Hardware Category - Page 425 of 1201 - CNX Software

April 9, 2021April 9, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

Rugged, fanless quad-camera system brings AI and Machine Vision to rolling stock and automotive applications

quad-camera system automotive AI & machine vision

Eurotech BoltGPU 10-31 is a rugged fanless embedded system powered by NVIDIA Jetson Xavier NX module, equipped with four FAKRA connectors for GMSL camera, and designed to bring Edge AI and machine vision to rolling stock (e.g. trains) and automotive applications. The BoltGPU 10-31 also features 16 GB of eMMC flash, NVMe SSD support, three Gigabit Ethernet interfaces, WiFI 6 and Bluetooth 5.1, two USB3.1 ports, as well as isolated CAN-FD, optoisolated DIO, video out, and GNSS with optional RTK. BoltGPU 10-31 specifications: System-on-Module – NVIDIA Jetson Xavier NX with hexa-core NVIDIA Carmel ARM v8.2 64-bit CPU with 6MB L2 + 4MB L3 cache, 384-core NVIDIA Volt GPU with 48 Tensor Cores (up to 21 TOPS of accelerated computing), 8 GB LPDDR4x RAM, 16GB eMMC 5.1 flash Storage MicroSD card socket Optional 512 GB NVMe SSD on M.2 Key M socket 256 Kbit Serial EEPROM Video Output – 1x Mini […]

April 9, 2021April 12, 2021 by Jean-Luc Aufranc (CNXSoft) - 11 Comments

DIY Raspberry Pi Compute Module 4 NAS supports up to four drives

We previously noted it was possible to build a Raspberry Pi CM4 NAS using Wiretrustee carrier board with a built-in Marvell 88SE9215 PCIe to SATA controller and four SATA connectors. But Mebs just created his own Raspberry Pi Compute Module 4 four-bay NAS with his own carrier board equipped with a PCIe socket used to insert a PCIe SATA card, as well as a neat 3D printed enclosure that took 6 days to print. This carrier board design is actually derived from the official Raspberry Pi CM4 IO board with only the interfaces needed for the NAS to make it smaller and fit within the width of a standard 3.5″ hard drive. It was also made as simple as possible because it was Mebs’ first PCB design. This leaves the board with Gigabit Ethernet, one HDMI port, a USB 2.0 port, the PCIe 2.0 socket, as well as some headers […]

April 9, 2021 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Eyecam open-source webcam will make you feel spied on

Most people will use webcams connected to a computer or integrated into a laptop without thinking about the possibility of being spied on, but Eyecam will certainly raise awareness and make you feel like somebody is truly watching. The open-source webcam is shaped like a human eye and acts like one thanks to a Raspberry Pi camera and an Arduino board controlling six servos for eyeball, eyelids, and eyebrows movements. The project was conducted at Saarland University in Germany, and Eyecam looks amazingly realistic – and creepy – with the eyeball and eyelids moving, especially when face tracking is enabled, and expressions are possible with servos controlling the eyebrows. The webcam is comprised of 3D printed parts, a Raspberry Pi camera connect to Raspberry Pi Zero recognized as a USB webcam from the host, and an Arduino Leonardo Pro Micro to control the 6 servo motors. On the software side, […]

April 8, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

Edge AI and robotics embedded computers feature NVIDIA Jetson TX2 NX module

NVIDIA unveiled a cost-down version of the Jetson TX2 module with the Jetson TX2 NX SO-DIMM system-on-module last month, and AAEON is one of the first companies to have updated some of their products with the new module. AAEON’s BOXER-823x-series of fanless embedded computers feature the NVIDIA Jetson TX2 NX module, and multiple Ethernet ports, including some PoE capable for the development of edge AI and robotics applications. BOXER-8230AI AI Edge Fanless Embedded Box PC This model offers a mid-range alternative between the Jetson Xavier AGX NX-based BOXER-8250AI embedded box PC and the Jetson Nano-powered BOXER-8220AI mini PC both of which offer the same ports. BOXER-8230AI specifications: SoM (CPU/Memory/Storage) – NVIDIA Jetson TX2 NX with dual-core NVIDIA Denver 2 64-Bit CPU and quad-core Arm Cortex-A57 MPCore processor @ up to 2.0 GHz, 256-core NVIDIA Pascal GPU @ up to 1.3 GHz, 4GB LPDDR4, 16GB eMMC flash Storage – MicroSD card […]

April 8, 2021December 22, 2021 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

simpleRTK2B-SBC packs 3 u‑blox ZED-F9P RTK GNSS receivers for centimeter-level GPS positioning

Real-time Kinematic (RTK) relative positioning technique allows for 1-3cm positioning accuracy with data derived from satellite-based positioning systems such as GPS, BeiDou, GLONASS, Galileo, and NavIC. We’ve previously covered Skytraq PX1122R RTK GNSS module as well as SBG Systems Ellipse-D industrial-grade inertial navigation system featuring the technology, and now Spain-based ArduSimple has announced the simpleRTK2B-SBC single board computer that aims to “simplify the development of centimeter-level positioning solutions supporting real-time kinematics (RTK)” via up to three u‑blox ZED-F9P RTK GNSS receivers. simpleRTK2B-SBC board features & specifications: MCU – STMicro STM32F7 Cortex-M7 microcontroller GNSS Positioning 184-channel u-blox ZED-F9P engine Configuration options 2x ZED-F9P for position + heading 3x ZED-F9P for position + full attitude (roll, pitch, yaw) Navigation rate up to 20Hz Position accuracy down to 1 centimeter GPS: L1 & L2; GLONASS: L1OF & L2OF; Galileo: E1 & E5b; BeiDou: B2I & B2I; QZSS and SBAS Up to 4 integrated […]

April 7, 2021April 7, 2021 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

LilyGo sells Open-Smartwatch open-source hardware ESP32 watch by “Paul’s 3D Things”

We’ve previously covered three variants of LilyGo T-Watch-2020 smartwatch based on ESP32 WiFi & Bluetooth SoC with TTGO T-Watch-2020 (V1) launched about a year ago, following by T-Watch-2020 V3 with a microphone for voice control, and T-Watch-2020 V2 with GPS. The company has recently launched a new rounded smartwatch based on ESP32-PICO-D4 SiP with a twist as they did not design it themselves and instead partnered with “Paul’s 3D Things” for the Open-Smartwatch, and just handle manufacturing and production. LilyGo Open-Smartwatch “Light Edition” specifications: Wireless module – LILYGO T-micro32 module based on ESP32-PICO-D4 module with dual-core ESP32 processor, 4MB FLASH, ceramic antenna or u.FL antenna connector Connectivity – Bluetooth 4.2 BR/EDR BLE and WiFi 4 2.4GHz 802.11 b/g/n Display – 1.3 inch circular LCD with 240×240 resolution USB – Micro USB for charging and programming Sensor – 3-axis BMA400 accelerator Debugging – USB to TTL via CH340E chip Misc -Reset […]

April 7, 2021April 7, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

GMSL2 camera kit supports 15-meter long cables, up to six cameras with NVIDIA Jetson Xavier AGX

6x gmsl2 cameras nvidia agx xavier devkit

We’ve recently seen it’s possible to use a long cable with the Raspberry Pi camera thanks to THine camera extension kit that works with 20-meter LAN cables using V-by-One HS technology. e-con Systems has now launched a similar solution for NVIDIA Jetson Xavier AGX, one of the most powerful Arm devkits available in 2021, with NileCAM21 Full HD GMSL2 HDR Camera that supports up to 15-meter long cable as well as LFM (LED Flickering Mitigation) technology. NileCAM21 camera features and specifications: Based on OnSemi AR0233 Full HD camera module with S-mount interchangeable lens holder Gigabit Multimedia Serial Link 2 (GMSL2) interface with FAKRA connector Shielded coaxial cable for transmission of power and data over long distances (up to 15m) High Dynamic Range (HDR) with LED Flickering Mitigation (LFM) Supported resolutions and max frame rates for uncompressed UYVY streaming VGA (640 x 480) up to 60 fps qHD (960 x 540) […]

April 6, 2021April 7, 2021 by Jean-Luc Aufranc (CNXSoft) - 9 Comments

Xiaomi Mi AX9000 WiFi 6 Enhanced router supports up to 1000 clients

Xiaomi launched the Mi AX6000 WiFI 6 Enhanced router, not to be confused with WiFI 6E, at the beginning of the year. The router offers up to 4804Mbps link at 5 GHz, and up to 574Mbps with a 6+1 antenna configuration, as well as one 2.5GbE port, and several Gigabit Ethernet ports. But for people requiring even more bandwidth, Xiaomi Mi AX9000 WiFi 6 Enhanced router offers even more wireless throughput using three frequency bands with four antennas each, and up to 1148 Mbps at 2.4 GHz, up to 4804Mbps at 5.2GHz, and up to 2402Mbps at 5.8GHz, which the company refers to as the 5G_Game band. Xiaomi Mi AX9000 WiFI 6 Enhanced Edition router specifications: SoC – Qualcomm IPQ8072 quad-core Cortex-A53 processor @ 2.2 GHz with dual-core 1.7GHz NPU (network acceleration engine / processing unit) System Memory – 1GB RAM Connectivity Wired 1x 2.5GbE LAN/WAN port 1x Gigabit Ethernet […]