module News - Page 9 of 13 - CNX Software

December 6, 2021December 6, 2021 by Sponsored Post - 10 Comments

Ai Thinker enters the NB-IoT LPWAN market with EC-01 modules (Sponsored)

As we all know, 2G and 3G cellular networks are gradually being sunset, and NB-IoT has been formally incorporated into 3GPP standards. The LPWAN industry has ushered in new development opportunities for the Internet of Things market. Ai-Thinker has recently released three NB-IoT series modules: EC-01/EC-01F/EC-01G. The NB-IoT series modules are equipped with the EC616S chip platform, which is an ultra-low-cost, ultra-low power, ultra-high integration NB-IoT SOC chip, fully supporting the 3GPP R13/R14 NB-IoT standards with up to 159 kbps uplink. What are the benefits of the new modules? Better signal, more spectrum Better performance (equipped with EC616S) Ultra-low power consumption, stable and reliable connectivity I/O expansion, feature-rich module Check out the comparison table between AI Thinker NB-IoT modules part of the EC-01 family below. Ai-Thinker NB-IoT series modules adopt an SMD package that is convenient for mass production at the factory, and can use AOI to do the SMT […]

December 5, 2021 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Eigencomm EC616/EC616S SoC supports Cat-NB2 cellular IoT

Eigencomm EC616/EC616S are Cortex-M3 microcontrollers supporting the 3GPP R13/R14 NB-IoT standard, with 3GPP R14 notably introducing the newer LTE Cat-NB2 standard allowing higher bitrates up to 127 kbps downlink, and up to 159 kbps uplink, and OTDOA and E-CID positioning methods. Both EC616 and EC616S are virtually identical, but the EC616S comes with fewer GPIOs and is designed for the lowest possible BoM cost for modules as small as 10×10 mm. Both target similar IoT applications such as wireless meter reading, smoke detection, smart street lights, smart logistics, asset tracking, smart fire monitoring, smart parking, smart home, wearable devices, industry 4.0, smart agriculture, and others. Eigencomm EC616/EC616S specifications: MCU core – Arm Cortex-M3 @ up to 204 MHz Frequency band – 663 MHz to 2200 MHz Protocol version – 3GPP R13/R14 Built-in PA output power – 23dBm Receiver sensitivity – EC616: -118 dBm, EC616S: -117 dBm Peripherals EC616 – 2x […]

October 11, 2021February 18, 2022 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

RAK introduces Raspberry Pi RP2040 based LoRaWAN core, more Wisblock modules

RAKwireless has just launched the RAK11310 WisBlock LPWAN Module with Raspberry Pi RP2040 MCU and LoRaWAN connectivity, as announced after launching 14 new WisBlock modules for IoT prototyping last July. The RAK11310 module was introduced as part of the “Just Track It RAK Autumn Launch 2021” event together with the smallest WisBlock Base Board so far, as well as 11 new Wisblock modules which bring the total to 47 modules. RAK11310 – Raspberry Pi RP2040, LoRaWAN connectivity RAK11310 specifications: RAK11300 WisDuo LPWAN Module MCU – Raspberry Pi RP2040 dual-core Cortex-M0+ microcontroller @ 133MHz with 246 kB RAM LoRa connectivity SX1262 LoRa transceiver Worldwide frequency coverage RAK11310L – EU433, CN470 RAK11310 – EU868, US915, AU915, KR920, AS923, IN865, RU865 LoRaWAN 1.0.2 protocol stack (supports Class A & C) I/O ports – UART, I2C, GPIO, USB through a “Wisconnector” Debugging – Serial Wire Debug (SWD) interface Supply Voltage – 2.0 V ~ […]

September 9, 2021September 15, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

LILYGO T-32C3 – A small ESP32-C3 WiFi & BLE IoT module with 4MB flash

We’re slowly starting to see more hardware-based on ESP32-C3 RISC-V processor, and LILYGO T-32C3 is a compact module based on the WiFi & Bluetooth LE processor that includes 4MB flash and a PCB antenna. I’d expect T-32C3 to be eventually found in the company’s smartwatches and development boards, and it joins other ESP32-C3 modules from AI Thinker. LILYGO T-32C3 module specifications: SoC – Espressif ESP32-C3 RISC-V processor @ 160 MHz with 400 KB SRAM, 384 KB ROM, 8KB RTC SRAM, 2.4 GHz WiFi 4, Bluetooth 5.0 LE & Mesh Storage – 4MB flash On-board PCB antenna I/Os – 22x castellated holes with GPIO, 3x ADC, SPI, UART, I2C, Boot, Reset, 5V, 3.3V, GND Dimensions – 23 x 11 x 3.5 mm (4-layer PCB) Note the USB interface is not listed in the specs, but USB DN and DP signals are located on GPIO18 and GPIO19 so USB should also be […]

September 3, 2021October 8, 2021 by Jean-Luc Aufranc (CNXSoft) - 11 Comments

M5Stamp Pico ESP32-PICO-D4 module ships with a heat-resistant plastic shell

Most WiFi IoT modules are designed to be integrated into products with an enclosure, but the M5Stamp Pico module based on ESP32-PICO-D4 SiP comes with a removable heat-resistant plastic shell that protects the 3D antenna and components, while leaving space to solder headers and/or a Grove connector. The tiny module also comes with a button and RGB LED, and like other ESP32-based M5Stack hardware, M5Stamp Pico is programmable with UIFlow graphical programming platform and compatible with Arduino, MicroPython, and the ESP-IDF. M5Stamp Pico specifications: System-in-Package – Espressif Systems ESP32-PICO-D4 SiP with dual-core processor @ 240MHz, 520KB SRAM, 4MB flash, and 2.4 GHz Wi-Fi 4 up to 150 Mbps and Bluetooth 4.2 BR/LE connectivity Antenna – 2.4 GHz 3D antenna I/Os – 2.54mm pitch header with ADC, DAC, touch sensor, SD/SDIO/MMC host controller, SPI, SDIO/SPI slave controller, EMAC, PWM, UART, I2C, I2S, IR remote controller, up to 12x GPIO, pulse counter […]

August 24, 2021September 2, 2021 by Jean-Luc Aufranc (CNXSoft) - 36 Comments

Coin cell-powered OpenThread sensor board can send data every 20 seconds for three years

Monkey Store’s Thread Sensor Tag is a pressure, humidity, temperature, and light sensor that connects to the OpenThread network, and is capable of transmitting MQTT/UDP data every 20 seconds over a period of around three years from a single coin cell battery. As a reminder, OpenThread is an implementation of the Thread IoT network protocol that was unveiled in 2016 by Nest Labs (now Google/Alphabet). This has not been widely used so far, but we did write about MKR SharkyPro development board with OpenThread support via STMicro STM32WB5MMG wireless module earlier this year, and Monkey Store is telling us both Google and Apple are working on devices with support for the IoT protocol. Thread Sensor Tag specifications: Wireless module – Minew MS88SF2 based on Nordic Semi nRF52840 multi-protocol 2.4GHz wireless Cortex-M4 microcontroller Sensor VEMLS6030 I2C light sensor MS8607 pressure, humidity, and temperature sensor I/Os – 7x through holes with Tx/Rx, […]

August 17, 2021August 17, 2021 by Jean-Luc Aufranc (CNXSoft) - 11 Comments

Offline speech recognition MCU module comes with speaker, microphone, and UART connectors

We found out about Unisound US516P6 RISC microcontroller inside an offline voice assistant module last May. The module offers offline speech recognition for just $2 to $4, with good performance, and excellent privacy since no cloud service nor Internet connection is needed. That module requires some soldering, but if you’d prefer something easier to connect the “SU-10A” offline speech recognition MCU module comes with connectors for a speaker, a microphone, as well as UART connectivity to a host MCU if needed. “SU-10A” module specifications: MCU – Unisound US516P6 RISC microcontroller @ 240 MHz with FPU, DSP instruction, FFT accelerator, 242KB SRAM, 2MB flash Audio Built-in 3W mono Class AB power amplifier. 2mm pitch connector for speaker (4 Ohms up to 2.9W, 8 Ohms up to 1.8W) 2mm pitch connector for electret microphone Debugging/programming – UART port for serial console (5V or 3.3V supported) Host interface – 2mm pitch 4-pin connector […]

August 5, 2021September 26, 2021 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

BL-63B – A smaller BL602 IoT module that sells for $1.5

Bouffalo Labs BL602 is a low-cost, low-power RISC-V microcontroller that offers 2.4 GHz WiFi and Bluetooth 5.0 LE connectivity for IoT projects for about the price of ESP8266. We first discovered it last year, together with a development board. Pine64 created its own PineCone board fitted with the $2 PineNut module, and some reverse-engineering work has started on BL602 SDK. But there’s now another smaller BL602 module with “Machine Intelligence” (that’s the company name) BL-63B that sells for $1.5 on Taobao in China, as well as on LCSC Electronics albeit you’d need to purchase 1000 pieces to get that price, and single-unit pricing is currently $2.5. BL-63B WiFI & BLE module specifications: SoC – Bouffalo Labs BL602 32-bit RISC-V processor @ up to 192 Mhz with 276KB RAM, 128KB ROM, 1Kbit eFuse, WiFi and BLE Storage – 2MB flash Wireless 2.4GHz 802.11b/g/n WiFI 4 1×1 SISO up to 65 Mbps […]