Processors Category - Page 595 of 1188 - CNX Software

January 12, 2019 by Jean-Luc Aufranc (CNXSoft) - 21 Comments

tinyWiFi-5G is a NanoPi NEO Air Clone with 5 GHz WiFi

NanoPi NEO Air is a tiny Allwinner H3 board with 802.11 b/g/n WiFi connectivity that launched in 2016 for $17.99 and is now available as NanoPi NEO Air-LTS (Long Term Support) for $28 and up. A company – or group of software developers – called tinyDebian decided to create a clone based on NanoPi NEO Air design, but replacing the 2.4 GHz Ampak AP6212 802.11n WiFi + Bluetooth 4.0 LE module by a dual-band Realtek RTL8821CS module that supports 802.11 b/g/n/ac and Bluetooth 4.2 LE. Meet tinyWiFi-5G. NanoPi NEO Air comes with two different storage configuration (8GB or 32GB flash), but tinyDebian did not provide the full specifications of the board, so tinyWiFi-5G board specifications below are preliminary: SoC – Allwinner H3 quad-core Cortex A7 @ 1.2 GHz with an ARM Mali-400MP2 GPU System Memory – 512 MB DDR3 Storage – 8GB eMMC Flash + micro SD card slot Connectivity […]

January 11, 2019 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Edu-C Arduino Compatible Board Targets Education & Game Development

Sometimes learning can be boring, and a potentially good way to get kids more engaged is to learn by playing. Edu-C Arduino compatible board is designed to teach game development to kids old and young, so they have a lasting reward once they complete programming of the board, or they may decide to customize the game further. Edu-C hardware specifications: MCU – Microchip Atmel AVR328 microcontroller Display – 28×64 pixel OLED display + 1-digita 7-segment display Game Inputs – Left and right potentiometers Misc – 8x LEDs, left & right LEDs, RGB LED, on/off power switch, reset button, buzzer USB – 1x micro USB connector for programming (CH340) and power Power Supply – 5V via USB; LiPo battery support The board ships with a 200 mAh Lipo battery, and a charger. Educational materials are also provided, but only in French right now, except for some documents which are in English. There […]

January 11, 2019 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

Obvious is an App Store for Embedded Devices

Mobile devices have gotten their own app stores for more than 10 years already, with Google Play for Android and Apple App Store for iPhones and iPads. Linux powered IoT devices – usually gateways – also got their own app stores with branded Ubuntu app stores relying on Ubuntu Snaps, although I’m not sure they are widely used. However, low power embedded devices usually based on microcontrollers did not get their own app store, and Obvious aims to fill this gap with the Obvious platform, an app store for embedded devices, which enabled after-sales features and upgrades. Obvious app store is currently in Beta and works exclusively with Nordic Semi based products at this stage. We don’t know an awful lot about the services, except it will enable a new revenue stream for providers of low power wireless IoT devices. Some benefits listed by the company include: Untapped resources – […]

January 11, 2019January 15, 2019 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

ANAVI Thermometer WiFi Board is Designed for Home Automation (Crowdfunding)

ANAVI Technology launched several open source hardware boards for the Raspberry Pi and ESP8266 maker communities in the past, starting with RabbitMax Flex home automation HAT for Raspberry Pi, and several others including ANAVI Light Controller ESP8266 board to control LED strips. All boards are designed with KiCad opensource EDA software, and I’ve tested several already such as ANAVI Infrared pHAT or ANAVI Light Controller, and found documentation to be very good and easy to follow. The company has now launched another ESP8266 board with ANAVI Thermometer that allows you to monitor temperature and humidity, effectively acting as a thermostat for home automation. ANAVI Thermometer specifications: SoC – Espressif Systems ESP8266 Tensilica L106 32-bit processor Connectivity – WiFi 802.11 b/g/n Display – Mini OLED display Build-in sensor – AM2302 (DHT22) temperature and humidity sensor Expansion Terminal block for DS18B20 waterproof temperature sensor UART pins 3x slots for I2C sensors Misc – […]

January 10, 2019April 13, 2021 by Karl Johnson - 29 Comments

Radxa Rock Pi 4 Review – Part 1: A First Look at RockPi 4B Performance Set

Hey, Karl here with another RK3399 board. This one is by Radxa and is called the Rock Pi 4. There are 2 main variants to this board and I was shipped the B version “performance set” which includes a power supply, heatsink, and acrylic case. Also shipped was 16gb eMMC 5.1 module, eMMC flashing board, and USB-TTL debug cable. It looks like the difference is the B version has AC wifi and GbE LAN with PoE support with a hat. The A version only has GbE. Rock Pi 4B Performance Set Unboxing Some of the more notable specs eMMC module support M.2 NVME SSD support (SATA not supported) HDMI 2.0 4k@60htz MIPI DSI 2 lanes via FPC connector 3.5mm audio jack MIPI CSI 2 lanes via FPC connector, support up to 8MP camera 802.11 ac wifi Bluetooth 5.0 40-pin expansion header : 1 x UART 2x SPI bus 2x I2C […]

January 9, 2019March 31, 2020 by Jean-Luc Aufranc (CNXSoft) - 17 Comments

ClearFog CX LX2K Networking Board is Powered by NXP LX2160A 16-core Processor

SolidRun started their ClearFog family of networking boards back in 2015 with Marvell ARMADA based ClearFog Pro board exposing 7 Gigabit Ethernet ports, an SFP cage, mPCIe/mSATA sockets, and more. Since then the company has launched several other ClearFog boards with small variation in the name with the latest being ClearFog CX 8K equipped with a COM Express module based on Marvell ARMADA A8040 quad-core Arm Cortex A72 processor. Today I was made aware that the company leveraged of the flexibility of having a COM Express module by offering a more powerful version of the board – ClearFog CX LX2K – powered by NXP LX2160A networking processor with 16 Arm Cortex-A72 cores, 100GbE support, 24x PCIe Gen4 lanes, and more. The rest of the specifications are pretty much the same since the COM Express carrier board – pictured above – remains the same: COM Module – CEx7 LX2K module with […]

January 9, 2019 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

Rockchip RK1808 Cortex-A35 NPU Delivers up to 3.0 TOPS

Rockchip RK3399Pro was expected to be the first processor from the company featuring an NPU (Neural Processing Unit) to accelerate artificial intelligence workloads, but eventually went through a redesign, and the community found it gave birth to RK1808 NPU by looking at a device tree file in the Linux kernel. Rockchip has now made the NPU official at CES 2019, and we now know a little bit more. Here are the specifications shared by the company: Dual-core Arm Cortex-A35 CPU NPU computing performance up to 3.0TOPs supporting INT8/INT16/FP16 hybrid operation VPU supporting 1080P video codec Built-in 2MB system-level SRAM Display – MIPI/RGB video output Camera – MIPI/CIF/BT1120 Camera video signal input with built-in ISP Audio Microphone array support with hardware VAD function for low-power monitoring and far-field wake-up Audio output I/O PWM/I2C/SPI /UART USB3.0/USB2.0 PCIe interface Support for Gigabit Ethernet and external WiFi/Bluetooth modules Manufacturing – 22nm FD-SOI process It […]

January 9, 2019 by Jean-Luc Aufranc (CNXSoft) - No Comments

NXP Immersiv3D Enables DSP-Free Dolby Atmos & DTS:X Audio Systems

High-fidelity audio systems such as soundbars, smart speakers, and AV receivers have traditionally relied on DSPs (Digital Signal Processors) to deliver low-latency audio processing, and enable audio and video synchronization. DSPs add to the cost of the overall design however, and with Immersiv3D technology, NXP has leveraged Arm Cortex-A53 and M4 cores in their NXP i.MX 8M Mini processor to completely remove the need for DSP in audio systems, shaving the BoM cost by up to 20% according to an article on EETimes. Immersiv3D also enables immersive audio support with Dolby Atmos and DTS:X, advanced audio pre/post processing, advanced features like voice control for the smart home. Immersiv3D audio solution was designed to help OEMs to bring to market affordable consumer audio devices with Dolby Atmos and DTS:X, and beside the audio processing software, NXP is also offering an Immersiv3D audio reference design to help them delelop sound bars based […]