robotics

Posted on by Jean-Luc Aufranc (CNXSoft) - 4 Comments on $199 Gizmo 2 Development Board Powered by AMD G-Series GX210HA SoC

$199 Gizmo 2 Development Board Powered by AMD G-Series GX210HA SoC

There are only a few Intel / AMD x86 embedded development boards on the market, at least for the hobbyist market, namely MinnowBoard MAX based on Intel E3815 or E3825 processors, and Gizmophere Explorer Kit powered by AMD G-Series GT-40E dual core APU + A55E hub controller. Gizmosphere, a non-profit organization, had now released a new version of their embedded board called Gizmo 2 powered by AMD G-Series GX210HA SoC combining a dual core x86 processor, a Radeon GPU, and peripherals. Gizmo 2 development board specifications: SoC –  AMD Embedded G-Series GX210HA SOC with a dual core “Jaguar” processor @ 1.0 GHz and a Radeon 8210E GPU @ 300 MHz with support for DirectX 11.1, OpenGL 4.2x and OpenCL 1.2. 153 GFLOPS of performance. 9W TDP. System Memory – 1GB DDR3-1600 SDRAM Storage – mSATA/mini PCIe Connector + micro SD card slot Video Output – HDMI Audio I/O – HDMI and […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 2 Comments on Robotics News – Hack-E-Bot and RiQ Educational Robots, and Maker Club 3D Printed Robots (Pre-Orders / Crowfunding)

Robotics News – Hack-E-Bot and RiQ Educational Robots, and Maker Club 3D Printed Robots (Pre-Orders / Crowfunding)

I’ve come across several robotic projects this week, so instead of picking one up, or writing a post for each, I’ll summarize the three products into one post. Two of the projects are educational robots based on Arduino, with the sub $50 Hack-E-Bot, or the more advanced RiQ robot, and Maker Club is a company providing the electronics for robotics kit, and you print the plastic parts with your 3D printer. Hack-E-Bot Robot Hack-E-Bot is an affordable open source robot that hopes to encourage children to learn about engineering, electronics, and programming. The robot is powered by Adafruit’s Trinklet Arduino compatible board, connected to a breadboard, and some add-on boards sensors. The basic version comes with a Sonar sensor, but more add-on boards are on the way including bump sensors, a buzzer, colored lights, a claw, a servo scanner, and so on. The project is listed on CrowdSupply, and has […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 1 Comment on RPiSoC Development Board Based on Cypress PSoC 5LP Features Pmod, Raspberry Pi, and Arduino Headers (Crowdfunding)

RPiSoC Development Board Based on Cypress PSoC 5LP Features Pmod, Raspberry Pi, and Arduino Headers (Crowdfunding)

Embedit Electronics, a startup founded by two recent graduates of Rensselaer Polytechnic Institute, USA, has designed a board powered by Cypress Semiconductor PSoC 5LP ARM Cortex M3 system-on-chip with programmable digital and analog I/Os. The board can interface with all Raspberry Pi models, Digilent Pmod peripheral modules, and supports Arduino shields. RPiSoC specifications: SoC – Cypress PSoC 5 with ARM Cortex M3 core at 67MHz , 256 KB Flash Program Memory, with user configurable write protection, and 64KB SRAM Expansions and I/Os: Arduino shield and ICSP compatible headers. 2x Digilent Pmod compatible headers 58 reconfigurable GPIO pins 26-pin ribbon cable connector for use with the Raspberry Pi 8 SIO (Special Input/Output) pins with higher current sink 5-pin MiniProg3 header for programming via MiniProg3 hardware. USB – 1x micro USB port for power, communication and programming. Misc – Reset push button, User accessible LED, Programming switch Power – 5V via micro […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 12 Comments on WRTNode is a Hacker-Friendly Open Source Hardware OpenWRT Wi-Fi Module Selling for $25

WRTNode is a Hacker-Friendly Open Source Hardware OpenWRT Wi-Fi Module Selling for $25

There are now some tiny and low cost ($15 to $20) Wi-Fi modules supporting OpenWRT such as VoCore and AsiaRF AWM002. However due to their small size they may not be that hacker’s friendly as they can’t have 2.54mm headers due to heir small size, and I’ve recently received AsiaRF AWM002 only to find out it not only needs 3.3V supply voltage, but also 1.8V and 1.2V. So I’d need to make my own power circuit with the required LDOs, or purchase a $20 base board to use the module. Here comes WRTnode another larger Wi-Fi module but with more usable 2.54mm headers, and based on the more powerful Mediatek MT7620N processor @ 600MHz. WRTnode hardware specifications: Processor – Mediatek  MT7620N 600MHz MIPS CPU (MIPS24KEc) System Memory – 64MB DDR2 Storage – 16MB SPI flash Connectivity – Wi-Fi 2T2R 802.11n 2.4 GHz up to 300Mbps Expansion Headers – 2x with […]