GL.iNet Flint 2 router review – Part 2: WiFi 6, 2.5GbE, WireGuard performance

GL.iNet Flint 2 Review

In the first part of the review of the GL.iNet GL-MT6000 “Flint 2” WiFi 6 router, I had a look at the package content and the hardware design with a teardown of the router, and quickly tried it out. I’ve now had more time to play with the router focusing the review on WiFi 6 and 2.5GbE performance, and checking whether of 900 Mbps Wireguard VPN claim had any truth to it. The router also supports the Tor network to anonymously browse the web, Adguard Home to get rid of unwanted ads, and Repeater mode among other features. Those all work with the Fliont 2 router, but I won’t cover those in detail here, and invite you to check out the GL.iNet Brume 2 security gateway review for Tor and Adguard Home and the GL.iNet Beryl AX review for the repeater mode test. Connecting wired and wireless clients The Flint […]

GL.iNet Flint2 AX6000 router supports up to 900 Mbps WireGuard VPN with MediaTek MT7986 SoC

Flint2 router

GL.iNet Flint2 (also known as GL-MT6000) is a new AX6000 router based on MediaTek MT7986 (Filogic 830) Arm SoC and supporting VPN speeds of up to 900 Mbps using WireGuard and 190 Mbps with OpenVPN. This caught my attention, as I previously covered other GL.iNet routers such as the Spitz AX (GL-X3000NR) and the Beryl AX (GL-MT3000) based on the previously generation Filogic 820 (MT7981B) CPU with claims of (only) 300 Mbps transfer rates with Wireguard, so the new model is supposed to triple the VPN performance. GL.iNet Flint2 (GL-MT6000) specifications: SoC – MediaTek MT7986 (Filogic 830) quad-core Arm Cortex A53 processor @ 2.0 GHz with hardware acceleration engines for Wi-Fi offloading and networking System Memory – 1GB DDR4 Storage – 8GB eMMC flash Networking 2x 2.5 Gbps Ethernet ports 4x Gigabit Ethernet LAN ports 802.11b/g/n/ac/ax WiFi 6 with 4x external Wi-Fi antennas Up to 1,148 Mbps @ 2.4 GHz […]

GL.iNet Spitz AX review – Part 2: a router with 5G NR, WiFi 6, 2.5GbE, failover and load balancing

Gl.iNet Spitz AX review 5G failover testing

Earlier this month I introduced the GL.iNet Spitz AX (aka GL-X3000NR) router with 2.5GbE, WiFi 6, and 5G NR cellular connectivity listing the specifications, doing an unboxing, and going through the initial setup. I’ve now received a new SIM card for testing and installed it into the router to continue the review. 4G/5G cellular connectivity on Spitz AX router After powering the router, the SIM card was detected and showed a 5G connection, but quickly fell back to 4G as can be seen with the cyan icon in the screenshot below. Shortly after, I lost 4G data connectivity, and after a while, the modem was not detected at all. But after restarting the router, and clicking on the “Auto Setup” icon everything looked to be working fine and I was always on a 5G connection from “house 1”. You’ll notice an envelop icon on the top right corner of the […]

How to setup a WireGuard server on Ubuntu for remote login

WireGuard Server Network Topology

In this article, we will show you how to set up a WireGuard server on Ubuntu in order to use it for remote login. Introduction to WireGuard First of all, let’s first understand, what is WireGuard? WireGuard is a very simple and fast VPN tool with state-of-the-art encryption. Its goal is to be faster, simpler, more streamlined, and easy to use than IPsec, while avoiding the hassle of large-scale configuration. WireGuard is designed as a general-purpose VPN to run on embedded interfaces and supercomputers in many different environments. Originally released for the Linux kernel, WireGuard is now widely deployed and supported across platforms (Windows, macOS, BSD, iOS, Android). WireGuard is growing rapidly and is already considered the most secure, easiest-to-use, and simplest VPN solution in the industry. Basic Concepts of WireGuard Several basic concepts are involved in WireGuard: Peer: A node in WireGuard. Private key: Each node has its own […]

Getting Started with GL-S200 Thread Border Router kit

Getting Started GL-S200 Thread Border Router

Last week we checked out the hardware for the GL.iNet GL-S200 Thread Border Router kit with three nRF52840 Thread Dev Boards, and I’ve now had time to work with the kit, so I’ll report my getting started experience in the second part of the review. GL-S200 Initial Set Up I connected the WAN port to my Ethernet Switch itself connected to my modem router and the LAN port to my laptop, so I could access the web interface using the default IP address (192.168.8.1). The GL-S200 uses the same Admin Panel as other GL.iNet routers such as the Beryl AX router we reviewed at the beginning of the year. You’ll be greeted by a wizard to let you select the language and set a new password for the Admin Panel, and once you’re done you’ll have access to the familiar GL.iNet Admin Panel 4.x.x. After completing the wizard, the system […]

GL.iNet Beryl AX OpenWrt router review – WiFi 6 performance, repeater, NAS, and 4G hotspot modes

Power bank GL.iNet GL-MT3000 Beryl AX router

In the first part of the review of GL.iNet GL-MT3000 “Beryl AX” pocket-size WiFi 6 OpenWrt router we had a look at the specifications, the package content, and the hardware design with a teardown of the little router. I’ve now had more time to play with the router focusing the review on WiFi 6 performance, and some of its functions such as repeater, NAS, and 4G hotspot. The router also supports VPN client and server modes, the Tor network, and Adguard Home, but I’ll invite readers to check out the GL.iNet Brume 2 security gateway review since I went through all these, and the hardware is very similar minus wireless connectivity. Initial setup of the Beryl AX router If you connect an Ethernet cable to the router you can switch to step two. If you only rely on WiFi for the setup that works too as the Beryl AX router […]

GL.iNet GL-MT3000 pocket-sized Wi-Fi 6 Router review – Part 1: Specs, unboxing, and teardown

GL-MT3000 portable WiFi 6 router

GL.iNet Beryl AX (GL-MT3000) is a pocket-sized Wi-Fi 6 router running OpenWrt on a MediaTek MT7981B (Filogic 820) dual-core processor @ 1.3 GHz and equipped with a 2.5GbE port, a Gigabit Ethernet port, and a USB 3.0 port. The hardware is basically the same as the Brume 2 (GL-MT2500A) security gateway, except it adds support for WiFi 6 connectivity and as an AX3000 router more than doubles the bandwidth compared to the earlier Beryl (GL-MT1300) AC1300 router. The company has sent me a sample so I’ll start the two-part review by checking the specifications, doing an unboxing, and tearing it down to have a closer look at the hardware design, before trying out OpenWrt and testing WiFi 6 and 2.5GbE performance in the second part of the review. GL.iNet GL-MT3000 specifications Beryl AX specifications: SoC – MediaTek MT7981B (Filogic 820) dual-core processor @ 1.3 GHz System Memory – 512MB DDR4 […]

Brume 2 router review with WireGuard, OpenVPN, Tor, and Adguard Home

Brume 2 review

We started the review of GL.inet GL-MT2500A security gateway, aka Brume 2, with an unboxing and teardown, and I’ve now had time to test the router in more detail so I’ll report my experience using the router with OpenVPN and WireGuard VPN, Tor, Adguard Home, and more. In a nutshell, it’s super easy to use, unless your ISP causes troubles, which it did in this case. Brume 2 connection and initial setup I connected the WAN port of the Brume 2 router to 3BB’s modem router (3BB is an ISP in Thailand), the LAN port to my laptop, and finally the USB-C power supply (power draws is 2.3 Watts at idle). Let’s now go to the dashboard using the default IP (192.168.8.1). This will take us through the configuration wizard to select the language and set up the admin password. I was then immediately greeted by an “Upgrade Reminder” and […]

EmbeddedTS embedded systems design