industrial News - Page 63 of 100 - CNX Software

October 27, 2021 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

CompuLab IOT-GATE-RPI4 gateway targets industrial control and monitoring

Compulab IOT-GATE-RPI4 CM4 industrial gateway

Compulab IOT-GATE-RPI4 is another industrial gateway based on the Raspberry Pi CM4 module that offers a different feature set and form factor compared to solutions like TECHBASE iModGATE-AI gateway or QWave Systems CatsPi Industrial carrier board. Designed with industrial control and monitoring in mind, the IOT-GATE-RPI4 gateway offers multiple RS485, RS232 and CAN FD ports, Ethernet, 4G LTE/4G, WiFi 802.11ac, and Bluetooth 5.0 connectivity, as well as a wide -40°C to 80°C operating temperature range, plus a wide input voltage from 8V to 36V as well as PoE support. Compulab IOT-GATE-RPI4 specifications: SoM – Raspberry Pi Compute Module 4 (CM4) with SoC – Broadcom BCM2711 quad-core ARM Cortex-A72 @ 1.5GHz plus VideoCore IV GPU with H.265 (4Kp60 decode), H.264 (1080p60 decode, 1080p30 encode) System Memory – 1GB to 8GB LPDDR4 Storage – 16GB to 128GB eMMC flash soldered on-board Secondary Storage – 64GB – 256GB NVMe flash via optional module […]

October 22, 2021November 15, 2022 by Jean-Luc Aufranc (CNXSoft) - 27 Comments

Intel Celeron J6412 thin Mini-ITX motherboard offers four Ethernet ports

Intel Celeron J6412 thin mini-ITX motherboard quad ethernet

BCM Advanced Research is now sampling the MX6412J thin mini-ITX motherboard equipped with an Intel Celeron J6412 quad-core Elkhart Lake processor, up to 32 GB RAM via two SODIMM DDR4 memory slots, SATA and NVMe storage, as well as found Ethernet ports with namely two 2.5GbE and two Gigabit Ethernet RJ45 ports. Designed for fanless operation with a large yet thin heatsink, the industrial motherboard also sports two HDMI 4K video outputs, nine USB 3.0/2.0 ports, variable 12-24 DC input, as well as several serial ports, and more. BCM MX6412J specifications: SoC – Intel Celeron J6412 quad-core Elkhart Lake processor @ 2.0 GHz / 2.6GHz (Burst frequency) with 1.5MB cache, 16 EU Intel UHD Graphics; 10W TDP System Memory – 2x 260-pin SODIMM DDR4 memory slots for up to 32GB RAM (Note: Intel Ark list the 32GB limit for the processor, but sometimes they really mean per socket/channel) Storage – […]

October 17, 2021 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

Zidoo M6 preview with Android 11

I’ve now had more time to play with Zidoo M6 Arm mini PC powered by a Rockchip RK3566 quad-core Cortex-A55 processor. I intended to review the device with Ubuntu, but I misunderstood, and Android 11 was pre-installed on the device. I was also told since this model is mainly for industrial control, I might want to focus on performance and connectors rather than how well all functions work. So this will not be a review, but rather a preview of Zidoo M6, since as we’ll see below there’s still more work do to fix all issues. As an industrial platform. some features like Google Services may not be needed or even desirable. First boot and Settings I’ve connected a USB keyboard for screenshots, MINIX NEO A2 Lite air mouse, an HDMI cable to my 4K TV, and the power supply to get started. I also add two AAA batteries to […]

October 11, 2021August 14, 2022 by Jean-Luc Aufranc (CNXSoft) - 11 Comments

IBASE launches 3.5-inch SBC with AMD Ryzen Embedded V2000 processor

We’ve covered plenty of AMD Ryzen Embedded V2000 SBCs in the past, but it appears IBASE IB952 might be the first 3.5-inch SBC with a Ryzen V2000 processor for the industrial and IoT markets. The board supports up to 64GB RAM, offers two SATA III ports for storage, dual Gigabit Ethernet networking, four display outputs with DisplayPort, eDP and LVDS interfaces, USB and serial ports, as well as expansion through two M.2 sockets. IBASE IB952 specifications: SoC – AMD Ryzen Embedded V2000 with Radeon Vega graphics System Memory – DDR4-2400 SO-DIMM, up to 64GB with ECC support Storage 2x SATA III ports M.2 M-Key socket for NVMe SSD Flash for AMI BIOS Video Output 1x DisplayPort 1.4 port up to 4Kp60 1x DisplayPort 1.2 port via USB-C port up to 4Kp60 1x 24-bit dual-channel LVDS up to 1080p60 1x eDP (embedded DisplayPort) up to 4Kp60 Four independent display support Audio […]

October 9, 2021October 11, 2021 by Jean-Luc Aufranc (CNXSoft) - 10 Comments

Iono RP – An industrial PLC with a Raspberry Pi RP2040 MCU

Raspberry Pi RP2040 MCU has been used in many boards, but I think I had seen the dual-core MCU in a PLC, or even any industrial products just yet. Sfera Labs Iono RP is a compact I/O module (PLC) with a Raspberry Pi RP2040 microcontroller that’s programmable in C/C++ and MicroPython, or even the Arduino IDE. The DIN-Rail mountable, RP2040 based industrial PLC offers digital and analog input and output lines, power relays, and an RS-485 interface, supports power input from 12V-24V with all signals accessible through terminal blocks. Sfera Labs can also provide some optional options such as an RTC or an earthquake sensor module. Iono RP PLC specifications: MCU – Raspberry Pi RP2040 dual-core Arm Cortex-M0+ @ 133MHz with 264kB on-chip SRAM Storage – 16MB SPI flash, optional microSD card slot Communication interface – standard RS-485 interface with electrostatic discharge protection Inputs/Outputs via terminal blocks 4x power relay […]

October 7, 2021 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

PICMG IoT.1 firmware specification targets IoT sensors and effecters

The PICMG consortium is better known for COM Express and COM HPC standards for x86 industrial computers-on-module, but last year they started catering to the IIoT sector with the introduction of the microSAM System-on-Module (micro Sensor Adapter Modules) standard for microcontrollers and IIoT sensors. The consortium has now ratified the IoT.1 firmware specification defining a communication standard between sensors/effecters and local IoT controllers such as microSAM specified by PICMGs IoT.0 specification. The PICMG IoT.1 standard, developed in collaboration with the Distributed Management Task Force (DMTF), defines a vendor-agnostic firmware interface and low-level data model that builds upon the Platform Level Data Model (PLDM) low-level messaging system, and adds features specific to industrial automation and control use cases. If like me, you’ve never heard about PLDM, PICMG explains: The PLDM is a low-level messaging system that supports topologies, eventing and discovery and runs over a variety of system level buses such […]

October 6, 2021 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

Portenta H7 Lite Connected brings back WiFi & Bluetooth

Arduino has launched another Arduino Pro board! Well, sort of. Let’s not get too excited. The Portenta H7 Lite Connected is based on last month’s Portenta H7 Lite that itself was a cost-optimized version of Portenta H7 board without a wireless module, USB-C video output, and only fitted with the lower cost Microchip ATECC608 secure element. Portenta H7 Lite Connected is exactly the same board, except it brings back the Murata 1DX module with 2.4GHz 802.11b/g/n WiFI 4 and Bluetooth 5.1 BR/EDR/LE connectivity, plus the related u.FL antenna connector. Portenta H7 Lite Connected specifications: Microcontroller – STMicro STM32H747XI Cortex-M7 @ 480 MHz + M4 @ 200 MHz MCU with 2MB dual-bank Flash memory, 1 MB RAM, Chrom-ART graphical hardware accelerator System Memory – 2MB SDRAM (upgradeable up to 64MB) Storage – 16MB QSPI NOR Flash (Upgradeable up to 128MB) Connectivity 2.4GHz WiFi 802.11b/g/n up to 65 Mbps and Bluetooth 5.1 […]

September 30, 2021September 30, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

M5Stack TOUGH – A weatherproof ESP32 Industrial IoT controller

M5Stack TOUGH weatherproof ESP32 display

M5Stack has launched several ESP32 WiFi & BLuetooth IoT controllers with an integrated display such as M5Stack Core2. The latest model, M5Stack TOUGH, is a little different as it is rugged and waterproof/weatherproof with a UV resistant enclosure sealed with o-ring, and offering waterproof M12 connectors. With protection against solid objects, dust, sand, dirt, and water drops, as well as variety of installation options such as screw mount, rolled strip, magnetic and adhesive back, the M5Stack TOUGH is suitable for more demanding environments from kitchens to factory floors, and outdoor data acquisition. M5Stack TOUGH specifications: SoC – Espressif ESP32-D0WDQ6-V3 dual-core processor @ 240 MHz with 520 KB, 2.4 GHz WiFi, and dual-mode Bluetooth Extra RAM – 8MB PSRAM Storage – 16MB Flash, MicroSD card slot up to 16GB Display – 2-inch color LCD with multi-touch capacitive screen, 320×240 resolution, 853nit brightness; ILI9342C display driver and CHSC6540 chip Audio – NS4168 […]