touchscreen News - Page 6 of 8 - CNX Software

August 21, 2022 by Karl Johnson - 7 Comments

Making a DIY 10.1-inch All-in-One PC out of AMR5 Ryzen 5 gaming mini PC

Hey Karl here. The first thing I need to do is thank the manufacturer of the brand Ace Magician for sending over a unit of their AMR5 gaming mini PC to more or less play with. I did a tiny bit of benchmarking along the way. This is the last time you will see the system in this state 😀 Story time. I have been really wanting a Steam Deck. But we purchased a Nintendo Switch about a year ago and it has barely been used. As soon as my son picked it up he asked why it was so laggy and has shown very little interest in it. So that got me worried about purchasing essentially a one-trick device. There have been a couple of good attempts at a DIY Steam Deck and I wanted to experiment with a small form factor. I went into this with a general […]

August 8, 2022August 8, 2022 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Orange Pi 4 SBC gets 10.1-inch LCD touchscreen

Shenzhen Xunlong Software has released a 10.1-inch LCD touchscreen for the company’s Orange Pi 4 single board computer powered by a Rockchip RK3399 hexa-core Cortex-A72/A53 processor. The MIPI DSI display is based on Ilitek ILI9881c panel controller supported in mainline Linux, offers 1280×800 resolution, and besides working with the original Orange Pi 4, it’s also compatible with Orange Pi 4B (with AI accelerator) and the more recent Orange Pi 4 LTS SBC launched earlier this year. 10.1-inch LCD touchscreen specifications: Display Controller – Ilitek ILI9881C (See PDF datasheet) 10.1-inch panel size 1280×800 resolution @ up to 60Hz, with 16.7 million colors Luminance – 250 cd/m2 (or nit) Backlight – 27x white LEDs Brightness control with PWM 10-point multi touchscreen Host interface – MIPI DSI Dimensions Active area – 216.58 x 135.36 mm Outline dimensions – 228.6 x 143 x 2.7 mm Weight – TBD Temperature Range – Operating – 0 […]

July 28, 2022 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Review of SunFounder TS7-Pro 7-inch touchscreen display for Raspberry Pi 4

Unboxing SunFounder TS7-Pro touchscreen display SunFounder TS7-Pro is a 7-inch touchscreen display designed for Raspberry Pi 4 board and the company sent us one review sample for evaluation. SunFounder has a wide range of Raspberry Pi and Arduino accessories designed for makers, and the TS7-Pro 7 is their latest offering that’s optimized to work with Raspberry Pi 4 and Raspberry Pi 3. Adding a touchscreen display to a Raspberry Pi may be a bit messy with the display or other accessories such as cameras and/or 2.5-inch drive spread on the table, but the TS7-Pro display simplifies all that with a neater assembly. Let’s start the review with an unboxing The package is compact and the display is well-protected with polyethylene foam to reduce the risk of damage during transport. Accessories such as cables, screws and nuts, adapters, an acrylic enclosure, and a screwdriver are also included in the package. Here’s […]

July 26, 2022July 26, 2022 by Jean-Luc Aufranc (CNXSoft) - 12 Comments

GOLE1 Pro mini PC comes with 5.5-inch touch screen display, Gemini Lake processor (Crowdfunding)

GOLE1 was quite a unique mini PC when it launched in 2016 as it included a 5-inch touchscreen display. HIGOLE is now back with the GOLE1 Pro based on a similar design, but a slightly larger 5.5-inch touchscreen display, and much better specs suitable for 2022’s software and entry-level use cases. The Atom x5-Z8300 “Cherry Trail” processor found in the original device gives way to an Intel Celeron N4200 or J4125 Gemini Lake processor, and the GOLE1 Pro mini PC, which the company sometimes also calls “HIGOLE PC 2022”, comes with up to 8GB LPDDR4X, a 128GB SSD, Gigabit Ethernet, WiFI 6 or 5, four USB 3.0 ports, and more. GOLE1 Pro specifications: SoC (one or the other) Intel Celeron J4125 quad-core processor @ 2.00 GHz / 2.70 GHz (Turbo) / 2.4 GHz (Turbo all cores) with 12EU Intel UHD Graphics 600 @ 250 MHz / 750 MHz (Turbo); 10W […]

January 24, 2022January 25, 2022 by Jean-Luc Aufranc (CNXSoft) - 20 Comments

Building a NanoPi M4V2 based All-in-One Linux PC running Armbian (Ubuntu/Debian)

At the end of my review of “RPI All-in-One” PC with Raspberry Pi 4, I noted the system also appeared to be compatible with NanoPi M4V2 single board computer. I’ve now tried it out, and assembling the board inside the 10.1-inch display is even easier than I initially thought. That means I now have a NanoPi M4V2 All-in-One PC running Ubuntu Hirsute or Debian Buster with XFCE desktop environment from Armbian, and most features work including the display and wireless connectivity, but I still have an issue with the touchscreen function. Here are the steps I followed initially: Download Armbian Buster XFCE image from Armbian and flash it to a microSD card with tools like USBimager. Insert the microSD card in the board Install the USB Type-C and HDMI-A adapters in the display. Insert the USB Type-C and HDMI port of the NanoPi M4V2 SBC into the adapters Install the […]

January 19, 2022February 18, 2022 by Jean-Luc Aufranc (CNXSoft) - 13 Comments

10.1-inch RPI All-in-One PC review with Raspberry Pi 4

A couple of months ago I received “RPI All-in-One”, a 10.1-inch touchscreen display for Raspberry Pi boards, listed the specifications, checked out the package content, installed a Raspberry Pi 4 inside the display before booting my new all-in-one (AiO) PC successfully. I’ve now had time to spend more time with the PC/display and see how it performs under various conditions. I also tested HDMI and USB-C input features with a laptop and mini PC. Fan or fanless operation? After updating Raspberry Pi OS, I ran sbc-bench.sh script together with rpi-monitor to see how the Raspberry Pi 4 with 1GB RAM would perform under load with the (noisy) fan enabled.

sbc-bench v0.9.1

Installing needed tools. This may take some time. Done.
Checking cpufreq OPP. Done (results will be available in 11-15 minutes).
Executing tinymembench. Done.
Executing OpenSSL benchmark. Done.
Executing 7-zip benchmark. Done.
Checking cpufreq OPP. Done (17 minutes elapsed).

perl: warning: Setting locale failed.
perl: warning: Please check that your locale settings:
	LANGUAGE = (unset),
	LC_ALL = (unset),
	LC_ADDRESS = "en_GB.UTF-8",
	LC_NAME = "en_GB.UTF-8",
	LC_MONETARY = "en_GB.UTF-8",
	LC_PAPER = "en_GB.UTF-8",
	LC_IDENTIFICATION = "en_GB.UTF-8",
	LC_TELEPHONE = "en_GB.UTF-8",
	LC_MEASUREMENT = "en_GB.UTF-8",
	LC_TIME = "en_GB.UTF-8",
	LC_NUMERIC = "en_GB.UTF-8",
	LANG = (unset)
    are supported and installed on your system.
perl: warning: Falling back to the standard locale ("C").
It seems neither throttling nor frequency capping has occured.

Memory performance:
memcpy: 2595.9 MB/s (0.8%)
memset: 3398.3 MB/s (2.7%)

7-zip total scores (3 consecutive runs): 5556,5650,5565

OpenSSL results:
type             16 bytes     64 bytes    256 bytes   1024 bytes   8192 bytes  16384 bytes
aes-128-cbc      61981.49k    76335.40k    82773.25k    84199.42k    84355.75k    84393.98k
aes-128-cbc      62224.25k    76254.36k    82779.39k    84461.91k    84757.16k    84825.43k
aes-192-cbc      55900.34k    67052.89k    71500.80k    73121.11k    73362.09k    73203.71k
aes-192-cbc      55869.41k    66963.52k    71835.14k    72934.74k    73471.32k    73465.86k
aes-256-cbc      50541.63k    59834.26k    63387.14k    64413.70k    64634.88k    64760.49k
aes-256-cbc      50646.47k    59735.02k    63384.92k    64461.14k    64648.53k    64629.42k

Full results uploaded to http://ix.io/3MfY. 

In case this device is not already represented in official sbc-bench results list then please
consider submitting it at https://github.com/ThomasKaiser/sbc-bench/issues with this line:
| RPi 4 Model B Rev 1.1 / BCM2711 rev B0 | 1500 MHz | 5.10 | Bullseye armhf | 5590 | 62100 | 64690 | 2600 | 3400 | - | [http://ix.io/3MfY](http://ix.io/3MfY) |

sbc-bench v0.9.1

Installing needed tools. This may take some time. Done.

Checking cpufreq OPP. Done (results will be available in 11-15 minutes).

Executing tinymembench. Done.

Executing OpenSSL benchmark. Done.

Executing 7-zip benchmark. Done.

Checking cpufreq OPP. Done (17 minutes elapsed).

perl: warning: Setting locale failed.

perl: warning: Please check that your locale settings:

LANGUAGE = (unset),

LC_ALL = (unset),

LC_ADDRESS = "en_GB.UTF-8",

LC_NAME = "en_GB.UTF-8",

LC_MONETARY = "en_GB.UTF-8",

LC_PAPER = "en_GB.UTF-8",

LC_IDENTIFICATION = "en_GB.UTF-8",

LC_TELEPHONE = "en_GB.UTF-8",

LC_MEASUREMENT = "en_GB.UTF-8",

LC_TIME = "en_GB.UTF-8",

LC_NUMERIC = "en_GB.UTF-8",

LANG = (unset)

are supported and installed on your system.

perl: warning: Falling back to the standard locale ("C").

It seems neither throttling nor frequency capping has occured.

Memory performance:

memcpy: 2595.9 MB/s (0.8%)

memset: 3398.3 MB/s (2.7%)

7-zip total scores (3 consecutive runs): 5556,5650,5565

OpenSSL results:

type 16 bytes 64 bytes 256 bytes 1024 bytes 8192 bytes 16384 bytes

aes-128-cbc 61981.49k 76335.40k 82773.25k 84199.42k 84355.75k 84393.98k

aes-128-cbc 62224.25k 76254.36k 82779.39k 84461.91k 84757.16k 84825.43k

aes-192-cbc 55900.34k 67052.89k 71500.80k 73121.11k 73362.09k 73203.71k

aes-192-cbc 55869.41k 66963.52k 71835.14k 72934.74k 73471.32k 73465.86k

aes-256-cbc 50541.63k 59834.26k 63387.14k 64413.70k 64634.88k 64760.49k

aes-256-cbc 50646.47k 59735.02k 63384.92k 64461.14k 64648.53k 64629.42k

Full results uploaded to http://ix.io/3MfY.

In case this device is not already represented in official sbc-bench results list then please

consider submitting it at https://github.com/ThomasKaiser/sbc-bench/issues with this line:

| RPi 4 Model B Rev 1.1 / BCM2711 rev B0 | 1500 MHz | 5.10 | Bullseye armhf | 5590 | 62100 | 64690 | 2600 | 3400 | - | [http://ix.io/3MfY](http://ix.io/3MfY) |

No throttling was detected, and the temperature never exceeded 56°C in a room with an ambient temperature of 26°C. I then disconnect the fan, but it turns out the fan can also be easily disabled in the OSD menu […]

November 19, 2021January 24, 2022 by Jean-Luc Aufranc (CNXSoft) - 8 Comments

10.1-inch Raspberry Pi All-in-One touchscreen display review – Part 1: Unboxing and installation

Raspberry Pi OS All-in-One Touchscreen Display

I’ve just received a 10.1-inch touchscreen display designed for Raspberry Pi model B boards with 1200×800 resolution from the EVICIV store on Amazon that also offers models with 1366×378 and 1920×1200 resolutions, and allows users to create an All-in-One computer based on the popular SBC. The product can also be used as a standalone display connected to an HDMI or USB-C (via DisplayPort Alt mode) source, so it could be interesting for all sorts of projects and not only ones relying on Raspberry Pi boards. In the first part of the review, I’ll check out the hardware, install a Raspberry Pi 4, and boot it to check out whether it works, before going into more details in the second part of the review. RPI All-in-One Touchscreen Display Unboxing The package lists some of the specs and highlights features of the device with a built-in stereo speaker, support for older and […]

July 4, 2021July 4, 2021 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

Relay expansion board for Raspberry Pi includes 4.3-inch touchscreen display (Crowdfunding)

PiRelay 8-Channel Raspberry Pi touchscreen display

There are plenty of multi-relay boards for Raspberry Pi, but since those are often combined with an HMI for control, SB Components decided to offer an all-in-one solution with an expansion board equipped with eight relays and a 4.3-inch touchscreen display connected to a Raspberry Pi via HDMI and USB. PiRelay 8 specifications: Relays 8x relays with 3.3V/5V trigger signal Input – 250V AC/7A, 30V DC/10A Screw terminal blocks NO (Normally Open) and NC (Normally Closed) modes available Isolation – EL357NC optocouplers with current transfer ratio (CTR) of 50-600% at IF=5mA, VCE=5V Display support – Optional 4.3-inch touchscreen display with 800 x 480 pixels resolution, HDMI input for video, USB for touchscreen support. It also comes with a 3.5mm audio jack, an HDMI audio output, a speaker connector, and mounting holes for the Raspberry Pi. 40-pin GPIO header to connect a Raspberry Pi SBC (Pi 4, Pi 3B+, Pi 3, […]