development board News - Page 109 of 261 - CNX Software

December 9, 2018December 8, 2018 by Jean-Luc Aufranc (CNXSoft) - 11 Comments

Buildroot For NanoPi NEO4 RK3399 SBC

NanoPi NEO4 is the smallest and cheapest RK3399 board so far, featuring the hexa-core processor into a $45 60×45 mm single board computer. FriendlyELEC usually provides decent documentation and software support for their boards, but Flatmax was not satisfied with the build system provided by Rockchip / FriendlyELEC. So he took the matter into his own hands, worked on and released a buildroot external tree for building NanoPi NEO4 SD card images. Flatmax mentioned this is the first completely contained build system for the NanoPi NEO4. The build process is explained on Github, and basically goes like this: Clone buildroot

git clone git://git.busybox.net/buildroot buildroot.neo4

1	git clone git://git.busybox.net/buildroot buildroot.neo4

Install dependencies

sudo apt-get install -y build-essential gcc g++ autoconf automake libtool bison flex gettext
sudo apt-get install -y patch texinfo wget git gawk curl lzma bc quilt

1 2	sudo apt-get install -y build-essential gcc g++ autoconf automake libtool bison flex gettext sudo apt-get install -y patch texinfo wget git gawk curl lzma bc quilt

Clone NEO4 buildroot external tree

git clone git@github.com:flatmax/NanoPi.Neo4.buildroot.external.git NanoPi.Neo4

1	git clone git@github.com:flatmax/NanoPi.Neo4.buildroot.external.git NanoPi.Neo4

Build the system

. NanoPi.Neo4/setup.sh yourPath/buildroot.neo4
mkdir yourPath/buildroot.dl
make

. NanoPi.Neo4/setup.sh yourPath/buildroot.neo4

mkdir yourPath/buildroot.dl

make

Flash it to the micro SD card

sudo ./output/images/sd-fuse-rk3399/fusing.sh /dev/sdX buildroot

1	sudo ./output/images/sd-fuse-rk3399/fusing.sh /dev/sdX buildroot

Just replace /dev/sdX with your actual SD card device. Jean-Luc Aufranc (CNXSoft)Jean-Luc started CNX Software in 2010 as a part-time endeavor, before quitting his job as a software […]

December 6, 2018December 6, 2018 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

PHYTEC phyCORE-AM65x SoM Features TI Sitara AM654x Processor

We already knew Texas Instruments was working on AM654 processor, the first 64-bit Arm SoC from the company, featuring four Cortex A53 cores, a PowerVR SGX544 GPU, dual lock-step capable Cortex R5F cores, and interfaces targeting industrial applications. Now at least one company has announced a system-on-module based on the solution. PHYTEC phyCORE-AM65x is equipped with AM654x processor, DDR4 and ECC DDR4 memory, up to 32GB eMMC flash, as well as built-in Ethernet, WiFi, and Bluetooth connectivity. phyCORE-AM65x specifications: SoC – Texas Instruments Sitara AM65x with 4x Arm Cortex-A53 cores, dual-core Arm Cortex-R5F MCU subsystem, PowerVR SGX544 GPU, 6x PRU-ICSSG System Memory – DDR4 with support for discrete DDR4 ECC Storage – Up to 32GB eMMC Connectivity Optional 2.4 or 5GHz Certified WiFi Solution 10/100/1000 Mbit/s Ethernet PHY on SOM Board-to-board connectors – 2x “high-density PCB interconnects” Dimensions – 65 x 55 mm The company provides Linux (Yocto Project), Android, […]

November 23, 2018November 23, 2018 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

ODROID-XU4 and ODROID-XU4Q Boards Going for $49 (Promo)

ODROID-XU4, and its fanless ODROID-XU4Q sibling, are neat little single board computer packing lots of power into a small form factor. I tested ODROID-XU4 with Ubuntu 18.04 recently and was relatively impressed by how well it worked considering it’s an Arm platform, as there were still admittedly some limitations. But as they say at $59 a board you can’t beat the price. Except you can actually do, as Hardkernel is offering both ODROID-XU4Q and ODROID-XU4 for just $49 during Black Friday here and there. If you’ve already forgotten about the board it is equipped with a Samsung Exynos 5422 octa-core Cortex A15/A7 processor, 2GB RAM, eMMC module support, Gigabit Ethernet, USB 3.0, HDMI 1.4, and more. You can read the full specifications here. The only difference between ODROID-XU4 and ODROID-XU4Q is the latter comes with a large heatsink, while the former is cooled by fan. If you are currently shopping […]

November 21, 2018November 21, 2018 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

Diskio Pi 13.3″ DIY Tablet Kit for Raspberry Pi – Take 2 on Kickstarter

Diskio Pi was a DIY tablet kit for Raspberry Pi, ODROID-C2/XU4 and other compatible boards with a 13.3″ Full HD display that launched last year on Kickstarter. But the project failed likely due to the high costs (350 Euros and up for early bird pledges without battery nor SBC) and an elevated funding target of 400,000 Euros. But the team did not give up, worked on reducing costs, improved the design, and recently relaunched Diskio Pi on Kickstarter with a more achievable 52,096 Euros target, and reasonable pricing with rewards starting at 189 Euros including VAT. Diskio Pi “basic” DIY tablet kit content and main specifications: Display – Innolux 13.3″ TFT/IPS display with 1920×1080 resolution, WLED backlight + 10-point touch capacitive panel connected over USB 2.0 Video control board with HDMI 1.4 to eDP converter, stereo amplifier, and 2x 1W speakers Daughter board with Genesys USB hub, 9V to 5V/4A […]

November 21, 2018 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Microchip Releases Tiny SAM R34/R35 LoRa SiPs and Development Kit

Microchip has been offering RN2483 & RN2903 LoRa modules for respectively 868 MHz and 915 MHz frequencies for several years, but the company has now announced SAM R34 and SAM R35 LoRa systems-in-package (SiP) that offer similar functionality in a much smaller form factor. Both SiPs integrate a Microchip SAM L21 Arm Cortex-M0+ based MCU,a sub-GHz RF LoRa transceiver operating from 862 to 1020 MHz, and a software stack. That means you don’t need different SiP depending on the region, and the only difference between SAM R34 and SAM R35 is the latter does without a USB interface for lower cost. Microchip SAM R34/R35 key features and specifications: MCU – Arm Cortex M0+ MCU @ 48 MHz System Memory – Up to 40 KB RAM including 8KB LP-RAM Storage – Up to 256 KB Flash for application code and stack Wireless Connectivity 862 MHz to 1020 MHz coverage Up to 20 […]

November 20, 2018November 20, 2018 by Jean-Luc Aufranc (CNXSoft) - 47 Comments

ODROID-H2 Intel SBC Launched for $111

Hardkernel introduced ODROID-H2 single board computer with an Intel Celeron J4105 processor last month. The first Intel board from the company supports up to 32GB RAM via two SO-DIMM sockets, as well as M.2 NVME SSDs and SATA drives, and exposes various other ports such as HDMI 2.0 and DisplayPort video outputs, dual Gigabit Ethernet, and more. We already knew most details about the board, except for the price and exact launch date. Hardkernel launched the board today for $111 on their online store with shipments scheduled the start on November 27th. Here are ODROID-H2 specifications again with letters in parenthesis referring to the location on the photo below: SoC – Intel Celeron J4105 quad core processor @ up to 2.3 GHz (real frequency) with 12EU Intel UHD Graphics 600 (A) System Memory – Dual-channel Memory DDR4-PC19200 (2400MT/s) supporting up to 32GB RAM in total (B) Storage – M.2 PCIe […]

November 17, 2018November 19, 2018 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Allwize K2 IoT Board Supports 169MHz Wize LPWAN Protocol (LoRa alternative)

LoRa, Sigfox, and NB-IoT are probably the most popular low power long range wireless protocols for the Internet of Things, but there are several others, including one I had never heard of: Wize. The Wize Low Power Wide Area Network (LPWAN) protocol has been created in late 2017, leverages the “old and refurbished” 169 MHz frequency, support up to 20 km range, 20-year battery life, and is managed by the Wize Alliance with members including STMicroelectronics, Suez, Sagecom, Renesas, Analog Devices, Silicon Labs and many others. Despite being a recent protocol, the table below claims 3 millions of deployment for Wize, and showcases some of differences against LoRa, NB-IoT, and Sigfox. You may be confused as how the standard was created in at the end of 2017, but there are so many deployments, and 13 years experience. It appears Wize is derived from the older EN 13757 standard for gas […]

November 16, 2018November 16, 2018 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

Intrinsyc Open-Q 605 SBC is Powered by Qualcomm QCS605 IoT Processor

Qualcomm QCS603 / QCS605 “Internet of Things” processors were announced last spring as the first “Qualcomm Vision Intelligence Platforms” from the company and designed for artificial intelligence and computer vision applications. Both SoCs are octa-core processor with two performance Kryo 300 Gold cores, and six efficiency Kryo 300 Silver cores, but QCS605’s big cores are clocked at a higher 2.5 GHz frequency, and the processor comes with better 802.11ac Wave2 WiFi, support for up to 32MB camera, and 4K video capture. However so far, there was no development platform publicly available, and this has just changed with Intrinsyc announcing Open-Q 605 single board computer (SBC) and development kit featuring Qualcomm QCS605 vision intelligence platform. Open-Q™ 605 SBC Specifications SoC – Qualcomm QCS605 octa-core processor with 2x high-performance Kryo 300 Gold cores up to 2.5 GHz, 6x low-power Kryo 300 Silver cores up to 1.7 GHz, Hexagon 685 DSP with Hexagon vector […]