ble News - Page 39 of 54 - CNX Software

January 9, 2018October 21, 2021 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

SKIIN Smart Underwears Support Energous’ WattUp Near, Mid, and Far-Field Wireless Charging

Near-field wireless charging has been around for several years, but for wireless charging to become really disruptive it needs to work at a distance, and Energous has been working on mid and far-field technology with their WattUp transmissive to charge devices respectively on the desk (mid-field) or in the room (far-field). You need to have compatible devices to work with the technology, and wearables are a prime target, but I was expecting fitness trackers or smartwatches to embed the technology at first, but instead one of the first WattUp compatible wearables are smart underwears from SKIIN. The module found in SKIIN underwears and bras have many of the same features as your typical fitness tracker and some extras: Sensors ECG sensors for Heart Rate Monitoring (HRM) Accelerometer and Gyroscope to measure motion & posture BIA (Bioelectrical impedance analysis) to monitor water intake levels and how your sweat affects your hydration, […]

December 28, 2017December 28, 2017 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Garmin Launches Vivofit 4 Activity Tracker with One Year Battery Life

I have not spent much time covering wearables like smartwatches and fitness trackers this year, mostly because I find they have too many flaws at this stage. Back in 2016, I found many had a short life time, they would just stop working after a few weeks or months, even the fairly popular Xiaomi Mi Band 2 only lasted 2 months after an ill-fated firmware upgrade. In my case, I also found activity / fitness trackers did not have the motivating factor I thought they’d have, so I don’t think I exercise more or less with one. Finally, another annoyance is that most need to be charged every couple of days or weeks, and I’m frequently leaving the one I’m still using (SH09) run out of battery, losing recent data. The best solution to address the latter issue would be some type of energy harvesting, so that we would never […]

December 21, 2017December 21, 2017 by Jean-Luc Aufranc (CNXSoft) - No Comments

Obniz ESP32 Board is Programmable in JavaScript from the Cloud (Crowdfunding)

ESP32 WiFi / Bluetooth boards are now commonly supported by the Arduino IDE, and alternative firmwares are also available to program them using JavaScript (e.g. Espruino), or MicroPython. But if are familiar with JavaScript / Node.js, and don’t want to flash your own firmware, Obniz board could be an option. The board exposes 12 I/Os programmable from the company’s Cloud service, and features a OLED display used to show your program information, or a QR code to easily program the board from your smartphone’s browse once a WiFi connection has been setup. Obniz hardware specifications: Wireless Module – ESP-WROOM-ESP32 based on ESP32 dual core 802.11 b/n/g WiFi + Bluetooth LE WiSoC Display – 128×64 OLED display I/Os 12x I/O pins each configurable as GPIO, ADC, UART, SPI or I2C (no specialized pin, each can handle those functions) Up to 1A drive per I/O to control motors 3.3 or 5V selectable […]

December 9, 2017 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

RAK Wireless Introduces LoRa + BLE Module, LoRa GPS Tracker, and NB-IoT/eMTC Arduino Shield

We’ve previously covered several products from RAK Wireless, including RAK WisCam Arduino compatible Linux camera, RAK CREATOR Pro Ameba RTL8711AM WiFi IoT board, and WisCore modular development kit for application leveraging voice assistants such as Amazon Alexa. AFAIK, the company had not released any new products since their RAK831 LoRa gateway module launched last summer, but they just contact me with the release of three new wireless products, namely RAK813 BLE + LoRa module, RAK811 LoRa tracker board, and WisLTE NB-IoT/eMTC/eGPRS Arduino shield. RAK813 BLE + LoRa module & Development Board Main features and specifications: Connectivity LoraWAN via Semtech SX127x (LoRa) chipset Frequency Ranges 433MHz, 470MHz FCC Frequency range 902~928MHz CE Frequency range 863~870MHz MIC Frequency range 920~928MHz KCC Frequency range 920~923MHz Receiver Sensitivity: LoRa down to -146 dBm TX Power – adjustable up to +14 dBm, max PA boost up to 20dbm Range – Up to 15 km in rural […]

December 7, 2017December 7, 2017 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

ESP32-PICO-KIT v4 Board Based on ESP32-PICO-D4 SiP Now Available for $10

A little while ago, I received a bunch of ESP32 PICO Core development boards which were based on Espressif Systems ESP32-PICO-D4 system-in-package with ESP32, 4MB SPI Flash, and other components. The advantage of such chip is that is requires less external component, and allows for smaller designs. For example, the boards I received would leave two row of pin on each side of the board, while most other ESP32 boards will only expose one row on each side. I used the board to play with Micropython ESP32 port, and later-on when I launched a giveaway of 8 of the boards, I found out the name had changed to ESP32-PICO Kit, with the documentation listing v3 with all pins connected to male headers, and v4 with 6-pin not connected to a male header as shown in the photo below. Both versions of the board also have a different pin layout. But […]

December 2, 2017 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

Amazon FreeRTOS Released for NXP, Texas Instruments, STMicro, and (soon) Microchip Microcontrollers

FreeRTOS is an open source real-time operating system for microcontrollers released under an MIT license, and when it comes to adoption in embedded systems it’s right there near the top with embedded Linux according to Aspencore 2017 embedded markets study. For example, some Espressif SDKs for ESP8266 or ESP32 are based on FreeRTOS, and so is Mediatek LinkIt Development Platform for RTOS. The recently announced Amazon FreeRTOS (a:FreeRTOS) leverages the open source operating systems, and extends it with with libraries that enable local and AWS cloud connectivity, security, and soon over-the-air updates. a:FreeRTOS is free of charge, open source, and available today. In order to get started, you’ll have a choice of 4 hardware platforms: STMicro STM32L4 Discovery Kit IoT Node (B-L475E-IOT01A) powered by STM32L475 ARM Cortex-M4 MCU with 802.11 b/g/n WiFi, Bluetooth 4.1 LE, RF (868 / 915 MHz), and NFC connectivity, plenty of sensors NXP LPC54018 IoT module (OM40007) […]

November 18, 2017 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

HackaBLE Board is a Tiny, Breadboard-Friendly Bluetooth LE Development Board

Earlier this year, I wrote about Electronut Labs’ Bluey development board powered by Nordic Semi nRF52832 development board with BLE, NFC, and a few sensors, and partially open source hardware with the KiCAD schematics and PCB layout available on Github. The company is now back with another open source hardware nRF52832 BLE board, namely hackaBLE, that’s much smaller (28x18mm), and with 2.54mm pitch castellated pin headers making suitable for use for breadboard, or as a module on a custom designed board. hackaBLE board specifications: SoC – Nordic Semi nRF52832 ANT + BLE ARM Cortex-M4 @ 64 MHz processor with 512kB flash, 64kB RAM Connectivity – Bluetooth 4.2/5 LE and other proprietary 2.4 GHz wireless standards via chip antenna Expansion 2x 9-pin castellated headers with GPIO, 5V, 3.3V, and GND 2x 5-pin solder pads for more I/Os Debugging – 4-pin SWD header Misc – RGB LED, and user button Power Supply […]

November 1, 2017November 9, 2017 by Jean-Luc Aufranc (CNXSoft) - 240 Comments

Giveaway Week – ESP32 PICO Kit v3 Boards

I don’t have one, but eight boards to give away to four winners (2 each) with Espressif Systems ESP32 PICO Kit v3 board based on ESP32-PICO-D4 SIP, an all-in one package with ESP32, 4MB SPI flash, crystal oscillator, and passive components, which allows for smaller boards. The board is very similar to any other ESP32 boards, and software compatible, but it’s just quite thinner, and easier to work with on breadboards. Since I had already played with Arduino Core and Espruino (JavaScript) on other boards, I used one of the 10 boards provided by Espressif to play with Micropyhon on ESP32. Each winner will get two ESP32 PICO Core board in order to make it worthwhile with regards to shipping costs. To enter the draw simply leave a comment below. Other rules are as follows: Only one entry per contest. I will filter out entries with the same IP and/or […]