touchscreen News - CNX Software - Embedded Systems News

November 16, 2025November 15, 2025 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Eazeye Radiant 15.6-inch portable transflective LCD review

Eazeye Radiant transflective LCD sunlight vs laptop

Eazeye sent me a sample of the Radiant 15.6-inch transflective LCD review for review after I wrote about the Eazeye 2.0 24-inch reflective LCD monitor last August. Yes, there’s been a little bit of miscommunication as I got a transflective LCD (TLCD) launched last year, instead of the new reflective LCD (RLCD). But that’s OK. While those are two different technologies, both monitors are designed to rely on natural light, and I assumed either would perform better outdoors and reduce eye strain compared to traditional portable monitors or laptop displays. Let’s find out. Eazeye Radiant unboxing and specifications I received the portable monitor in a retail box. The main surprise here was that I was expecting a 24-inch monitor, and this looked a little small. I quickly realized the Radiant was a 15.6-inch model instead. We can get part of the specifications on the back side of the package. But […]

November 15, 2025November 15, 2025 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

FireBeetle 2 ESP32-C5 IoT development board offers GDI display interface, LiPo battery support

Just the other day, I lamented the lack of options when it came to ESP32-C5 boards featuring dual-band WiFi 6 support. The FireBeetle 2 ESP32-C5 IoT development board made by DFRobot shows that I needed to be more patient… The ESP32-C5 board features 4MB flash, a USB-C port, a LiPo battery connector, and two GPIO headers for expansion, as well as a GDI display connector designed to add an SPI/I2C touchscreen display. The new RISC-V board has about the same features and form factor as the FireBeetle 2 ESP32-S3. It adds 5 GHz WiFi and an 802.15.4 radio for Zigbee, Thread, and Matter, but loses a camera connector, and comes with less memory and storage. FireBeetle 2 ESP32-C5 specifications: Wireless module – ESP32-C5-WROOM-1-N4 SoC – Espressif Systems ESP32-C5 CPU Single-core 32-bit RISC-V processor @ up to 240 MHz Low-power RISC-V core @ 40 MHz acting as the main processor for […]

November 13, 2025 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Arduino Nesso N1 – An ESP32-C6 IoT wireless development kit with WiFi 6, BLE, 802.15.4, LoRa, and IR transmitter

Arduino Nesso N1 is a new ESP32-C6 IoT development kit with not only 2.4 GHz WiFi 6, Bluetooth LE, and an 802.15.4 radio for Zigbee/Thread/Matter, but also a LoRa radio and an IR transmitter for smart home, industrial, and educational applications. Developed in collaboration with M5Stack, the Nesson N1 also features a 1.14-inch touchscreen display, a 6-axis motion sensor, a few LEDs and buttons, as well as Grove and Qwiic expansion connectors, and an 8-pin GPIO header. Nesso N1 specifications: SoC – Espressif Systems ESP32-C6 CPU Single-core 32-bit RISC-V clocked up to 160 MHz Low-power RISC-V core @ up to 20 MHz Memory/Storage – 320KB ROM, 512KB SRAM Wireless – 2.4 GHz WiFi 6, Bluetooth 5.3, and 802.15.4 radio for Thread/Zigbee Storage – 16MB NOR Flash Display – 1.14-inch touchscreen display with 240 x 135 resolution, 262K colors; ST7789P3 driver, FT6336U capacitive touch Wireless 2.4 GHz WiFi 6, BLE 5.3, Zigbee […]

November 13, 2025November 13, 2025 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

4-inch UGOOS AC1 smart clock features Amlogic A213Y SoC for smart displays and digital signage

UGOOS is better known for its TV boxes, but the company recently introduced a different product with the AC1 smart clock based on an Amlogic A213Y SoC for smart displays and digital signage applications I had never heard of. Let’s have a look at both. UGOOS AC1 smart clock The AC1 smart clock features a 480×480 resolution display, supports Bluetooth pairing, alarms with different ringtones, displays weather, date, time, and sensor data, and supports features such as photo frame, event notes, and music playback. UGOOS AC1 specifications: SoC – Amlogic A213Y (more details below) System Memory – 256MB DDR4 Storage – 8 GB eMMC flash Display – 4-inch IPS touchscreen display with 480×480 resolution; 2.5D glass cover Audio 3W sound speaker Built-in microphone for voice search Wireless – IEEE 802.11b/g/n WiFi 4 and Bluetooth 4.2 Sensors – Temperature and humidity sensor, light sensor Misc – Touch Key, mute switch, and […]

November 11, 2025November 11, 2025 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

Giveaway Week 2025 winners announced!

CNX Software’s Giveaway Week 2025 has just ended and we’ve now ready to announce the winners. We offered some of the review samples we tested, and three companies joined us offering new samples, namely Banana Pi with two router boards, VOIPAC with an industrial development kit, and RAKwireless offered two of their IoT development kits for the fifth year running. Besides the aforementioned prize, we also included an ESP32-P4 development kit, a dry switch from SONOFF, a Raspberry Pi CM4-based HMI with a 915MHz LoRa module, a 5-inch Raspberry Pi Touch Display, and two USB PD voltage indicators on both CNX Software “International” and CNX Software Thailand. You can see all prizes shown below. Without further ado, here are the seven winners of Giveaway Week 2025 on CNX Software (English): M5Stack M5Tab – Ed, Canada Elecrow Pi Terminal – Tom, Finland Banana Pi BPI-R4 Lite router board – Stef, Belgium […]

November 6, 2025November 8, 2025 by Jean-Luc Aufranc (CNXSoft) - 261 Comments

Giveaway Week 2025 – 5-inch Raspberry Pi Touch Display 2

The fourth prize of CNX Software Giveaway Week 2025 will be the official 5-inch Raspberry Pi Touch Display 2. I was sent one for review, but I have yet to find anything interesting to use it for, like I did for the 7-inch Raspberry Pi Touch Display 2 and the Raspberry Pi AI camera. So I might just as well give it away. To enter the draw, simply leave a comment with your country and whatever else you’d like to say (no links in the body of the comment). If the country is missing, I’ll consider the entry void. Other rules are as follows: Only one entry per contest. I will filter out entries with the same IP and/or email address. Contests are open for 48 hours starting at 10 am (Bangkok time) every day. Comments will be closed after 48 hours. If comments are open, the contest is still […]

November 4, 2025November 6, 2025 by Jean-Luc Aufranc (CNXSoft) - 272 Comments

Giveaway Week 2025 – Elecrow Pi Terminal Raspberry CM4 industrial HMI display

Elecrow CrowPanel CM4 Pi Terminal Demo application

Sometimes we receive samples even though we did not ask for them, said we would have time to review them, or due to miscommunication. That’s exactly what has happened with the Elecrow Pi Terminal, a Raspberry Pi CM4-powered industrial HMI with a 7-inch touchscreen display. So instead of letting it go to waste, I decided to offer it as the second prize of the CNX Software Giveaway Week 2025 contest. Elecrow Pi Terminal specifications: SoM – Raspberry Pi CM4 Lite SoC – Broadcom BCM2711 CPU – Quad-core Cortex-A72 SoC @ 1.5GHz GPU – VideoCore VI with support for OpenGL ES 3.1 and Vulkan 1.0 VPU Decode – H.265/HEVC up to 4Kp60, H.264 up to 1080p60 Encode – H.264 up to 1080p30 Memory – 4GB LPDDR4-3200 Storage – N/A Wireless – Dual-band WiFi 5 and Bluetooth 5.0 Storage 64GB microSD card preloaded with the Raspberry Pi OS + Node-RED software M.2 […]

November 3, 2025November 5, 2025 by Jean-Luc Aufranc (CNXSoft) - 269 Comments

Giveaway Week 2025 – M5Stack Tab5 ESP32-P4 IoT devkit

It’s that time of the year when we organize CNX Software Giveaway Week, a global contest where we give away review samples or get companies to send units to readers. For the 12th edition of the contest, we have seven items to give away this time around: five review samples I will send myself, and two prizes from companies offering a router board and an industrial development kit. As usual, the contest is open worldwide, and CNX Software Thailand has a separate contest with four additional items for people with an address in Thailand. The first prize will be the M5Stack Tab5 ESP32-P4 IoT development kit featuring a 5-inch touchscreen display, a 2MP front-facing camera, a speaker, a dual-microphone array, a microSD card slot, an ESP32-C6 for wireless connectivity, sensors, and more. I had some fun reviewing the M5Stack Tab5 devkit by building the default firmware with the ESP-IDF framework, […]