ble

Posted on by Jean-Luc Aufranc (CNXSoft) - 1 Comment on Intrinsyc Open-Q 835 Development Kit Features Qualcomm Snapdragon 835 Processor, Support Android 7 and Windows 10

Intrinsyc Open-Q 835 Development Kit Features Qualcomm Snapdragon 835 Processor, Support Android 7 and Windows 10

Intrinsyc has just launched one of the first development boards powered by Qualcomm Snapdragon 835 processor with their Open-Q 835 devkit equipped with 4GB LPDDR4x, 128GB UFS 2.1 flash, 802.11ad WiFi, dual camera support and more. Open-Q 835 development kit is comprised of a “processor board” and a baseboard with the following specifications: Processor Board SoC – Qualcomm Snapdragon 835 (APQ8098) octa-core processor with four high performance Kryo 280 cores @ 2.20 GHz/ 2.30 GHz (single core operation), four low power Kryo cores @ 1.9 GHz, Adreno 540 GPUwith  OpenGL ES 3.2, OpenCL 2.0 Full support, and Hexagon 682 DSP with Hexagon Vector eXtensions (dual-HVX512) System Memory – 4GB LPDDR4x RAM Storage – 128GB UFS2.1 Gear3 2 lane Flash Connectivity Wi-Fi 802.11a/b/g/n/ac 2.4/5Ghz 2×2 Bluetooth 5.0 + BLE WiGig60 802.11ad with on-board antenna Dimensions – 70 x 60 mm Carrier Board Display – 1x HDMI 2.0 out up to 4K Ultra […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 3 Comments on Olimex ESP32-EVB Board with Ethernet, CAN Bus, and Relays up for Sale for 26 Euros

Olimex ESP32-EVB Board with Ethernet, CAN Bus, and Relays up for Sale for 26 Euros

One of the new feature of Espressif ESP32 SoC over ESP8266 is the inclusion of an Ethernet MAC interface, but so far few boards come with an RJ45 jacks. ESP32 Monster board is an option, also including an OLED Display and CAN Bus, and sold on Tindie for $35, but Olimex has now stocked their ESP32-EVB board with Ethernet, CAN Bus, and two relays, and you can purchase it for 26 Euros per unit, and less in larger quantities. Olimex ESP32-EVB Rev. B specifications: Wireless Module – ESP32-WROOM32 module with 802.11 b/g/n WiFi and Bluetooth LE Wired Connectivity – 10/100M Ethernet with RJ45 jack (via LAN8710A) External Storage – micro SD slot Relays – 2x 10A/250VAC relays with LED status Expansion 40-pin GPIO female header (2.54mm pitch) UEXT connector for sensors and modules CAN Bus USB – 1x micro USB port for debugging (CH340T) and power Misc – Reset and […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 3 Comments on STMicro Unveils STM32L4 Discovery Kit for IoT with WiFi, BLE, NFC, Sub-GHz RF, and Plenty of Sensors

STMicro Unveils STM32L4 Discovery Kit for IoT with WiFi, BLE, NFC, Sub-GHz RF, and Plenty of Sensors

STMicro has recently introduced B-L475E-IOT01A Discovery kit powered by STM32L4 Cortex-M4 and targeting IoT nodes with a choice of connectivity options including WiFi, Bluetooth LE, NFC, and sub-GHZ RF at 868 or 915 MHz, as well as a long list of various environmental sensors. B-L475E-IOT01A Discovery kit key features and specifications: MCU – STM32L4 Series MCU based on ARM Cortex -M4 core with 1 MB Flash memory, 128 KB SRAM Storage – 64 Mbit (8MB)  Quad-SPI Flash memory (Macronix) Connectivity Bluetooth 4.1 LE module (SPBTLE-RF) Sub-GHz (868 or 915 MHz) low-power-programmable RF module (SPSGRF-868 or SPSGRF-915) Wi-Fi module based on Inventek ISM43362-M3G-L44 (802.11 b/g/n compliant) Dynamic NFC tag based on M24SR with its printed NFC antenna Sensors 2x digital omni-directional microphones (MP34DT01) Capacitive digital sensor for relative humidity and temperature (HTS221) 3-axis magnetometer (LIS3MDL) 3D accelerometer and 3D gyroscope (LSM6DSL) 260-1260 hPa absolute digital output barometer (LPS22HB) Time-of-Flight and gesture-detection […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 5 Comments on Arduino Cinque Combines SiFive RISC-V Freedom E310 MCU with ESP32 WiFi & Bluetooth SoC

Arduino Cinque Combines SiFive RISC-V Freedom E310 MCU with ESP32 WiFi & Bluetooth SoC

SiFive introduced the first Arduino compatible board based on RISC-V processor late last year with HiFive1 development board powered by Freedom E310 MCU, but  the company has been working with Arduino directly on Arduino Cinque board equipped with SiFive Freedom E310 processor, ESP32 for WiFi and Bluetooth, and an STM32 ARM MCU to handle programming. Few other technical details have been provided for the new board, but since it looks so similar to HiFive1, I’ve come with up with preliminary/tentative Arduino Cinque specifications: MCU – SiFive Freedom E310 (FE310) 32-bit RV32IMAC processor @ up to 320+ MHz (1.61 DMIPS/MHz) WiSoC – Espressif ESP32 for WiFi and Bluetooth 4.2 LE Storage – 32-Mbit SPI flash I/Os 19x Digital I/O Pins 19x external interrupt pins 1x external wakeup pin 9x PWM pins 1/3 SPI Controllers/HW CS Pins I/O Voltages –  3.3V or 5V supported USB – 1x micro USB port for power, […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 5 Comments on SHA2017 Conference Badge To Feature ESP32 SoC, e-Paper Display

SHA2017 Conference Badge To Feature ESP32 SoC, e-Paper Display

In most conference, you’ll wear a badge showing your name, job description and company, but with the price of electronics going down, it may be time for a conference badge upgrade. SHA2017 is a non-profit outdoor hacker camp taking place in The Netherlands in 2017 on August 4 – 8, and the organizers are planning to use a special badge comprised of Espressif ESP32 processor, and an e-Paper Display. SHA2017 Badge specifications: Wireless Module – Espressif ESP32 based ESP-WROOM-32 module with WiFi and Bluetooth Display – 2.9″ e-paper display (296×128) Storage – micro SD slot Expansion – 12-pin expansion header with GPIOs, I2C, 3.3V, GND Debugging – micro USB port + USB->TTL chip for programming Misc – Direction keys, select, start, A and B buttons for input; 6x RGB, LEDs; pager motor for notifications Battery – Battery sized to last at least a day Beside your name and company details, […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 5 Comments on Smartwatch for the Blind – Dot Watch Supports Braille Language, Sync Data over Bluetooth

Smartwatch for the Blind – Dot Watch Supports Braille Language, Sync Data over Bluetooth

A South Korean company has created Dot smartwatch specifically designed for the blinds and visually impaired, as it supports Braille language through 24 dots that move up or down depending on the data to show. Like other smartwatches, it will also pair with a smartphone, and received notifications over Bluetooth to Android and iOS smartphones. Dot watch specifications: Wireless MCU – 32-bit ARM Cortex M4F + Cortex M0 microcontroller “Display” – 4 Dot Cells (24 Dots) made of 6000 series silver aluminum Connectivity – Bluetooth LE 4.2 Misc – 24 touch sensors, shaft horizontal vibration motor, a crown, two buttons Battery – 400mAh li-polymer battery good for a typical 7 days on a charge Dimensions – Watch: 43mm x 12.5mm; Leather band – S size: 22x220mm; M size: 22x250mm; L size: 22x290mm Weight – 27g This is all made possible through the company’s dot rotor technology that allows to move […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 18 Comments on Getting Started with ESP32-Bit Module and ESP32-T Development Board using Arduino core for ESP32

Getting Started with ESP32-Bit Module and ESP32-T Development Board using Arduino core for ESP32

Espressif ESP32 may have launched last year, but prices have only dropped to attractive levels very recently, and Espressif has recently released released ESP-IDF 2.0 SDK with various improvements, so the platform has become  much more interesting than just a few weeks ago. ICStation also sent me ESP32-T development board with ESP32-bit module, so I’ll first see what I got, before trying out Arduino for ESP32 on the board. ESP32-T development board with ESP-bit Module – Unboxing & Soldering One thing I missed when I asked for the board is that it was not soldered, and it comes in kit with ESP32-bit module in one package, and ESP32-T breakout board with headers in another package. The 21.5x15mm module is based on ESP32-DOWNQ6 processor with 32 Mbit (4MB) of flash, a chip antenna, and a u.FL connector. The module is apparently made by eBox, and also used in Widora board with […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 3 Comments on Intrinsyc Introduces Open-Q 2100 SoM and Devkit Powered by Qualcomm Snapdragon Wear 2100 SoC for Wearables

Intrinsyc Introduces Open-Q 2100 SoM and Devkit Powered by Qualcomm Snapdragon Wear 2100 SoC for Wearables

Qualcomm unveiled Snapdragon Wear 2100 SoC for wearables early last year, and since then a few smartwatches powered by the processor – such as LG Watch Style and Watch Sport – have been launched, and Intrinsyc has now unveiled one of the first module based on the processor with Open-Q 2100 system-on-module, and a corresponding Nano-ITX baseboard. Open-Q 2100 SoM specifications: SoC – Qualcomm Snapdragon Wear 2100 (APQ8009W) quad core ARM Cortex A7 processor @ up to 1.094 GHz with Adreno 304 GPU System Memory – 512 MB LPDDR3 Storage – 4GB eMMC flash Connectivity – 802.11 b/g/n WiFi (WCN2320), Bluetooth 4.1 LE, Gen 8C GNSS (GPS/GLONASS) with on-board u.FL connector (WGR7640) Audio – Integrated Codec/PMIC (PM8916-1) with optional support for Fluence HD, Snapdragon Voice Activation, and Snapdragon Voice+ 2x 100-pin board-to-board connectors with USB 2.0, I2S, GPIO, MIPI DSI up to 720p @ 60 Hz, 2-lane MIPI CSI, SDC2/microSD […]

Exit mobile version