ethernet News - Page 5 of 17 - CNX Software

January 22, 2022January 23, 2023 by Jean-Luc Aufranc (CNXSoft) - 14 Comments

Radxa E25 carrier board, 2.5GbE switch, and WiFi 6 router

Radxa E25 2.5GbE switch-Xiaomi AX6000 WiFi 6 router

I’ve just received an early sample of Radxa E25 dual 2.5 GbE carrier board for Radxa CM3 Plus (RK3568) system-on-module, a 2.5GbE TP-Link switch, and Xiaomi AX6000 WiFi 6 + 2.5GbE router. Here’s the back story before looking into the devices. I’ll soon have to review UP Xtreme i11 mini PC with a 2.5GbE port, and after writing about the upcoming ROCK5 Model B SBC with both 2.5GbE and WiFI 6/6E, I realized I should really get some hardware to test 2.5GHz and WiFi 6. So I started to ask what could be the best options for a $200 budget. While thinking about it, I remember Radxa was working on the Radxa E23 board with 2.5GbE, and adding a WiFi 6 USB dongle might be an option. But they told me Radxa E25 would be a better option with two 2.5GbE ports and support for WiFi 6, although that one […]

January 21, 2022April 27, 2023 by Jean-Luc Aufranc (CNXSoft) - 11 Comments

WCH CH32V307 RISC-V development board features 8 UART ports controlled over Ethernet

CH32V307 RISC-V development board 8x UART

CH32V307V-EVT-R1 is a development board based on WCH CH32V307 RISC-V microcontroller with an Ethernet port, an USB Type-C port, and eight UART interfaces accessible through headers. As we noted in our article about CH583 Bluetooth 5.3 RISC-V microcontroller, WCH (Jiangsu Qin Heng) has started to share resources like datasheets and code samples through Github. They’ve done the same again for CH32V307 with schematics (PDF only), a datasheet in English, and firmware either bare metal or based on RT-Thread OS to control the eight serial interfaces over Ethernet. Let’s check CH32V305 and CH32V307 MCU specifications first: MCU core – WCH designed RISC-V4F 32-bit RISC-V core up to 144MHz FPU – Single-cycle multiplication and hardware division, hardware float point unit (FPU) ; Memory – Up to 64KB SRAM Storage – Up to 256KB Flash Networking – Gigabit Ethernet MAC, 10 Mbps PHY USB – 1x USB 2.0 OTG full-speed interface, 1x USB […]

January 19, 2022November 19, 2022 by Jean-Luc Aufranc (CNXSoft) - 16 Comments

Add 10GbE to your system with an M.2 2280 module

It’s now possible to add 10GbE through an M.2 socket thanks to Innodisk EGPL-T101 M.2 2280 module based on Marvell AQtion Ethernet controller offering support for 10Gbps, 5Gbps, 2.5Gbps, 1000M, and 100M/10M LAN speeds. The solution is comprised of three parts with the M.2 module equipped with a heatsink to cool the Ethernet controller, a flexible high-speed cable, and a daughter board with an RJ45 connector and two threads for mounting to a chassis. Innodisk EGPL-T101 specifications: Ethernet controller – Marvell AQtion likely AQC113 “single-port 6speed, 10Gbps PCIe to Multi-Gig Ethernet controller with MAC and PHY with I-grade support” M.2 input interface – PCI Express 3.0 x 2 RJ45 connector for up to 10GbE Power Consumption – Up to 2.5W (3.3V, 762mA) Dimensions (W x L x H/mm) M.2 Board: 22 x 80 x 14.5 mm (M.2 2280 form factor) Daughter Board: 31.75 x 28 x 17.7 mm Temperature Range […]

December 7, 2021February 6, 2022 by Jean-Luc Aufranc (CNXSoft) - 22 Comments

Review of an ESP32-based BLE to MQTT gateway – Part 1: GL.inet GL-S10 unboxing and teardown

GL.inet introduced the GL-S10 BLE to MQTT IoT gateway last month with an ESP32 module offering WiFi and Bluetooth connectivity, as well as Ethernet and PoE support. I got offered a sample for review, and just received it together with the optional BLE beacon. So today, I’ll first have a look at the content, and check out the hardware with a teardown. GL.inet GL-S10 unboxing The package shows us the main features with Bluetooth LE 4.2, WiFi, PoE, and external antenna, with GL-S10 described as a BLE IOT GATEWAY connecting IoT devices to the Cloud. The gateway ships with a getting started guide, an antenna, a USB cable for power, as well as the beacon which we can see with a 3M stick tape. On one side, we have the RJ45 connector for Ethernet and a micro USB port for power, while the other side features a reset button, plus […]

September 27, 2021November 15, 2022 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

ZB-GW03 ESP32-based Ethernet Zigbee gateway works with Tasmota firmware

ZB-GW03 is an Ethernet Zigbee Gateway compatible with eWelink mobile app and with a design similar to SONOFF ZBBridge gateway but replacing ESP8266 SoC by ESP32 SoC, and adding an Ethernet port. The ZB-GW03 gateway is apparently based on the same Silicon Labs EFR32MG21 Zigbee Arm Cortex-M33 chip and has been hacked to run Tasmota open-source software for people preferring more flexibility and/or integration with OpenHAB or Home Assistant open-source home automation frameworks via Zigbee2MQTT. ZB-GW03 gateway specifications: Main MCU – Espressif Systems ESP32 dual-core Tensilica TX6 processor @ 240 MHz with WiFi 4 and Bluetooth connectivity Zigbee MCU – Silicon Labs EFR32MG21 Arm Cortex-M33 MCU @ 80 MHz with Zigbee 3.0 connectivity Connectivity 10/100M Ethernet, WiFi, and Bluetooth via ESP32 Zigbee 3.0 via Silabs MG21 MCU with support for 128 nodes, up to 200+ meter range One 2.4 GHz Zigbee antenna One 2.4 GHz PCB antenna for WiFi Misc […]

August 17, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

Raspberry Pi 4 gets IEEE1588 Precision Time Protocol (PTP) with Real-Time HAT

Raspberrry Pi 4 PTP protocol with the real-time HAT

InnoRoute Real-Time HAT adds IEEE1588 Precision Time Protocol (PTP) to Raspberry Pi 4/3 via a Xilinx Artix-7 FPGA and three Gigabit Ethernet ports. The Precision Time Protocol (PTP) is used to very accurately synchronize clocks throughout a computer network to enable measurement and control systems. It is often found in embedded microcontrollers or processors from Texas Instruments, STMicro, and more recently, in Intel Elkhart Lake & Tiger Lake H processors. It can notably be used for Time-Sensitive Networking (TSN) and Audio Video Bridging (AVB). InnoRoute Real-time HAT specifications & key features: FPGA- Xilinx Artik-7 FPGA Some RAM Networking Gigabit Ethernet port 0 with IEEE1588/TSN signaling Gigabit Ethernet port 1 with input from Raspberry Pi 4 Gigabit Ethernet port 2 with PoE, without TSN Host interface – 40-pin Raspberry Pi header mostly for SPI and I2C interfaces used for configuration. Misc – 3x LEDs, JTAG and PMod connectors, EEPROM (for Raspberry […]

July 15, 2021 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Low-cost embedded router SBC offers 2.5 GbE, WiFi 6 through Qualcomm IPQ5018 SoC

Wallys Communication has been offering Qualcomm-based embedded router boards for several years, including the higher-end DR8072A with dual 2.5GbE and WiFi 6 connectivity, followed by a lower-cost WiFi 6 SBC based on IPQ6010 with Gigabit Ethernet ports. But if you’d like to benefit from the lower cost while keeping WiFi 6 and 2.5GbE, the company has now introduced a new model based on Qualcomm IPQ5018 dual-core Cortex-A53 SoC, also found in Xiaomi Mi AX6000 router, with DR5018 embedded router board. The blurry photo above reveals the board is also called AP.MP03, a name that looks like the typical name for Qualcomm reference designs. DR5018 specifications: SoC – Qualcomm Atheros IPQ5018 dual-core Arm Cortex-A53 processor @ 1.0 GHz System Memory – 512MB DDR3L Storage – 4GB or 8GB eMMC flash, 4MB Nor Flash, 128MB NAND flash Networking 4x Gigabit Ethernet Ports or 1x 2.5Gbps Ethernet port 1x Gigabit Ethernet Port On-board […]

July 2, 2021 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

UP Connect Plus adds 5G support, 3 GbE ports to UP Core Plus, UP Xtreme SBCs

AAEON UP Connect Plus is a carrier board with three Gigabit Ethernet (GbE) ports, and an M.2 slot plus a micro SIM card socket adding support for 5G cellular connectivity to the company’s Appolo Lake-based UP Core Plus and Whiskey Lake-powered UP Xtreme single board computers. UP Connect Plus specifications: Connectivity 3 Gigabit Ethernet RJ45 ports in two configurations: 3x Intel Ethernet Controller I211-AT 3x Intel Ethernet Controller I210-IT with wide temperature and TSN (Time-sensitive Networking) 5G cellular – M.2 3042/3052 colay socket with micro-SIM card port to support 4G/5G modules USB – 1x USB 3.0 Type-A port for UP Core Plus only PCIe – 1x 2 channel PCIe switch SBC connectors – 2x 100-pin high-speed docking connectors Power Supply – 12V/5V from the main board Power Consumption – Approximately 36 to 40 Watts with UP Core Plus + UP Connect Plus Dimensions – 90 mm x 56 mm Temperature […]