I/Os 2x RJ45 serial ports for SPI or UART devices (5V output) 13x 3-pin terminal blocks with software configurable I/O, power, and ground Digital outputs can drive resistive or inductive loads up to 9 watts such as contactors, pneumatic or liquid valves, guard locks, […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 1 Comment on Ryzen Embedded V2000 COM Express Module supports up to 1TB NVMe SSD, 64GB DDR4

Ryzen Embedded V2000 COM Express Module supports up to 1TB NVMe SSD, 64GB DDR4

Kontron COMe-BV26

We’ve already covered some COM Express modules based on AMD Ryzen Embedded V2000 processors with products like ADLINK cExpress-AR COM Express Type 6 Compact computer-on-module, but Kontron COMe-bV26 is the first we’ve seen that follow COM Express Basic Type 6 standard. The module supports up to 64GB DDR4 via two SO-DIMM connectors, up to 1TB NVMe onboard SSD, exposes 8x PCIe lanes, and with an 8-core/16-thread Ryzen Embedded V2000 processor is well-suited to IoT edge devices that must perform parallel processing tasks. Kontron COMe-bV26 specifications: AMD Embedded V2000 SoC AMD V2748 octa-core/16-thread processor @ 2.9 GHz / 4.15 GHz (Turbo) with 4MB L2 cache, 7CUs Radeon RX Vega 7 GPU @ 1.6 GHz; TDP: 35-54W AMD V2718 octa-core/16-thread processor @ 1.7 GHz / 4.15 GHz (Turbo) with 4MB L2 cache, 7CUs Radeon RX Vega 7 GPU @ 1.6 GHz; TDP: 10-25W AMD V2546 hexa-core/12-thread processor @ 3.0 GHz / 3.95 […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 16 Comments on Pack of 4 ESP8266 smart plugs sold for $13.49 (Promo)

Pack of 4 ESP8266 smart plugs sold for $13.49 (Promo)

ESP8266 smart plug pack discount

There’s currently a promotion on Amazon for a pack of four ESP8266 smart plugs that are ETL and FCC certified, and sold for $13.49, or around $3.5 per socket. In order to apply for the discount, you’ll need to the Amazon product page, tick on “Save an extra 20% when you apply this coupon.”, and enter the coupon code “ABVYP87G“. Once this is all done the price will be $13.49 shipped within the US. The plug works in the 100-240V range, but when shipping outside of the US, you’ll need to pay extra for shipping and provisions for customs duties. Gosund WP3 key features: 2.4 GHz WIFI connectivity Rated Voltage: 100 – 240V Rated Current: 10A Max AC Frequency: 50/60Hz Max power: 1100W Operating Temperature – -10 ~ 60°C If you have no interested in running proprietary software, you’ll be happy to know Gosund WP3 smart plugs are compatible with […]