Category: Texas Instruments Sitara

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on Embest SBC8118 Single Board Computer Based on TI AM1808 Processor

Embest SBC8118 Single Board Computer Based on TI AM1808 Processor

Embest recently unveiled the SBC8118 Single Board Computer, an industrial grade SBC powered by Texas Instruments AM1808 ARM9 processor with 128MB Mobile DDR2 RAM and 128MB NAND Flash. The SBC8118 Single Board Computer is aimed at medical, industrial automation, control, communication, and other cost sensitive applications. As you can see from the picture above, it is comprised of a CPU board and an expansion board. Here are the specifications of the CPU board (Mini8118): Processor – 375MHz TI AM1808 ARM926EJ-S Microcontroller (also supports 456MHz operation) Memory – 128 MByte Mobile DDR2 Storage – 128 MByte NAND Flash (on the rear of the board) & 8 Mbit SPI Flash Connectors – Two 2.0mm space 3*27-pin dip connectors and the expansion board: Audio/Video Interfaces: TFT LCD interface (50-pin FPC connector, RGB565) 4 line resistive Touch Screen interface Camera interface (30-pin FPC connector, supports CCD and CMOS cameras) Data Transfer Interfaces: Serial port: […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 3 Comments on Rowboat Releases Android 4.1.1 Jelly Bean for Beagleboard-XM and Beaglebone

Rowboat Releases Android 4.1.1 Jelly Bean for Beagleboard-XM and Beaglebone

Rowboat announced a preliminary version of Android 4.1.1 (Jean Bean) for beagleboard and beaglebone platforms last week. These releases support SGX (3D graphics acceleration) on both Texas Instruments Sitara AM37x processor (Beagleboard-XM) and  AM335x processor (Beaglebone), and all download and build instructions are available on their Wiki: Jellybean On Beagleboard JellybeanOn Beaglebone – Tested with LCD7 cape. If you could not care less about building it yourself, Rowboat provides pre-built binaries that you can install on a micro-SD card (4GB and greater) as follows : For Beagleboard-XM (DVI output):

For Beaglebone (with 7″ LCD Cape):

The full source is available on rowboat gitorious  account, but there are lots of repo over there, so the best way to get the source is probably the “repo init” instructions in the 2 links above. Jean-Luc Aufranc (CNXSoft)Jean-Luc started CNX Software in 2010 as a part-time endeavor, before quitting his job as […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 2 Comments on Timesys Unveils LinuxLink BSP/SDK for MityARM-3359 SoM (TI AM335x)

Timesys Unveils LinuxLink BSP/SDK for MityARM-3359 SoM (TI AM335x)

Critical Link is an electronics product development company that provides “MityDSP” and “MityARM” System on Modules and Timesys is a software company working on Embedded Linux, which provides LinuxLink, a software development framework for embedded Linux application development. Both companies have partnered to offers LinuxLink BSP/SDK for MityARM-3359 SoM based on Texas Instruments Sitara AM335x Cortex A9 processor. LinuxLink (for MityARM-335x) comes in 2 versions: A free version which includes: A wizard-based interface that simplifies the selection of a Linux kernel, software packages and tools Kernel, toolchain and debugger Access to hundreds of open-source software packages Support by Timesys for build/boot issues. A PRO version (Starts at $5495 per developer) which includes extra “features” such as: TimeStorm IDE – A desktop-based development environment Tools for advanced customization and integration unmetered support Everything is built on Timesys servers, but the web interface makes it quite customizable and offers lots of options […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 3 Comments on ISEE Announces Low Cost IGEP COM ELECTRON & SPIN Computers-on-Module

ISEE Announces Low Cost IGEP COM ELECTRON & SPIN Computers-on-Module

ISEE, the manufacturer of the IGEPv2 board, has recently announced 2 new industrial grade computers on module based on TI Sitara AM3703 Cortex A8 Processor: IGEP COM ELECTRON – AM3703 with 256 MB RAM / 512 MB Flash – 59 Euros IGEP COM SPIN – AM3703 with 64 MB RAM / 128 MB Flash – 49 Euros Here are the specifications of IGEP COM ELECTRON module: CPU – Texas Instruments AM3703 @ 1GHz with L1 cache (112 KB (DSP) / 64 KB (ARM)) and L2 cache (96 KB (DSP), 256 KB (ARM)) System Memory – 256 MB Mobile DDR @ 200 MHz (32-bit) Storage: 512 MB NAND FLASH On board micro-SD socket Connectors: 1 x USB 2.0 OTG interface + USB mini-AB connector 1 x MICRO-SD socket 2 x EXPANSION 70-pin connector Device: 1 x USB 2.0 HOST (connector NOT included) 1 x DOUBLE LED INDICATOR Expansion connectors – 2 […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on Over 20 Capes are Now Available for the Beaglebone

Over 20 Capes are Now Available for the Beaglebone

BeagleBoard.org has recently announced that over 20 plug-in boards (called Capes) are now available for the BeagleBone, an open hardware board powered by TI Sitara AM335x Cortex A8 processor. Capes allow to expand the abilities of the board via two 46-pin headers. Each cape has those 2 headers as well, and up to 4 capes can be stacked on a Beaglebone as long as the pins do not conflict… Here are some of the available capes: BeagleBone LCD7 Cape – Features a 7-inch TFT LCD screen with 4-wire resistive touch and five user buttons. BeagleBone Camera Cape – Allows you to add a camera via QuickLogic CSSP camera interface solution connected via the GPMC (General Purpose Memory Controller) bus of the Beaglebone. BeagleBone Weather Cape – Includes temperature, barometric pressure, humidity and ambient light sensors. BeagleBone DVI-D Cape – Provides a DVI-D interface, which can be handy since there is no […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on $39 Variscite VAR-SOM-AM33 SoM Powered by TI Sitara AM335x

$39 Variscite VAR-SOM-AM33 SoM Powered by TI Sitara AM335x

Variscite has announced a new system-on-module based on Texas Instruments Sitara Cortex A8 AM335x processors (AM3352 or AM3354) named VAR-SOM-AM33, which sells for as little as $39 US (in large quantities I assume). This SoM is available in commercial and industrial grades, and the company expects the module to be used in applications such as automotive, control systems, lighting, refining and processing. Here are the specs of this module: CPU – Texas Instruments AM335x Processor @ up to 720 MHz withPowerVR SGX530 GPU (AM3354 only) System Memory – 256MB 606MHz DDR3 Storage – 128 to 512MB SLC NAND Flash Display interface – LCD interface – Parallel RGB Supporting 1400×1050 24bit and4/5/8-Wire touch panel interface Audio – Line-in, line-out, stereo headphone out, digital microphone, analog microphone and S/PDIF Out Connectivity: 10/100Mbps Ethernet PHY 10/100/1000Mbps RGMII Wi-Fi 802.11 b/g/n (via TI WiLink 6.0) Bluetooth V4.0 + EDR (via TI WiLink 6.0) Interfaces: 2 […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 6 Comments on Gumstix Waysmall Silverlode Linaro Ubuntu Computer based on TI Sitara AM3703

Gumstix Waysmall Silverlode Linaro Ubuntu Computer based on TI Sitara AM3703

Gumstix has just announced the Waysmall Silverlode computer, a small form factor device running Linaro ARM optimized Ubuntu and designed for developers of commercial and industrial applications such as digital signage players and remote servers. It’s based on Overo EarthSTORM Computer-on-Module (Texas Instruments Sitara AM3703 @ 1 GHz, 512MB Flash and 512MB RAM) and consumes less than 2.5 W. Here are the specs of the device: Processor Texas Instruments Sitara AM3703 processor (ARM Cortex-A8 ) @ 1 GHz 800 MHz is recommended for reliable performance System Memory 512 MB RAM Storage 512 MB NAND flash microSD card slot Video Output HDMI (DVI-D) Audio I/O Stereo Audio In /Out jacks Connectivity 10/100Mb Ethernet USB USB Host, USB OTG and USB Console Connectors 2 x 70-pin AVX connectors 1 x 27-pin Hirose camera connector Battery holder for 6mm rechargeable coin Dimensions 11.0 x 4 .4 x 1.8 cm Power 5V The computer […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on Gumstix TurtleCore Expansion Board for iRobot Create

Gumstix TurtleCore Expansion Board for iRobot Create

Last month, Gumstix announced the TurtleCore expansion board for iRobot Create Programmable Robot, featuring 3 USB ports, several male-header pins with GPIO access, as well as standoffs and screws to support the TurtleCore in the Create cargo bay.. The TurtleCore is a baseboard for TI OMAP3 and Sitara based Overo COMs or Overo STORM series of COMs that replaces the Command Module on iRobot Create to provide a more flexible and powerful solution. Overo COMs have very good Linux support (OpenEmbedded) with source code, tools and documentation available, including support for the Robot Operating System (GumROS) for high level programming. They released the hardware early so that the community could work on the software, and there have been some good progress as you can see from the video below. You can already download the schematics and PCB layout file, but the software and instructions do not appear to be available […]