Linux News - Page 175 of 434 - CNX Software

August 5, 2019August 5, 2019 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

Pine64 SoEdge-RK1808 AI Module Delivers 3.0 TOPS via Rockchip RK1808 SoC

SOPINE Model A Baseboard + SoEdge-RK1808

A few weeks ago, Ameridroid reported Pine64 would soon launch SoRock and SoEdge systems-on-module, but at the time there was virtually no info except SoRock would be likely based on either RK3328 or RK3399 and work on the existing Clusterboard, while SoEdge would be an AI Neural module for Artificial Intelligence tasks, with up to 3 TeraFLOPS of performance. I did not write about it at the time, simply because there was so little information, but this morning I’ve just received some photos of SoEdge-RK1808 module fitted to a baseboard that looks to be SOPINE Model “A” carrier board. SoEdge-RK1808 SoM Let’s try to derive the specifications from the photos even though some components appear to be blurred out or just unclear: SoC – Rockchip RK1808 dual-core Cortex-A35 processor with 3.0 TOPS NPU (Neural Processing Unit) System Memory – 2GB RAM (2x 8GBit Micro DDR4-2400) but limited PC-2133 Storage – […]

July 31, 2019August 4, 2019 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

BeagleBone Green Gateway SBC Adds Octavo OSD3358 SiP, Ethernet, and a DC Jack

BeagleBone Green Wireless was launched in 2016 as an alternative to the official BeagleBone Green with WiFi & Bluetooth connectivity, and some extra USB ports meaning the Ethernet port had to go. The Linux SBC was based on Texas Instruments Sitara AM3358 processor and a 512 MB RAM chip. Seeed Studio has been working on an update of the board named BeagleBone Green Gateway that combines the processor, the RAM chip, and more components into one thanks to Octavo Systems OSD3358 SiP. The new board also adds Ethernet, a DC jack for power instead of just relying on micro USB, and an I2C RTC chip and battery. BeagleBone Green Gateway specifications with changes highlighted in bold: SiP – Octavo Systems OSD3358 with Texas Instruments AM3358 Arm Cortex-A8 processor @ 1.0 GHz, 2×32-bit 200-MHz programmable real-time units (PRUs), 3D graphics accelerator, 512MB DDR3 SDRAM, 4KB EEPROM, and integrated power management Storage […]

July 31, 2019 by Jean-Luc Aufranc (CNXSoft) - 24 Comments

Orange Pi Zero LTS SBC Launched for $8.49 and Up

Orange Pi Zero LTS is an update to Orange Pi Zero Allwinner H2+ board with the same specifications, but tweaks to the hardware that Shenzhen Xunlong Software claims lower power consumption and reduce heat. The SBC supports Armbian’s Debian and Ubuntu images, and best suited for headless applications that require network connectivity via Ethernet and/or WiFi such as smart speakers. The board also features one USB port, and two I/O headers for expansion. The good news is that you can now buy Orange Pi Zero LTS for the same price as the original model, namely $8.49 for the 256MB RAM version, and $10.49 for the 512MB model$10.49 for the 512MB model, excluding shipping costs ($4.73 to my location). Here’s a reminder of Orange Pi Zero LTS (v1.5) specifications: SoC – Allwinner H2+ quad-core Cortex A7 processor @ 1.2 GHz with Mali-400MP2 GPU @ 600 MHz System Memory – 256 to […]

July 30, 2019July 30, 2019 by Jean-Luc Aufranc (CNXSoft) - 10 Comments

Librem 5 Linux Smartphone Specifications Finalized

If you were interested in purchasing, or more exactly pre-ordering, a privacy-focused, open source Linux smartphone with clearly defined hardware specifications, Purism Librem 5 was not quite for you. Until today that is, as while the company did not commit to exact specifications at the beginning of the project, Purism has now revealed the full specifications of Librem 5 Linux smartphone. Librem 5 specifications: SoC – NXP i.MX8M quad-core Cortex A53 @ up to 1.5GHz, Cortex-M4 real-time core, 3G GPU with OpenGL/ES 3.1, Vulkan, OpenCL 1.2 support System Memory – 3GB RAM Storage – 32GB eMMC flash, MicroSD slot up to 2 TB Display- 5.7″ IPS TFT touchscreen with 1440×720 resolution Connectivity Cellular Option 1 – Gemalto PLS8 3G/4G modem w/ single sim on replaceable M.2 card Option 2 – Broadmobi BM818 (made in China) nanoSIM tray Dual-band 802.11a/b/g/n WiFi 4, Bluetooth 4.0 GPS – Teseo LIV3F GNSS Cameras – […]

July 26, 2019July 26, 2019 by Jean-Luc Aufranc (CNXSoft) - 21 Comments

How to Overclock Raspberry Pi 4 to 2.0 GHz

Yesterday I played with my new “ICE Tower CPU cooling fan” for Raspberry Pi 4 which cools the board just great but is clearly over the top. Regular reader and commenter m][sko mentioned it was possible to overclock Raspberry Pi 4 to 2.0 GHz after a firmware upgrade. That looks like a perfect task for my new fansink! I’ve upgraded both the firmware and operating system:

sudo rpi-update
sudo apt dist-upgrade

1 2	sudo rpi-update sudo apt dist-upgrade

then edited /boot/config.txt as root (sudo) to add the following lines to boost the maximum frequency to 2.0 GHz:

force_turbo=0
arm_freq=2000
over_voltage=6

force_turbo=0

arm_freq=2000

over_voltage=6

Do not try to set force_turbo=1, as while it would allow to further boost the voltage, it will change a fuse in the chip, and it will void your warranty. We can now reboot the board to validate the settings, and check those are applied:

vcgencmd get_config int | grep "arm\|over"
arm_freq=2000
over_voltage=6

vcgencmd get_config int | grep "arm\|over"

arm_freq=2000

over_voltage=6

Good. At idle the frequency is lower, but that normal:

vcgencmd measure_clock arm
frequency(48)=666826176

1 2	vcgencmd measure_clock arm frequency(48)=666826176

Voltage is set to 1.0335V:

vcgencmd measure_volts
volt=1.0335V

1 2	vcgencmd measure_volts volt=1.0335V

[…]

July 25, 2019July 26, 2019 by Jean-Luc Aufranc (CNXSoft) - 28 Comments

PineBook Pro Arm Linux Laptop now up for pre-order for $199.99

Pine64 unveiled a Pinebook Pro laptop prototype at FOSDEM 2019 as an update to the original Allwinner A64 powered Pinebook laptop, but instead of just being a toy to play with, Pinebook Pro aimed to be used as a daily driver thanks to a relatively powerful Rockchip RK3399 processor combined with 4GB RAM, and 64/128GB storage, and equipped with a 14″ Full HD display all for a target price of $200. Last May, we noticed some good progress on the software development side with a demo showcasing Ubuntu & Debian with MATE desktop, 4K video playback, 3D graphics acceleration, and USB-C video output. The good news is that Pinebook Pro has just launched and can be pre-ordered for $199.99 on Pine64 store. [Update: If you are an existing forum member, you may want to redeem your coupon here] Pinebook Pro laptop specifications: SoC – Rockchip RK3399 big.LITTLE hexa-core Arm Cortex […]

July 24, 2019 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Waveshare Jetbot AI Kit for NVIDIA Jetson Nano Board Sells for $100 and Up

NVIDIA Jetson Nano developer kit was launched for $99 last March with impressive specifications for the price including one module with four Arm Cortex-A57 cores, a 128-core Maxwell GPU, and 4GB LPDDR4 RAM. The company also introduced Jetbot robot based on the new board, with all instructions available on Github, but until now you had to put some efforts to build it up as the fairly long list of parts had to be purchased or 3D printed separately. It’s now become easier, as Waveshare has started selling their Jetbot AI kit on Amazon for $122.99 without Jetson Nano, and $259.99 with, meaning you may be better off purchasing NVIDIA board separately for around $100, or you may purchase the complete kit directly on Waveshare website for $215.99 plus shipping, or $99.99 without the SBC. Jetbot AI kit content: Optional NVIDIA Jetson Nano SBC 64GB micro SD Card Metal box Camera […]

July 23, 2019 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

AFRd Auto Frame Rate Daemon Works with 64-bit Amlogic Processors

Automatic frame rate switching in TV box ensures video output matches the video frame rate in order to avoid skipped frames (judder) from time to time, and makes the videos much smoother to watch, especially to trained eyes. The problem is that the feature is not always implemented, and/or does not work for all apps. AFRd auto frame rate daemon aims to solve this issue by automatically switching video output to match the video framerate – e.g. 23.976 fps or 59.94 fps – on Android TV boxes powered by one of Amlogic 64-bit processors, be it S905, S905X, S905X2, S912, S905W and other more recent Armv8 processors from the company. Developed by Andrey Zabolotny (anpaza), AFRd is Linux daemon can be linked to either bionic for Android, or glibc for Linux operating systems, and the source code can be found on Github. It relies on two techniques to detect the […]