Operating Systems Category - Page 385 of 1033 - CNX Software

May 15, 2019 by Jean-Luc Aufranc (CNXSoft) - 10 Comments

Atomic Pi SBC is back with pre-orders on Amazon and Ameridroid

Atomic Pi single board board is probably the SBC with the best performance / value ratio on the market, so when we reported that Atomic Pi was available worldwide last month the 6,000 pieces available quickly ran out of stock. Many people suspect it was a limited product run from a previous project, and indeed Atomic Pi is most likely AAEON MF-001 board that was designed for Kuri robot designed for the now-defunct Mayfield Robotics. But we have some good news as Atomic Pi SBC does not appear to be a one-off sales getting rid of stock as it’s now back for pre-order on Amazon US and Ameridroid with shipping scheduled for the end of May. I won’t go through the whole specifications again but with an Intel Atom x5-Z8350 quad core processor, 2GB RAM, and 16GB flash, Atomic Pi board has hardware far more powerful than the similarly priced […]

May 14, 2019February 16, 2020 by Jean-Luc Aufranc (CNXSoft) - No Comments

BB-400 Neuron Edge Dual Ethernet Industrial Controller Combines Raspberry Pi CM3+ and Arduino MCU

bb-400 neuron edge industrial controller

While the Raspberry Pi boards are mostly promoted as tools to teach STEM to kids and adults alike, they have found their way in a fair amount of industrial products, including ModBerry M500 industrial computer, Janz Tec emPC-A/RPI3 industrial embedded controller, and Kunbus RevolutionPi RevPi Core among others. There’s yet another option with Brainboxes BB-400 Neuron Edge industrial controller that was announced last year with Raspberry Pi Compute Module 3, but recently got an upgrade to Raspberry Pi Compute Module 3+. The controller features two Ethernet ports and also includes an Arduino compatible microcontroller to control the system’s eight configurable digital inputs and outputs. BB-400 Neuron Edge industrial controller specifications: SoM – Raspberry Pi Compute Module 3+ with Broadcom BCM2837B0 quad-core , Cortex-A53 processor @ 1.2GHz, 1 GB LPDDR2, 32GB eMMC Flash storage MCU – Unnamed Microchip Atmel Arduino compatible microcontroller Connectivity Ethernet Uplink Port – 1x RJ45 jack, 10/100Mbps […]

May 14, 2019May 14, 2019 by Jean-Luc Aufranc (CNXSoft) - 29 Comments

Khadas VIM3 Amlogic S922X Board to Support M.2 NVMe SSD, WiFi 5, and Bluetooth 5 Connectivity

Ever since the Amlogic S922X powered ODROID-N2 SBC launched last March, I keep reading praise for the processor and board which both deliver great performance at a relatively low price. Hardkernel was the only company that sold such a board so far, but this is about to change with some competition coming from Shenzhen Wesion with their upcoming Khadas VIM3 board that includes 2 to 4GB RAM, 16 to 32GB eMMC flash storage, a wireless module, support for M.2 NVMe SSD, and more. Even though more are planned in the future, two Khadas VIM3 models have been announced so far – Basic and Pro – with the following preliminary specifications: SoC – Amlogic S922X hexa-core processor with 4x Arm Cortex-A73 and 2x Cortex A53 cores, Arm Mali-G52 MP4 GPU, built-in Cortex-M4 core for “always-on” processing MCU – STMicro STM8S003 with Programmable EEPROM for power management, customizations, and boot media configuration […]

May 13, 2019 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

e.Foundation to Sell Refurbished Phones Running Google-Free /e/ Android OS

Most Android phones come with Google services, which is both a boon and a curse, as those services are often convenient, but they come at the loss of your privacy. For example, most people get all upset and lost if a firmware image for an SBC is shipped without Google Play Store, but yet at the same time they worry about their privacy providing all their data to a single company like Google. There must be a better way, and that’s what the e.foundation is attempting with /e/ operating system based on Android, but without any of the Google Services, and targetting your typical end-users, as opposed to geek. /e/ operating system aims to provide privacy both inside the phone, and via cloud services unrelated to Google. It is a fork of LineageOS 14.1 itself a fork of AOSP, and replaces Google services and apps with programs such as MicroG […]

May 13, 2019May 14, 2019 by Jean-Luc Aufranc (CNXSoft) - 34 Comments

How One Line of Code Tripled Allwinner A20 SATA Write Performance

If you’ve been following this blog long enough, you may remember that all linux-sunxi community work aiming at improving u-boot and Linux software support on Allwinner processors started with Allwinner A10 processor found in MeLE A1000 TV box back in 2012, which at the time provided an interesting alternative to Raspberry Pi board that was in short supply at launch time and several months after. One of the most interesting feature found in Allwinner A10 single core Arm Cortex-A8 processor was its SATA interface, and Allwinner A20 was announced a few months later with a dual core Cortex-A7 processor and virtually the same peripherals as Allwinner A10, including SATA. However when I tested CubieTruck board connected to a mechanical drive, I noticed sequential SATA performance was fine for reads (~180MB/s), but writes were fairly slow at around 36 MB/s. Other people complained about it, and some looked into it, and […]

May 12, 2019May 13, 2019 by Jean-Luc Aufranc (CNXSoft) - 20 Comments

Low Power TinyPICO ESP32 Board Ships with Micropython (Crowdfunding)

There are so many ESP32 boards available now, so why bother with another ones. Some of the key selling points of TinyPICO are that it is really small at 32 x 18 mm, it’s easy to use out of the box with MicroPython firmware pre-loaded, and supports LiPo batteries with an optimized power path for low-power battery usage. The developer, named Unexpected Maker, also provides various shields for TinyPICO adding a display, sensors, an audio amplifier, an RTC, Grove headers, and more. TinyPICO board specifications: System-in-Package – Espressif Systems ESP32-PICO-D4 SiP with ESP32 dual-core processor operating at 240 MHz, 4 MB SPI flash External System Memory – 4 MB PSRAM Connectivity – 2.4 GHz WiFi 4 802.11b/g/n, Bluetooth 4.2 LE, 3D antenna Expansion – 14x GPIO broken out to standard pitch headers Debugging / Programming – USB + serial/UART for programming Misc – Power (red) & charge (orange) LED’s, APA102 […]

May 11, 2019May 12, 2019 by Jean-Luc Aufranc (CNXSoft) - 8 Comments

Volumio Motivo is a Gorgeous Audio Streamer Powered by SOPINE A64 SoM

Volumio is a well-known Linux based open source music player for Raspberry Pi, UDOO, Cubox-I, Beaglebone Black, and other single board computers. Some companies even made audiophile boards with support for Volumio including Khadas Tone high-resolution audio board for VIM/VIM2 SBC’s, and the tiny VoltaStream ZERO following Raspberry Pi Zero form factor. But Volumio team has decided to make their own hardware with Motivo, an awesomely looking audio streamer designed in collaboration with Yottamusic engineering firm, and Design Narratives industrial design company. Motivo was introduced at High-End Munich, the world’s biggest Hi-Fi trade fair, and Pine64 posted some photos in a tweet claiming it was powered by their SOPINE A64 system-on-module. The full details about the device have not been published at the time of writing, but we can still derive some of Volumio Motivo specifications and key features from the photos and a few bits of public information: System-on-Module […]

May 10, 2019May 10, 2019 by Jean-Luc Aufranc (CNXSoft) - No Comments

Gateworks Introduces GW16126 Mini-PCIe Cat M1 Modem and Bluetooth LE Radio

Gateworks has launched another mini PCIe card providing IoT connectivity for their NXP i.MX 6 and Cavium Octeon TX powered SBC’s. Last month we covered GW16130 Mini PCIe satellite modem, and the company has now announced GW16126 mini PCIe card with a Cat M1 (eMTC) modem and a Bluetooth Low Energy radio for the US market, and other regions or countries where LTE Cat M1 networks have been deployed. Gateworks GW16126 mini PCIe card specifications: LTE Cat M1 Module – U-blox SARA-R410M-52 LTE CAT M1 cellular modem with up to 375 kb/s upload and 300 kb/s download; LTE Bands 2,4,5,12,13 SIM card – nano-SIM socket with hologram starter SIM included with free 1MB/month starter plan included BLE module – u-blox NINA-B301 Open CPU Bluetooth 5.0 Low Energy Radio based on Nordic Semiconductor nRF52840 chipset, Zephyr RTOS with Bluetooth HCI UART Host Interface. BLE Rates up to 2Mbps Antennas – 2x […]