Jean-Luc Aufranc (CNXSoft), Author at CNX Software - Embedded Systems News

November 11, 2022November 13, 2022 by Jean-Luc Aufranc (CNXSoft) - 235 Comments

Giveaway Week – RAK Developer Kit (Air Quality Kit)

RAKwireless joined CNX Software’s Giveaway Week last year with the WisBlock Kit 2 LoRa-based GPS Tracker with Solar Panel, and the company is back for Giveaway Week 2022 with the RAK Developer Kit (Air Quality Kit) with LoRaWAN connectivity. The kit includes everything to get started to build an indoor air quality monitor and send the air quality information over LoRaWAN to the cloud/LoRaWAN server. It notably comes with a WisGate gateway and a Wisblock Node with an indoor enclosure. The kit contents and main specifications are as follows: RAK7246 WisGate Developer D0 with: Raspberry Pi Zero W board with Broadcom BCM2835 ARM11 processor @ 1GHz, 512MB RAM Storage – 16GB MicroSD card Connectivity 802.11 b/g/n WiFi and Bluetooth 4.0 via Cypress CYW43438 module found on RPi Zero W board RAK2246 Pi HAT LoRaWAN concentrator module with SX1308 baseband processor Frequency bands – RU864, IN865, EU868, US915, AU915, KR920, AS923 […]

November 10, 2022 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

MediaTek unveils Dimensity 9200 Octa-core Cortex-X3/A710/A510 5G mobile processor

MediaTek has just launched the Dimensity 9200 octa-core flagship 5G mobile processor with one Cortex-X3 core, two Cortex-A710 cores, and four Cortex-A510 cores, as well as the latest Arm Immortalis-G715 GPU. Manufactured for a TSMC 4nm processor for efficiency, the new flagship processor supports mmWave 5G and sub-6GHz cellular connectivity, LPDDR5x 8,533 Mbps memory, UFS 4.0 storage, and embeds a faster MediaTek APU 690 AI processor MediaTek Dimensity 9200 specifications: Octa-core CPU subsystem 1x Arm Cortex-X3 core at up to 3.05 GHz 3x Arm Cortex-A710 cores at up to 2.85 GHz 4x Arm Cortex-A510 cores up to 1.80GHz 8MB L3 cache 6MB system cache GPU – Arm Immortalis-G715 with support for Vulkan 1.3, hardware-based ray tracing engine AI Accelerator – MediaTek APU 690 AI processor with MDLA (MediaTek Deep Learning Accelerator), MVPU (MediaTek Vision Processing Unit), SME (I don’t know what that is), and DMA Memory I/F – LPDRR5x 8,533 […]

November 10, 2022November 12, 2022 by Jean-Luc Aufranc (CNXSoft) - 395 Comments

Giveaway Week 2022 – Sonoff NSPanel Pro and Zigbee modules

The fourth prize of Giveaway Week 2022 is the Sonoff NSPanel Pro control panel with four Zigbee modules including a temperature & humidity sensor, a door/window sensor, a switch, and a PIR motion sensor. The controller is based on a Rockchip PX30 quad-core Cortex-A35 processor running Android 8.1 and acts as a Zigbee 3.0 gateway allowing users to add all sorts of Zigbee modules. It also works with the eWelink app to add security cameras which can be some of your old smartphones. We reviewed the SONOFF NSPanel Pro control panel & Zigbee gateway last month together with Zigbee modules and the SONOFF Slim Cam indoor security camera and found it worked reasonably well, although some advanced features required us to use the eWelink app in our phones instead of the touchscreen on the display. We also found one bug with the Zigbee switch that the company promised to fix […]

November 9, 2022April 15, 2023 by Jean-Luc Aufranc (CNXSoft) - 10 Comments

GL.iNet GL-MT2500A security gateway review – Part 1: Unboxing and teardown

The Brume 2 security gateway/router is powered by a MediaTek MT7981B (Filogic 820) dual-core processor @ 1.3 GHz and is available as the GL-MT2500A with a metal enclosure or the GL-MT2500 with a plastic case. GL.iNet sent me the GL-MT2500A for review. In the first of the review, we’ll have a look at the device and accessories, and tear it down to check out the hardware design and main components. I’ll then need some time to test OpenWrt 21.02 and features such as WireGuard and OpenVPN, AdGuard Home, Tor Anonymity, and soon. GL.iNet GL-MT2500A (Brume 2) unboxing The router ships with a short Ethernet cable, a 5V/2A USB Type-C power supply with EU, US, and UK plug adapters, and some minimal documentation that points to the users to more detailed online documentation and support on the company’s Facebook page. There’s not much too see on the front panel and right […]

November 9, 2022November 11, 2022 by Jean-Luc Aufranc (CNXSoft) - 148 Comments

Giveaway Week 2022 – Pico:ed Smart Cutebot Kit

The third prize of this year’s giveaway week comes courtesy of ELECFREAKS which offers a Cutebot Pico:ed kit based on the Pico:ed board with a Raspberry Pi RP2040 microcontroller and following BBC Micro:bit form factor. The kit also includes two high-speed motors to drive two wheels, ultrasonic & distance sensors, two RGB LED lights and clearance lamps on the bottom, two line-tracking probes, and an active buzzer used as a horn. It is powered by three AAA batteries. The company initially me asked me if I wanted to review the board/robot, but since I may not have the time to do so, I asked whether they wanted to be included in our yearly giveaway week which they accepted. The company provides instructions to program the robot with “Micro block” visual programming IDE, C++, and CircuitPython. You’ll find resources to get started and eight projects for the robot in the Wiki. […]

November 8, 2022November 8, 2022 by Jean-Luc Aufranc (CNXSoft) - 48 Comments

ODROID-N2L is a smaller, low-cost variant of ODROID-N2+ Arm SBC

ODROID-N2L SBC is a smaller and cheaper version of the ODROID-N2+ single board computer powered by an Amlogic S922X hexa-core Cortex-A73/A53 processor and offered with 2GB or 4GB single-chip LPDDR4X memory. While the ODROID-N2+ is the most popular board from Hardkernel, it’s also fairly larger than most hobbyist SBCs on the market, and following requests from customers, the company designed the ODROID-N2L with a compact form factor that is smaller than Raspberry Pi Model B SBCs and sold at a lower price at the cost of missing some of the features of its big brother. ODROID-N2L specifications: SoC – Amlogic S922X hexa-core big.LITTLE processor with 4x Arm Cortex A73 cores @ up to 2,208/2,400 MHz, 2x Arm Cortex A53 cores @ 1,908/2,016GHz, Arm Mali-G52 GPU @ 846MHz; 12nm manufacturing process System Memory – 2GB or 4GB LPDDR4 @ 3216 MT/s Storage – eMMC flash module socket up to 128GB, microSD […]

November 8, 2022November 8, 2022 by Jean-Luc Aufranc (CNXSoft) - 8 Comments

T8-Pro Celeron N5095 mini PC offers triple HDMI output, dual Gigabit Ethernet

T8-Pro is a low-cost mini PC powered by an Intel Celeron N5095 Jasper Lake processor that offers features such as triple 4K HDMI output and dual Gigabit Ethernet usually found in more expensive models for the industrial/embedded market. The actively-cooled mini PC is equipped with 8GB RAM and an M.2 2242 SSD of 128GB to 1TB capacity. It also comes with a WiFi 5 and Bluetooth 4.2 module, three USB 3.0 ports, and a 3.5mm audio jack. T8-Pro mini PC specifications: SoC – Intel Celeron N5095 quad-core Jasper Lake processor @ 2.0GHz / 2.9GHz (Turbo) with 4MB cache, 16EU Intel UHD Graphics; 15W TDP System Memory – 8GB LPDDR4X (Up to 16GB, but not offered for sale) Storage – 128GB to 1TB M.2 2242 NVMe SSD Video Output – 3x HDMI 2.0 ports up to 4Kp60 Audio – 3.5mm audio jack (headphone & microphone) jack, digital audio via HDMI Connectivity […]

November 8, 2022November 10, 2022 by Jean-Luc Aufranc (CNXSoft) - 123 Comments

Giveaway Week – e-con Systems e-CAM20_CURB camera

Today, we’re giving away the e-con Systems e-CAM20_CURB is a 2.3MP color camera with a global shutter that is designed to work with Raspberry Pi 4 SBC. The camera is based on ON Semiconductor AR0234CS CMOS sensor and supports uncompressed video at 1920 x 1200 (2.3MP) up to 60 fps, 1920 x 1080 (Full HD) up to 65 fps, and 1280 x 720 (HD) up to 120 fps. I just completed the e-CAM20_CURB camera review with Raspberry Pi 4 last weekend and found the video smoothness and quality to be much better than most cameras I’ve tried when there is motion, even in relatively dark scenes, since motion blur and artifacts are reduced. The company provides Yocto Linux and Raspbian/Raspberry Pi OS images with V4L2 drivers and Gstreamer tools, and the camera was fairly easy to use with the Yocto image thanks to the useful documentation provided with the kit. […]