gateway News - Page 23 of 32 - CNX Software

November 11, 2019November 11, 2019 by Jean-Luc Aufranc (CNXSoft) - 21 Comments

NanoPi R1S Dual Gigabit Ethernet Router Comes with 32-bit or 64-bit Arm Processor

FriendlyELEC launched NanoPi R1 SBC & Gateway earlier this year with Allwinner H3 processor, two Ethernet ports, as well as WiFi and Bluetooth connectivity. The design makes use of both Ethernet on the processor, but that also means on Gigabit Ethernet port had to be combined with a Fast Ethernet processor. The company has now added a USB to Gigabit Ethernet bridge to their latest NanoPi R1S board meaning it’s now a dual Gigabit Ethernet SBC, but with the caveat that the port behind the USB bridge is limited to USB 2.0 speed (480 Mbps), and with overhead the USB Ethernet bandwidth is around 330 Mbps. There are two versions of the board, namely NanoPi R1S-H3 and R1S-H5 with respectively Allwinner H3 32-bit processor, and Allwinner H5 64-bit processor. Apart from the different processors, both boards share the same PCBA and specifications: SoC NanoPi R1S-H3 – Allwinner H3 quad-core Arm […]

October 16, 2019October 16, 2019 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Semtech SX1302 LoRa Transceiver to Deliver Cheaper, More Efficient Gateways

After our interview with Rak Wireless CEO, we received a comment inquiring about the availability of SX1302 gateways. Semtech so far had two LoRa transceivers for gateways namely SX1301 and SX1308, but I had never heard about a third one. Semtech SX1302 is brand new, the latest generation of baseband LoRa chip for gateways that is said to reduce current consumption in order to simplify the thermal design of gateways, as well as the BoM (bill of materials) costs), while being capable of handling a higher amount of traffic. Semtech SX1302 LoRa Transceiver Key features: Up to -141 dBm sensitivity with SX1250 Tx/Rx front-end 125 kHz LoRa reception with: 8 x 8 channels LoRa packet detectors 8 x SF5-SF12 LoRa demodulators 8 x SF5-SF10 LoRa demodulators 125 /250 / 500 kHz LoRa demodulator (G)FSK demodulator Direct interface to Semtech transceivers SX1255, SX1257 and SX1250 SPI host interface Single 32 MHz […]

October 15, 2019October 15, 2019 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

Intel Denverton based Fanless Network Appliance Comes with 6x Ethernet Ports, 2x SFP Cages

PL-82000 Denverton Fanless Network Appliance

Intel Atom C3000 “Denverton” processors were introduced in 2016 for low power servers and network appliances with four to sixteen cores, and in the following years, many products based on the SoC were launched including GIGABYTE MA10-ST0 server motherboard, AAEON FWS-2360 desktop network appliance, and Supermicro A2SDi-2C-HLN4F Mini-ITX motherboard among others. New Denverton platforms did not get much coverage on CNX Software in the last couple of years, and an article on LinuxGizmos reminded me those still existed, as US-based WIN Enterprises recently launched LP-82000 fanless network appliance powered by Intel Denverton C3338, C3558, or C3758 processor and featuring six Gigabit Ethernet ports, as well as two SFP cages. LP-82000 specifications: SoC (one or the other) Intel Denverton C3338 dual-core processor @ 1.50 GHz / 2.20 GHz (Turbo); 4 MB cache; TDP: 8.5 W Intel Denverton C3558 quad-core processor @ 2.20 GHz; 8 MB cache; TDP: 16 W Intel Denverton […]

October 12, 2019 by Karl Johnson - 4 Comments

How I Adopted a Ubiquiti Unifi Security Gateway on my Existing Home Network

Hey Karl here with a quick write up on how I adopted a Ubiquiti Unifi Security Gateway (USG) into my existing home network. I ran into a few issues so I wanted to share and hopefully help someone else. I have had 2 Unifi access points cover my home for several years now and I recently upgraded my internet to 100 Mbps. I was maxing out at about 95 Mbps with downloads on my existing 100 Mbps Linksys router and I knew I was leaving some bandwidth on the table. Spectrum is my internet provider and I have always got more than what I paid for. I placed an order on Amazon and 24 hours later it was delivered. I have a couple of things that made this challenging. First I run my network on a 10.0.0.1/24 subnet with devices that have static IP address and I host my own […]

September 12, 2019February 16, 2020 by Jean-Luc Aufranc (CNXSoft) - 14 Comments

Habanero Qualcomm IPQ4019/IPQ4029 SoM Brings 802.11ac Wave2 WiFi to Linux Gateways and Routers

Last April, we first wrote about Qualcomm IPQ4019 quad-core Cortex-A7 processor with built-in 802.11ac Wave 2 WiFi, as it was found in Qualcomm Mesh Networking DevKit with support for Amazon Alexa. A few months later, we discovered router boards powered by either IPQ4019 or IPQ4029 processor such as Dakota DR40X9 or MikroTik RB450Gx4. The latter does not come with WiFi at all and instead leverages the hardware IPSec encryption built-into the processor. Habanero System-on-Module Today, we’ve come across the first IPQ4019 / IPQ4029 system-on-module we’ve countered so far, courtesy of 8devices with their Habanero and Habanero-I 802.11ac Wave 2 modules based on the respective processors. Habanero(-I) specifications: SoC – Qualcomm IPQ4019/IPQ4029 quad-core Arm Cortex-A7 processor @ 717 MHz with NEON, FPU, hardware-based NAT engine, and crypto accelerator System Memory – 512 MB DDR3L RAM Storage – 32MB NOR flash; up to 1 GB NAND flash on baseboard Connectivity QCA8075C 5-port […]

July 23, 2019January 9, 2020 by Ayo Ayibiowu - 6 Comments

N-Fuse Launches Raspberry Pi 3B+ LoRaWAN Gateway with PoE Support

PoE enabled Raspberry Pi 3B+ based LoRaWAN™ Gateway

Raspberry Pi is everywhere, and this small size single-board computer has reshaped technology and STEM education. The launch of the recent Raspberry Pi 4 is evident in the success and continuous growth. The Raspberry Pi 3B+ has seen so much success in several maker’s projects, while not the most powerful SBC in the market, but undoubtedly one of the most popular. I once put together an AI-powered mobile robot using just a Raspberry Pi 3B+, an RPLidar A2, and Raspberry Camera which was way capable of so many things. Another exciting Raspberry Pi end product is the “PoE enabled Raspberry Pi 3B+ based LoRaWAN Gateway” from n-fuse. The PoE enabled Raspberry Pi 3B+ based LoRaWAN Gateway as called by n-fuse is a LoRaWAN gateway based on the Raspberry Pi 3B+, the LRWCCx-MPCIE Concentrator, and the SBCPoE RPI Hat. It supports both the Europe 868Mhz and America 915Mhz frequency (you have […]

July 19, 2019July 19, 2019 by Ayo Ayibiowu - 2 Comments

MikroTik is Launching a new set of LoRa products this summer

MikroTik, the Latvian network equipment manufacturer, is reportedly launching a new set of IoT LoRa devices this summer. MikroTik who has been traditionally known for its wireless technologies, especially products related to wireless networking like routers, switches, antennas, and others, is going full fledged in support of LoRa network, the promising LPWAN technology for IoT applications. MikroTik announced a new LoRa based Gateway product in Vienna back in March 2019 during the MUM Europe MikroTik User Meetings. It was a combination of a wAP 2GHz outdoor AP with a LoRaWAN card inbuilt inside and will work just like every other LoRa gateways out there. The gateway is expected to support both public and private network server. According to MikroTik, they promised to cut down the high-end prices of LoRa gateway: We will undercut that price be a very very big difference, so our LoRa gateway will much much more affordable than […]

July 3, 2019July 3, 2019 by Tiwalade Joanna Okedara - 2 Comments

M2M-IoT GW-01 LoRaWAN Gateway is equipped with Orange Pi Zero H2+ SBC

M2M-IoT has developed a new LoRa gateway. The gateway, GW-01, is based on Orange Pi Zero H2+ board. While it is new, it has a lot of useful features. The new GW-01 gateway operates in the 868MHz or 915MHz LoRa frequencies and has -139 dBm sensitivity. Furthermore, the GW-01 is fully functional. It is also an open source low-cost solution to developing a LoRaWAN network. In addition, the gateway supports both OpenWrt, and Armbian distributions, and you’ll find documentation for both on Github. Another great thing about the gateway is that it has two boards. Also, the first board, which is on top, is based on SX1301. This 8 channel LoRa concentrator implements the LoRa physical interface. Now, the second board is at the bottom. It is also the model that the whole gateway was based on. This board is the OrangePi Zero H2+ 256MB (RAM) development board. The gateway […]