96Boards HiChips Parrot Board and 3-Mic Array Work with Amazon Alexa

96boards Parrot Board Amazon-AVS 3-Mic far field board

Early last year, Banana Pi unveiled Allwinner SoC-Only 3-Mic Far-Field Development Kit for Amazon AVS, a board powered by Allwinner R18 processor extended with an external 3-mic array board, officially supported by Amazon Alexa Voice Service (AVS), and sold for $129 plus shipping. There’s now a compatible board following 96Boards CE Extended form factor, and selling for just $79.99 plus shipping on Alibaba or 555.99 CNY on 1688.com. The board looks almost the same as the original 3-Mic far-field development kit, apart from the LS and HS connectors found in the 96Boards hardware platforms. Hichips Parrot board should not be confused with Allwinner R16 based Parrot board that was used by Allwinner internally, and never made available to the general public. Hichips Parrot board specifications: SoC – Allwinner R18 quad-core Cortex-A53 processor @ 1.15GHz with Mali400MP2 GPU System Memory – 1GB DDR3 Storage – 8GB eMMC flash, micro SD card […]

NXP Immersiv3D Enables DSP-Free Dolby Atmos & DTS:X Audio Systems

NXP Immersiv3d audio reference design

High-fidelity audio systems such as soundbars, smart speakers, and AV receivers have traditionally relied on DSPs (Digital Signal Processors) to deliver low-latency audio processing, and enable audio and video synchronization. DSPs add to the cost of the overall design however, and with Immersiv3D technology, NXP has leveraged Arm Cortex-A53 and M4 cores in their NXP i.MX 8M Mini processor to completely remove the need for DSP in audio systems, shaving the BoM cost by up to 20%  according to an article on EETimes. Immersiv3D also enables immersive audio support with Dolby Atmos and DTS:X, advanced audio pre/post processing, advanced features like voice control for the smart home. Immersiv3D audio solution was designed to help OEMs to bring to market affordable consumer audio devices with Dolby Atmos and DTS:X, and beside the audio processing software, NXP is also offering an Immersiv3D audio reference design to help them delelop sound bars based […]

Sony Spresense Board Review with NuttX based Spresense SDK

Sony Spresence Kit Assembled

Sony Spresense Arduino compatible board with audio and global navigation satellite systems (GNSS) support and its extension board launched in Japan this summer. The company has now expanded markets, and is offering the boards in the United States and Europe as well. They also tasked an agency to send samples to various reviewers, and I got selected to receive one as well. I’ll start the review by checking out the hardware, shortly discuss software development options, and report my experience with Spresense SDK. Sony Spresense Unboxing I received two packages… … one the main board, and the other for the extension board. The main board package only comes with CXD5602PWBMAIN1 board and an information sheet. The top of the board includes a reset button, four user LEDs, a power LED, a boot recovery button, the camera interface, Sony CXD5247 power management and audio analog interface chip (Black on the photo below, […]

This Amplifier Board Features Beken BK3266 Bluetooth 5.0 Audio SoC

Bluetooth 5 audio board

I’ve been writing about a few Bluetooth 5.0 solutions this year, but in most case those were based on Nordic Semi nRF52 chips which do support BT 5.0 Low Energy, but not Bluetooth classic which means they are suitable for HID devices, but not for all applications such as potentially some Bluetooth audio application. I’ve just come across a $10.59 audio amplifier board on IC station that is supposed to support Bluetooth 5.0 via Beken BK3266 Bluetooth audio chip. Specifications and features listed for the board: Bluetooth 5.0 Connectivity Up to 6 paired devices Bluetooth protocols – HFPV1.7, A2DPV1.2, AVRCPV1.5, AVCTPV1.2, AVDTPV1.2 Range up to 10 meters Transmission Power – Class2, 4dbm Sensitivity – -81dBm < 0.1% BER Frequency Range – 2.402GHz – 2.480GHz Audio MP3/WMA/WAV music format Speaker Impedance – 4 to 8 Ohm Output Power –  2x15W at 16V/4A, 2x10W at 12V/4A Audio signal to noise ratio >75dB […]

Up2Stream WiFi Audio Receiver Module Targets DIY Wireless Speakers

WiFi Speaker DIY Kit

If you own a set of very good speakers, and are interested in making them smarter, Arylic Up2Stream WiFi audio receiver module may be a solution to look into. The module allows to make your own DIY wireless speakers by adding WiFi connectivity, and features such as multiroom, AirPlay, DLNA streaming, Spotify, and Internet radio streaming. Up2Stream (WA31) hardware specifications: SoC – MediaTek MT7688AN MIPS processor @ up to 580 MHz System Memory – 64MB DDR2 Storage – 16MB flash Connectivity – 2.4GHz 802.11 b/g/n 1T1R WiFi up to 150 Mbps with 5 dBi I-PEX antenna Audio – 24-bit / 192 KHz decoding, 20 Hz – 20KHz frequency range, 4-pin speaker connector with 2.0mm pitch USB – 1x USB 2.0 port port Power Supply – 5VDC / 1A via 2-pin header (2.0mm pitch) Power Consumption – 160 to 320 mA Dimensions – 55.21 x 41.37mm The module ships with a […]

Rakoit KM200 Karaoke Audio Mixer Supports 4K Videos

4K Karaoke Audio Mixer

While there are plenty of karaoke systems on Aliexpress, it’s pretty hard to find one that supports 4K videos, and Rakoit KM200 karaoke audio mixer is one of the rare that do. You’d just need to add your own 4K TV box / media player / computer, 4K UHD television, one or two microphones, and you’re ready to go. Rakoit KM200 specifications: Audio & Video In/Out HDMI output and HDMI input with 4K2K video support RCA jack for composite and stereo audio output and input 2x MIC Line-in Controls – 2x MIC volume adjust button, main volume adjust, echo volume adjust, earphone slot Power Supply – 12V DC Beside audio mixing, the device works as an amplifier, and supports 1080p to 4K upscaling. The karaoke mixer ships with an HDMI cable, an RCA cable, and a power adapter. Rakoit KM200 now sells for $99 on Acrylic.com, but you’ll also find […]

Three Add-on Boards for UP Board and UP Squared – UP-AUDIO HAT, UP-CAMERA HAT, UP-POE HAT

AAEON has announced three add-on boards for their Intel based UP board (Cherry Trail) and UP Squared board (Apollo Lake): UP-AUDIO HAT –  Features external ports for a microphone and speakers/headphones UP-CAMERA HAT – Comes with two FPC/FFC connectors for 2M security camera UP-POE HAT – Adds WAN and LAN Gigabit Ethernet ports and PoE support UP-AUDIO HAT AAEON’s UP-Audio HAT currently only works with UP board, and features the following: Audio Codec – Realtek ALC5672 3.5mm Audio Jacks – 1x Line out, 1x MIC Headers – 2x speaker Built-in Components – 2x digital microphones, 1x buzzer Connects to board via 40-pin GPIO female header Dimensions – 85 mm x 56 mm The board is supported in Windows 10, Android 6, and Ubuntu 16.04. UP-CAMERA HAT The camera board works with UP Board, UP Squared and UP Core boards. UP-CAMERA HAT specifications & features: 2x MIPI CSI-2/ DSI DPHY Re-timer […]

Sony SPRESENSE Arduino Compatible GNSS + Audio IoT Board To Sell for $50 (in Japan)

Sony-Spresense-Arduino-Board

Last year,  we covered Sony Spritzer, an Arduino compatible with a Sony hexa-core Arm Cortex-M4F micro-controller, a built-in GNSS receiver, and an audio codec. The product page for this product is now gone, but it appears Sony only renamed it to SPRESENSE, made some design modifications, and is ready to launch the main board for 5,500 JPY (~$50), and the extension board for an extra 3,500 JPY ($32) on July 31, 2018. Sony SPRESENSE main board (CXD5602PWBMAIN1) specifications: MCU – Sony CXD5602 ARM Cortex-M4F ×6 micro-controller clocked at up to 156 MHz with 1.5MB SRAM Storage – 8MB Flash Memory GNSS – GPS & GLONASS Audio – 3.5mm audio jack Expansion I/Os Digital I/O Pins – GPIO, SPI, I2C, UART, PWM, I2S Analog Pins – 2ch (0.7V range) Camera interface USB – 1x micro USB port for programming and power Power Supply – 5V via micro USB port Dimensions – […]

Exit mobile version
Memfault IoT and embedded debugging platform