devkit News - Page 48 of 60 - CNX Software

November 2, 2012November 2, 2012 by Jean-Luc Aufranc (CNXSoft) - No Comments

199 Euros “Energy Harvesting Solution To Go” Kit with Energy Micro Cortex M3 Starter Kit

If you’re interesting in battery less ultra low power applications, Energy Micro, Linear Technology and Würth Elektronik have announced an energy harvesting development platform early last month. The “Energy Harvesting Solution To Go” Kit is composed of an Energy Micro Giant Gecko (Cortex M3) Starter Kit and an energy harvesting board that is capable of getting enough solar, thermal, piezoelectric or electromagnetic energy to power the MCU board. The power connector shown above connects directly to the Giant Gecko Starter Kit board to provide power. Although there are 4 energy harvesters on the board, only one power source can be selected at a time via jumpers. Several power sources can be selected by using diodes. The board The energy harvesting board offers two integrated energy sources: A solar cell (32mm x 50mm) A thermo-generator (40mm x 40mm). And 2 other external energy sources can be added to the board via […]

October 23, 2012July 31, 2022 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

Arduino Due Cortex M3 Board is now Available

Announced a little over a year ago, the Arduino (over) Due based on Atmel SAM3U Cortex M3 MCU is finally available for purchase. The specifications of the new boards are as follows: Microcontroller – Atmel AT91SAM3X8E @ 84 Mhz Flash Memory – 512 KB SRAM – 96 KB (64 + 32 KB) Operating Voltage – 3.3V Input Voltage (recommended) – 7-12V Input Voltage (min/max) – 6-20V Digital I/O Pins – 54 including 6 supporting PWM Analog Input Pins – 12 Analog Output Pins – 2 (DAC) Total DC Output Current on all I/O lines – 130 mA DC Current for 3.3V Pin – 800 mA DC Current for 5V Pin – Theoretical 1A, recommended 800 mA Debug ports – JTAG/SWD connector The new board is mostly compatible with the AVR (8-bit) boards, but since the board runs at 3.3V some shields may not be compatible (Arduino Wi-Fi and Ethernet shields do […]

September 19, 2012September 19, 2012 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

$25 Outbreak Galago – Cortex M3 Open Hardware Development Kit

Outbreak Galago is a tiny development kit based on a Cortex M3 processor that fits a debugger, and is destined for rapid electronics prototyping. The company promotes it as some sort of Arduino board on steroid (MCU wise) and sells for $25 on kickstarter, and less than $10 in 10k quantities. Here are the board specifications: 72 MHz 32-bit ARM CPU with 32KB of flash ROM and 8KB of RAM (NXP LPC1313 TBC) Integrated hardware debugger One high-speed SPI port, up to 36 Mbps One high-speed I2C port, up to 1.5 Mbps One UART/USART with hardware flow-control capability, up to 256 kbps 10 high-speed PWM pins, 6 driven by 32-bit (high-resolution) timers 6 ADC (analog) input pins with 10-bit resolution at over 400 KSa/sec 25 GPIO (digital) input/output pins The form factor and built-in debugger (via USB) are not really new, as those are already featured in devkit such as TI Piccolo controlSTICK, […]

August 28, 2012August 28, 2012 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Intel to Give Away 5 Atom D2700 Development Kits to Selected Engineers

As part of its “Eureka! Design Challenges“, Intel is asking hardware engineers to submit ideas about what they’ll do with an Intel Atom D2700 development kit with 2Gb RAM, a 40 GB SSD drive & lots of ports and expansions, and will give one to the 5 candidates with the best project ideas. Here are the key features of this development kit: Development board with the Intel Atom Processor D2700, and IntelNM10 Express Chipset Board Support package from the Linux Foundation’s Yocto Project 2GB DDR21066 MT/s non-ECC memory 40GB SSD, installed, with SATA extension cable Power supply The Intel Software Development Tool Suite (GNU tool compatible) Documentation and software Comes in a mini-ITX chassis with dual independent display capabilities. I’m not sure why Intel is focusing on hardware engineer for this type of project, and I suppose if you have some embedded systems development ideas that interface with external hardware, […]

August 13, 2012 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Exynos 4412 based Origen 4 Quad Development Board Soon Available for $199 USD

As I wrote a list of the Top 10 ARM Linux development boards, I discovered that Origen 4 Quad development board based on Exynos 4412 quad core Cortex A9 processor is currently in development and will replace the Origen board (Samsung Exynos 4212). This board appears to be similar to Hardkernel ODroid-X board, but pricing won’t be as aggressive as it will sell for $199 (vs $129 for the ODroid-X) in the base configuration. Here are the specifications for the base version (ORIGEN 4 Quad Package-C): CPU Board CPU : Samsung Exynos 4 Quad Cortex-A9 core 1.4 GHz DRAM : 1 GB (POP Type) PMIC : S5M8767A Base Board HDMI support Ethernet (10/100 Mbps), SDcard 2x USB 2.0 Host, 1x USB 2.0 Device Serial, JTAG Connector support (Sub Boards) External I/F MIPI CSI/DSI , Parallel, C2C Sub Boards Sound Board: Realtek : ALC-5631Q-A ORIGEN 4 Quad Package-B is based on […]

August 13, 2012August 13, 2012 by Jean-Luc Aufranc (CNXSoft) - No Comments

Over 20 Capes are Now Available for the Beaglebone

BeagleBoard.org has recently announced that over 20 plug-in boards (called Capes) are now available for the BeagleBone, an open hardware board powered by TI Sitara AM335x Cortex A8 processor. Capes allow to expand the abilities of the board via two 46-pin headers. Each cape has those 2 headers as well, and up to 4 capes can be stacked on a Beaglebone as long as the pins do not conflict… Here are some of the available capes: BeagleBone LCD7 Cape – Features a 7-inch TFT LCD screen with 4-wire resistive touch and five user buttons. BeagleBone Camera Cape – Allows you to add a camera via QuickLogic CSSP camera interface solution connected via the GPMC (General Purpose Memory Controller) bus of the Beaglebone. BeagleBone Weather Cape – Includes temperature, barometric pressure, humidity and ambient light sensors. BeagleBone DVI-D Cape – Provides a DVI-D interface, which can be handy since there is no […]

August 7, 2012 by Jean-Luc Aufranc (CNXSoft) - No Comments

Adafruit Launches Raspberry Pi Starter Pack for $69.95

The Raspberry Pi is supposed to be great for hardware prototyping, but you may not know where to start and/or depending where you live it might be difficult to buy the small components needed at a decent price. That’s where Adafruit Raspberry Pi starter pack comes into play. It includes a case, some cables and power supplies, as well as a breadboard and a whole bunch of components. The package includes: Adafruit clear acrylic Pi Box USB Micro-B Cable to connect the Raspberry Pi to a power source 5V 1A power adapter USB TTL console cable to be used to access the serial console. Useful to debug the kernel or if you run your device without display and/or network. 4GB SD Card Adafruit Pi Cobbler kit with GPIO cable for connection to the GPIO/I2C/SPI/Power pins. USB microSD card reader for loading the image onto the SD card. Large full-size clear […]

August 5, 2012August 6, 2012 by Jean-Luc Aufranc (CNXSoft) - 22 Comments

HardKernel ODroid-X Development Board Unboxing and First Boot to Android

I’ve just received the ODroid-X development board based on Samsung Exynos 4412 quad-core processor together with lots of accessories: WiFi-Modules Kit USB-UART Module Kit 16 GB eMMC Module 5V/2A Adaptor 10.1″ LCD Module (1366×768) BlueTooth Dongle Camera Module HDMI Cable Since there is quite a lot of things to cover, today I’ll just show some unboxing pictures, how to connect all those modules to the board and run Android pre-loaded in the eMMC module, and I’ll do a more detailed review with Android and Ubuntu in another post. I received the kit in a large box sent via EMS. Here’s a picture with the board and all accessories present in the Box. From top left to bottom right: 10.1″ LCD Modules, ODroid-X development board, HDMI to mini HDMI cable, micro USB to USB cable (for debugging), 5V/2A power supply for the board, 9V/1.5A power supply for the LCD module, WiFi […]