waveshare News - Page 2 of 6 - CNX Software

February 28, 2024February 27, 2024 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Waveshare RP2040-BLE is a Raspberry Pi RP2040 module with Bluetooth LE connectivity

If you could not care less about WiFi, the Waveshare RP2040-BLE module combines a Raspberry Pi RP2040 microcontroller with an unnamed Bluetooth 5.1 dual-mode chip, and supports a USB-C add-on board useful during development. There are several Raspberry Pi RP2040 boards with a WiFi and Bluetooth module including the Raspberry Pi Pico W, but if you are only interested in using Bluetooth, the RP2040-BLE board from Waveshare may be more power-efficient and its design may be more suitable for integration into products. Waveshare RP2040-BLE specifications: MCU – Raspberry Pi RP2040 dual-core Arm Cortex M0+ microcontroller up to 133 MHz with 264KB of SRAM Storage – 2MB of onboard Flash memory. Connectivity Bluetooth 5.1 dual-mode function (BLE and classic) Controlled by serial AT commands Ceramic antenna Expansion 24x through and castellated holes with 14x multi-function GPIO pins. 2x SPI, 2x I2C, 2x UART, 3x 12-bit ADC, 14 x PWM FPC connector […]

February 22, 2024February 21, 2024 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Waveshare R7FA4 PLUS A and B boards are clones of the Arduino UNO R4 Minima and WiFi

Arduino board clones have been around for many years, but I don’t think I have ever seen clones of the new Renesas-based Arduino boards so far. Waveshare changes that with the R7FA4 PLUS A that clones with Arduino UNO R4 Minima, and the R7FA4 PLUS B board duplicating the Arduino UNO R4 WiFi. The Waveshare boards are not 100% clones with some small differences in the PCB layout, support for 5V and 3.3V shields, an additional 6-pin “power output header” with 5V, 3.3V, and GND signals, and a USB communication jumper to select between the Espressif ESP32-S3 and Renesas RA4M1 microcontrollers. Waveshare R7FA4 PLUS A and B specifications: Microcontroller – Renesas RA4M1 Arm Cortex-M4F MCU @ 48 MHz with 32KB SRAM, 256KB flash Wireless (B model only) – ESP32-S3-MINI-1 module based on ESP32-S3 dual-core Xtensa LX7 microcontroller with 512KB SRAM, 384KB ROM, WiFi 4 and Bluetooth 5.0 connectivity, PCB antenna […]

February 20, 2024February 19, 2024 by Debashis Das - 3 Comments

Waveshare ESP32-S3 4G dev boards feature LTE Cat-1, 2G, and camera support

Waveshare has recently launched two new ESP32-S3 4G dev boards – the ESP32-S3-SIM7670G-4G and the ESP32-S3-A7670E-4G. These boards support 4G LTE Cat-1, Wi-Fi, Bluetooth, and GNSS, and come with an OV2640 camera, and a battery holder for a 18650 battery. The main difference between the two is that the A7670E module also supports 2G GSM/GPRS/EDGE at 900/1800MHz while the SIM7670G module does not. The board has two rows of I/Os including GPIO, I2C, SPI, ADC, and USB 2.0. It also has a USB-C port for power and programming, a slot for a MicroSD card, and an option to connect an external speaker. There’s a USB switching IC and DIP switch for easily connecting the module to a PC for internet or debugging. Waveshare ESP32-S3 4G Dev Boards Specification: Communication module A7670E 4G – A7670E Cat-1 4G module supporting 4G Cat-1 + 2G networking, GNSS positioning, telephone calls, and SMS. SIM7670G […]

February 15, 2024February 16, 2024 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Waveshare RP2040-GEEK USB development board features RP2040 MCU, 1.14-inch color display, UART/I2C/SWD ports

Waveshare RP2040-GEEK is a development board that looks like a USB flash drive but is based on a Raspberry Pi RP2040 microcontroller with a 1.14-inch 65K color LCD and some expansion ports all housed in a white plastic case. The device comes with a 4MB flash to store the firmware, a microSD card slot for data storage, a BOOT button to enter bootloader mode, two 3-pin connectors for UART and SWD debug, and a 4-pin I2C port. Waveshare RP2040-GEEK specifications: MCU – Raspberry Pi RP2040 dual-core Arm Cortex-M0+ microcontroller clocked up to 133 MHz with 264 kB SRAM Storage – 4MB flash (W25Q32JVSSIQ) and microSD card slot Display – 1.14-inch 240×135 pixel 65K color IPS LCD display USB – 1x USB Type-A female port for power and programming Debugging – 3-pin SWD port for connecting a target board; the standard CMSIS-DAP interface can be used to debug most Arm-based microcontrollers; […]

February 6, 2024February 6, 2024 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

Solar power manager module supports 6V-24V input range, battery charging, MPTT function, and outputs 5V/3A

Waveshare Solar Power Manager Module (D) is a compact power module for solar panels with support for 6V to 24V input, MPTT (Maximum Power Point Tracking), and battery charging. It outputs 5V up to 3A via a USB-C port or terminal block and should be suitable for a range of projects. A few weeks ago, we wrote about the FireBeetle 2 ESP32-C6 IoT development board with DFRobot highlighting support for solar charging of lithium batteries thanks the the CN3165 chip. But with a range of just 4.5 to 6V for solar panel input and a lack of support for MPTT, several readers were unimpressed by the solution. The Waveshare Solar Power Manager Module (D) recently popped up in my news feed, and I thought it might be worth a look. Waveshare Solar Power Manager Module (D) specifications: Solar panel input 6V to 24V via DC jack or 2-pole screw terminal […]

January 25, 2024 by Debashis Das - 1 Comment

Waveshare ESP32-S3-LCD-1.28 development board with 1.28-inch IPS round LCD is available for $15

The Waveshare “ESP32-S3-LCD-1.28” is an ESP32-S3-based display board featuring a 1.28-inch round LCD screen with a 240×240 resolution, driven by the GC9A01 display driver chip. It also includes a Li-ion battery charger, a QMI8658 6-axis IMU (for motion tracking), a USB Type-C connector, and wireless capabilities. This board is quite similar to others like the Lilygo T-RGB, Round Display for XIAO, ESP32-S3 Round SPI boards. However, it’s thinner and more affordable. Waveshare ESP32-S3-LCD-1.28 development board specifications: Wireless MCU – ESP32-S3 Xtensa 32-bit LX7 dual-core, up to 240MHz frequency. Display: 1.28-inch round IPS LCD. Resolution – 240×240 pixels. 65K color. Display Chip – GC9A01A. IMU Parameters: Sensor – QMI8658 Accelerometer resolution – 16-bit; Range (Optional): ±2, ±4, ±8, ±16g. Gyroscope resolution – 16 bits; Range (Optional) – ±16, ±32, ±64, ±128, ±256, ±512, ±1024, ±2048°/sec. Memory: Built-in 512KB SRAM. 384KB ROM. Onboard 2MB PSRAM. External 16MB Flash memory (W25Q128JVSIQ). Wireless Connectivity: […]

January 22, 2024January 22, 2024 by Debashis Das - 5 Comments

Waveshare PCIe to M.2 adapter for Raspberry Pi 5 will only cost you $8.99

The Waveshare PCIe To M.2 adapter is an inexpensive PCIe to M.2 HAT+ module for the Raspberry Pi 5 designed for PCIe Gen2 and Gen3 SSDs. It is compatible with standard SSD sizes of 2230/2242 and features status indicator LEDs, a power monitoring chip, an EEPROM, and a cooling fan vent to keep temperatures in control during heavy use. It’s not the first Raspberry Pi 5 adapter taking NVMe SSDs (or AI accelerator), as we previously explored the PineBerry Pi’s HatDrive, suitable for 2230, 2242, and 2280 SSDs up to PCIe Gen3 speeds and the Pimoroni NVMe Base with a different design and compatible with 2230, 2242, 2260, and 2280 drives up to PCIe Gen3 speeds. A few days ago, we already covered Waveshare’s PoE HAT(F), which shares a similar form factor with Waveshare PCIe To M.2 Adapter and uses the new HAT+ standard to provide 24W of power to […]

January 18, 2024January 18, 2024 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Raspberry Pi 5 gets a PoE HAT+ kit that doubles as a cooling solution

Waveshare PoE HAT(F) is an 802.3af/at-compliant 24W Power-over-Ethernet (PoE) HAT+ board designed for the Raspberry Pi 5 that also cools the SBC with its embedded fan, a heatsink, and two thermal pads. The Chinese company has beaten Raspberry Pi to it as the UK company is working on releasing the L-shaped 25W “PoE+ HAT(+) for Raspberry Pi 5” a little later. The existing official Raspberry Pi PoE+ HAT delivers up to 25.5 Watts which would be enough to power the Pi 5, but since the PoE header has been moved to another location, it’s not compatible anymore, so new solutions are needed such as the Waveshare PoE HAT(F). Waveshare PoE HAT(F) specifications: Supported SBC – Raspberry Pi 5 only Connected via 40-pin Raspberry Pi GPIO header and 4-pin PoE header PoE (Power Over Ethernet) IEEE 802.3af/at-compliant Input voltage – 37V-57V DC input Output 2-pin header – 12V/2A max GPIO header […]