sonoff News - Page 9 of 9 - CNX Software

July 4, 2017 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

Sonoff B1 is an $18 Hackable WiFi RGB LED E27 Light Bulb based on ESP8285 WiSoC

Earlier this year, I wrote about an ESP8266 based RGB LED “AI Light” lightbulb that was hacked to run ESPurna open source firmware. That’s all good, except some people tried to get one, and ended with a different hardware. So if you’d like something that’s more of a “sure thing”, ITEAD Studio has designed Sonoff B1 dimmable RGB LED E27 light bulb based on ESP8285 processor, and with a “4 pads” to allow for custom firmware flashing. Sonoff B1 hardware specifications: Typical Lumen Output – 600lm Beam Angle – 120 degrees typ. Color Temperature – 2800K-6500K & RGB full color Connectivity – WiFi 802.11 b/g/n @ 2.4GHz Power Supply – 90-260V AC 50/60Hz via E27 base Power Consumption – Light off: 0.5W Max; rated power: 6W Temperature Range – Operating: 0ºC~ 40ºC; storage: -20ºC~ 80ºC Operating Humidity – 5%-90% RH Sonoff B1 with stock firmware can be controlled using the […]

June 14, 2017 by Jean-Luc Aufranc (CNXSoft) - 10 Comments

$23 Sonoff 4CH Pro 4-Channels WiFi & RF Switch Ships in a DIN Rail Enclosure

ITEAD Studio’s Sonoff family is a collection of really useful and inexpensive home automation devices which have been featured multiple times on CNX Software with either to stock firmware and eWelink app, or open source firmware developed by the community. I’m using a Sonoff TH16 to control a water pump, a Sonoff Pow to monitor my office’s power consumption, and Karl used some Sonoff switches to control his lights at home. The company has now launched Sonoff 4CH Pro with 4 relays that can be controlled with buttons on the unit, WiFi, or RF remote controls, and comes in a DIN Rail enclosure. Sonoff 4CH Pro switch specifications: Connectivity – ESP8266 WiFi module and 433 MHz receiver Relays – 4x HUIKE 230V/10A relays (max 2200W per relays) with NC and NO connection Configuration – K5 & S6 switch for mode selection; K6 switch for time selection (0.5 to 4s) Misc […]

March 1, 2017 by Jean-Luc Aufranc (CNXSoft) - 28 Comments

Some Sonoff TH16 and Sonoff POW Manufactured in December 2016 / January 2017 Are Being Recalled

Sonoff TH16 and Sonoff POW are inexpensive and useful wireless switches based on ESP8266 WiSoC. I’m using Sonoff TH16 to control a water pump, and Sonoff POW to monitor my office power consumption. I received mine in early November 2016, so they were probably manufactured sometimes in October. Does manufacturing month matter? Yes, it does, as ITEAD Studio has just issued a recall notice for both devices for a batch manufactured between December 2016 and January 2017. The problem is that while the switches come with a 16A relay, the trace were not thick enough, and if you connect a device that draws enough power, they would heat enough to make the case slowly melt. The problem is that ITEAD Studio asked the factory to add “sufficient tin to the wires to ensure low enough impedances”, but they did not quantify it clearly, and that’s why the product is not […]

February 27, 2017April 22, 2017 by Karl Johnson - 30 Comments

Karl’s Home Automation Project – Part 1: Home Assistant & YAML, MQTT, Sonoff, and Xmas Lights

Karl here. I am here to write about my home automation project. First thing I want to say is that I am very cost conscious and I don’t mind putting in extra effort into the setup of things to keep costs down. I did invest a lot of time and had to do a lot of reading to get my project going. It took while and I received a lot of groans from my wife while testing. I am still in the process of tweaking things. I started watching a series of videos on YouTube from Bruh Automation. He introduced me to Home Assistant. It got me really excited. He uses a Raspberry Pi as a server but I already had a Wintel Pro CX-W8 Smart TV Box which I use as a server. I run 3 Minecraft Servers, Emby Server, iSpyConnect DVR (2 IP Cameras), Unifi wifi controller, and […]

January 21, 2017January 21, 2017 by Jean-Luc Aufranc (CNXSoft) - 13 Comments

How to use Sonoff POW with ESPurna Firmware and Domoticz Home Automation System

Sonoff POW is an ESP8266 based wireless switch with a power meter that comes pre-loaded with a closed-source firmware that works with eWelink app for Android or iOS by default. But we’ve also seen Sonoff POW, and other Sonoff wireless switches from the same family, can be flash with open source firmware supporting MQTT (Message Queuing Telemetry Transport) lightweight messaging protocol such as ESPurna, and I initially sent data from Sonoff POW to ThingSpeak via an MQTT broker (mosquitto) to draw some pretty charts. I did that with the switch connected to a lightbulb, but I’ve since installed Sonoff POW in my office to measure the room’s power consumption minus the ceiling light and aircon as shown below. Sonoff cable mechanism is really a pain for hard copper wires, as they are hard to push inside the mechanism, and something come out. I finally managed by it took longer than […]

January 19, 2017January 19, 2017 by Jean-Luc Aufranc (CNXSoft) - 8 Comments

How to Install Domoticz Home Automation System in NanoPi NEO and Other ARM Linux Boards

I’ve recently started experimenting with IoT projects, and the first hurdle is to select the hardware and software for your projects are there are simply so many options. For the hardware your first have to choose the communication protocols for your sensors and actuators, and if you are going to go with WiFi, ESP8266 is the obvious solution, used together with your favorite low cost Linux development board such as Raspberry Pi or Orange Pi to run some IoT server software locally or leveraging the cloud. But the most difficult & confusing part for me was to select the server software / cloud services as there are just so many options. I prefer having a local server than something running only in the cloud, as my Internet goes a few hours a month, so I started with a solution combining ThingSpeak with MQTT gathering data from Sonoff power switches running […]

December 21, 2016June 25, 2023 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

Sonoff SC WiFi Environmental Monitor mini Review

Yesterday I received two environmental monitors with Sonoff SC and vThings CO2 Monitor, and while I’ve plugged both, I have not had time to look into vThings documentation, but since I’m already using the eWelink app for Sonoff TH16 wireless switch, setting up Sonoff SC just took me a few minutes, so I’ll report my experience with the device in this review. I powered Sonoff SC using the USB port of my modem router, and the green LED on the back of the device started to blink every 2 or 3 seconds. Then I started the eWelink app on my Android phone and taped on the “+” icon to add a new device following the instructions here which are basically the same for all Sonoff devices. Then you need to press the “Audio” button for about 5 seconds until the green LED blinks faster, at which point you can click […]