digital signage News - Page 18 of 28 - CNX Software

March 31, 2017March 31, 2017 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

MQMaker Koala is a Features-Packed Development Board Powered by Rockchip RK3288 Processor

MQMaker launched MiQi board based on Rockchip RK3288 quad core Cortex A17 processor last year with the hardware aimed at hobbyists and makers, but the company has been developing a higher-end board – named Koala – based on the same processor, featuring many more ports and features, and geared towards the enterprise market. Koala board preliminary specifications: SoC – Rockchip 3288 quad core ARM Cortex A17 up to 1.8 GHz with Mali-T764 GPU supporting OpenGL ES 1.1/2.0 /3.0, and OpenCL 1.1 System Memory – 2GB DDR3 (default) Storage – 16 GB eMMC flash (default) + micro SD slot Video Output / Display Interface – HDMI 2.0, header for eDP, MIPI, LVDS, LCD backlight header, touch panel header Audio – HDMI out, optical S/PDIF, 3.5mm analog stereo audio jack, microphone header, audio L/R header Connectivity – Gigabit Ethernet, WiFi or WiFi + Bluetooth module, mini PCIe slot for 3G/4G card + SIM card slot USB – 4x […]

March 29, 2017 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

VIA VTS-8589 OPS Board Powered by NXP i.MX 6 ARM Processor Complies with Intel’s OPS Digital Signage Specifications

Intel introduced the Open Pluggable Specifications (OPS) defining mechanical and electrical requirements for boards used in digital signage back in 2010. Since then there has been a few Intel OPS boards launched on the market, and the company introduced OPS+ specifications with support for simultaneous display and broadcast usages, 8K resolution displays, and the ability to drive three individual 4K resolution display outputs. VIA has now launched VTS-8589 OPS board compliant with the older specifications, and featuring NXP i.MX6 quad core ARM Cortex A9 processor combined with 2GB RAM, 8GB flash, and more. VIA VTS-8589 OPS has two version of the board with the following specifications: SoC VTS-8589-QP model – NXP i.MX 6QuadPlus quad ARM Cortex-A9 processor @ 1.0 GHz with Vivante GC2000+ GPU supporting OpenGL ES 3.0, OpenCL and OpenVG 1.1, 512KB embedded SRAM VTS-8589 model – NXP i.MX 6Quad quad ARM Cortex-A9 processor @ 1.0 GHz with Vivante GC2000 […]

March 17, 2017March 17, 2017 by Jean-Luc Aufranc (CNXSoft) - No Comments

Dell Edge Gateway 3000 Series Are Powered by Intel Bay Trail-I SoCs for Automation, Transportation, and Digital Signage

Dell has recently introduced Edge Gateway 3000 series with three models powered by Intel Bay Trail-I processor, running Ubuntu Core 16 or Windows 10 IoT, with each model targeting respectively general-purpose automation, transportation & logistics, and digital signage and retail. The specifications for the three models can be found in the table below. Dell Edge Gateway 3001 Model for General-Purpose Automation Dell Edge Gateway 3002 Model for Transportation & Logistics Dell Edge Gateway 3003 Model for Media & Retail Kiosks SoC Intel Atom E3805 dual core processor @ 1.33 GHz (3W TDP) Intel Atom E3815 single core processor @ 1.46 GHz with GPU @ 400 MHz (5W TDP) System Memory 2 GB DDR3L-1066 Storage 8 or 32 GB eMMC flash Industrial-grade Micro-SD card: 8GB / 16GB / 32 GB / 64 GB Connectivity 1 x 10/100 Fast Ethernet (RJ-45) with PoE (15.4W) WiFi 802.11 b/g/n Bluetooth 4.0 LE Optional ZigBee […]

December 22, 2016December 22, 2016 by Jean-Luc Aufranc (CNXSoft) - No Comments

Giada F105D Apollo Lake Mini PC Supports up to 3 Displays via HDMI 2.0, DisplayPort, and VGA Ports

Giada F105D is an upcoming mini PC powered by either a Celeron N3350 dual core or N3450 quad core processor part of Apollo Lake family with up to 4GB RAM, a 2.5″ SATA bay, and three video outputs: HDMI 2.0, DisplayPort and VGA. Except for the processor, F105D-BS200 and F105D-BQ200 mini PCs have the same specifications: SoC F105D-BS200 – Intel Celeron N3350 dual core processor @ 1.1 / 2.4 GHz with 12EU Intel HD 500 graphics (6W TDP) F105D-BQ200 – Intel Celeron N3450 quad core processor @ 1.1 / 2.2 GHz with 12EU Intel HD 500 graphics (6W TDP) System Memory – Up to 4GB DDR3L-1600MHz with 2GB on-board + 2GB on 204-pin SO-DIMM socket Storage – 1x 2.5″ SATA drive bay (max. height 7.5mm), 1x M.2 (PCIe), 1x mSATA III, 1x micro SD slot Video Output VGA up to 2560×1600 @ 60Hz, 24bpp HDMI 2.0 up to 3840×2160 @ […]

November 29, 2016November 30, 2016 by Jean-Luc Aufranc (CNXSoft) - 10 Comments

Grid-EYE Breakout Board is a $49 Low Resolution Thermal Camera Module

Thermal cameras can be really expensive pieces of equipment, and even the cheap 60×60 thermal cameras available on Aliexpress costs a little over $200. However, PURE Engineering has made an breakout board with Panasonic Grid-EYE infrared 8×8 array sensor that allows you to experiment with the technology, or integrate into your own projects for just $49. Grid-EYE breakout board features: Panasonic Grid-EYE AMG8834 64 pixel infrared / thermal camera sensor with 60 degree viewing angle using MEMS thermopile technology Pinout compatible with Arduino Zero, ST-NUCLEO board, and other 3.3V boards with I2C, VDD, GND, INT, and AD pins PUREModules PCB edge connectors with UART, GPIO, to interface with the company’s IoT board Power Supply – On-board regulator handles 3 to 5V input The Panasonic sensor transfers thermal presence, direction, and temperature values over I2C. The company wrote a demo for the module with an Arduino sketech and a Processing sketch […]

November 23, 2016November 25, 2016 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Zidoo Releases Digital Signage SDK for X8 and X9S Android TV Boxes

Zidoo X9S and X8 are Android 6.0 + OpenWrt TV boxes powered by Realtek RTD1295 processor with HDMI input supporting PIP, UDP broadcasting and video recording, which works reasonably well despite some 4K video decoding limitations. The company has now released a “digital signage SDK” – which I’d rather just call a digital signage demo – working on either device on github, but you can still study the source code in order to build your own. Some of the possible features showcased in the demo include: Digital Signage (AD) player as shown above with video, picture and scrolling text Multi Views display (HDMI IN + Video playing + Web browsing) Multi Videos decode Screen rotation Screen zoom in / out Display output resolution switch HDMI IN player HDMI IN picture in picture (PIP) So it’s not a total solution, just an “SDK” showing what can be done with media files, and you’d still have to write your own app managing content updates (from storage or network), as well as some content management software. Two apks are used: […]

October 14, 2016October 16, 2016 by Jean-Luc Aufranc (CNXSoft) - 39 Comments

Raspberry Pi Compute Module 3 to be launched by the end of the year, used in NEC displays

Eben Upton had already mentioned the Raspberry Pi Foundation was working on a Raspberry Pi Compute Module 3 based on the same Broadcom BCM2837 quad core Cortex A53 processor and 1GB LPDDR2 RAM used in Raspberry Pi 3 board earlier this year, but few details had been provided at the time. The module is still not available, but NEC Display Solutions Europe has already announced they are working on integrating Compute Module 3 into commercial displays starting with 40″, 48″ and 55″ models in January 2017, and up to 98″ by the end of next year, used for digital signage and presentation platforms. The Raspberry Pi Foundation goes on to say they’ve been working on NEC project for over a year now, and they expect to release Compute Module 3 to the general public by the end of the year. Price and complete technical details have not been released yet. […]

August 2, 2016August 11, 2021 by Jean-Luc Aufranc (CNXSoft) - 23 Comments

How to Set an Android TV Box Video Output to Portrait Mode

Most buyers who buy an Android TV box just want to use it to watch videos, browse the web, play games, and so on, so landscape mode seems to be the best choice, and the orientation option in the firmware is often disabled. However, TV boxes can also potentially be used as digital signage players, which may require landscape or portrait modes if the screen is positioned vertically. Since I’ve just been asked that question, I’ve checked for a solution, and luckily there’s an app called Set Orientation that does the job. [Update August 2021: The app has been removed from the Google Play store, it might be worth trying Screen Rotation Control app instead] When you first start the app, it will show the option “Disabled”, but you can click on the arrow to reveal more options, and select Portrait to rotate the screen. In case the screen is […]